Search Documents

Training by Inclusiveness ?Background ?Video ?Results ?Partners ?How SEM works ?Future of SEM Background: Inclusivity partners ?Northwest Community College ?Smithers Exploration Group ?With support from the Province of BC ?Federal government ?And First Nations across the northwest

May 1, 2010

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015

By S. G. Coultis

Turner Valley is in the foothills of the Rocky mountains, at an altitude of 4,000 feet, and is 42 miles south west of Calgary. The present producing area is 8 miles long by 1 1/2 miles wide, while drilling is being carried on over an area of 10 miles by 2 miles . There are 32 wells producing, 26 wells drilling, and 17 wells shut down, making a total of 75 wells, which range in depth from 2,160 feet to 5,900 feet, varying according toa the well location on the anticline centre wells being shallower than those located on the flank. The first indication of possible production in this field was a gas seepage on the banks of Sheep river, in what is now the Royalite plant yard (Figure 1). Geologically, this seepage proved to be located on an anticline running through the valley in a southwesterly direction. The Calgary Petroleum Products Company was formed in 1912, and under the direction of Mr. A. W. Dingman, President, and associates, the first well was drilled. Production was obtained in this well. Gas was found in several horizons from 884 feet to 3,960 feet, and oil at 1,557, 2,718 and 3,839 feet. In May, 1914, oil was struck at a depth of 3,839 feet, this being a light straw-coloured oil of 60 gravity, which was blown spraying from the well accompanied by three to four million feet of gas. The latter contained some 200 grains of hydrogen sulphide per 100 cu. ft., giving it the disagreeable odour so well known in Turner Valley gas. This strike caused considerable excitement and started the famous 1914 boom, when some 400 oil companies were formed. The well referred to produced from two to five barrels of 60 gravity oil per day, and 4,000,000 cu. ft. of gas. The oil was used in the crude form in cars and trucks.

Jan 1, 1929

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Alan Bauer, Melvin A. Cook

Measured detonation pressures of "prills and oil" (94/6 ammonium nitrate/fuel oil) and three of the new "slurry" blasting agents are presented and compared with computed, ideal detonation pressures and with detonation pressures expected from the measured detonation velocities. Results seem to show that the peak pressure in the detonation wave in these cases is the Chapman-Jouguet pressure and that no "spike" exists in these detonation waves. The absence of the Zeldovich-von Neumann "spike" is noteworthy in view of the very long reaction zone lengths of these mixtures. The measured detonation pressure of one of the slurry blasting agents (DBA-3") under steel confinement ( 172 kilobars) is shown to be considerably greater than the ideal detonation pressure of 75 per cent gelatin dynamite (p. = 135 kilobars) despite the fact that the detonation was still somewhat non-ideal in "DBA-3," its computed ideal detonation pressure being 180 kb. The popular 94/b AN /FO blasting agent exhibited a detonation pressure of only 13.5 kb in 5" paper tubes, but 37.5 kb in 5"• steel pipe compared with a computed ideal pressure of 40 kb.

Jan 1, 1961

By J. P. Mogan, E. D. Dainty, K. Katsuyama

"The Volvo BM 861 U articulated truck is one of the few underground diesel units manufactured by an organization which shares the same corporate roof as the engine manufacturer. As a consequence, the unit has provided an opportunity for the characteristics of the entire system- turbocharged aftercooled engine, transmission and exhaust scrubber- to interact to minimize emission levels. The performance of the components of the system, as evaluated by full-scale dynamometer testing, is summarized. The over-all effect of the various innovations was a 38% reduction in the recommended ventilation level over that of the bare engine.IntroductionThe Mining Research Laboratories of Energy, Mines and Resources Canada is required, as part o f the certification service of the Canadian Explosive Atmosphere s Laboratory, to test the exhaust emissions of diesel engines, and to recommend appropriate amounts of fresh ventilating air to minimize the risks to health of underground personnel working with, or in the vicinity of, such diesel engines. Volvo BM AB of Sweden made application for the certification of the BM 861 U truck during a period in which EMR personnel were engaged in a number of research projects concerned with improving the environment in dieselized mines. One such avenue of research was the venturi or high-energy scrubber; as the BM 861 U was equipped with this type of scrubber , EMR and Volvo BM agreed to cooperate in a considerably more extensive investigation than would be normal for a certification application. The outcome of some of this research is summarized in this paper."

Jan 1, 1981

By K. R. Brown, P. L. Krawchuk

In-situ recovery (ISR) is under increased investigation as a viable methodology for the extraction of minerals in ore bodies that may be uneconomic to mine by traditional methods or for resources situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash and uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. ISR allows for the extraction of metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in a process that produces very little to no waste rock or tailings. This paper aims to discuss the geological conditions that make ISR amenable to an ore body as well as the application of maturing technologies such as advanced directional drilling and the creation of artificial permeability that will help to access deep ore bodies and enhance or create favorable recovery conditions for ISR in the ore body. INTRODUCTION In-situ recovery (ISR), also referred to as in-situ leaching, is a potentially disruptive technology for the mining industry. ISR is under increased investigation as a viable methodology for the extraction of valuable minerals that may be uneconomic to mine by traditional methods or for deposits situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash mining, uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. Recently there has been increased interest in deploying ISR in hard rock applications due to a number of factors: the drive for environmental stewardship is stronger than ever, technological advances in drilling, blasting, and leaching are strengthening ISR economics, and a large inventory of ore bodies exists that are not feasible to mine or extract using conventional open pit or underground mining techniques. ISR allows for the extraction of valuable metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in solution via a recovery process that produces very little to no waste rock or tailings. Where the right conditions exist, the ISR process has a much smaller environmental footprint (Hiam-Galvez, 2018) and potentially much lower capital and operating costs than using conventional mining techniques.

Jan 1, 2019

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By Gérald Riverin, Bernard Salmon, Marlo Gagnon, Réemi Asselin, Alain Cazavant, Michel LaBrie

"The Ansil deposit is located in the Noranda mining camp in the southern part of the Abitibi greenstone belt. /twas discovered in 1981 and production began in 1989 with proven reserves of 1.58 Mt grading 7.2% copper, 0.9% zinc, 26.5 glt of silver and 1.6 glt of gold. It is centered at a depth of 1.3 kilometre and represents one of the deepest ore discoveries ever made from surface.The deposit consists of a single massive sulphide lens located at the contact between the Northwest Rhyolite and the Rusty Ridge Andesite. The lens strikes north-south and dips 50° east. The thickness of the lens may reach up to 35 m and can change very abruptly both along strike and along dip. The maximum thicknesses of the sulphide lens are reached in its upper (western) and at its lower (eastern) edges, thus giving the deposit its present shape of two sulphide domes connected by a thinner central portion. The lower dome is underlain by a thick accumulation of massive magnetite which may reach 10 to 15m in thickness. The upper and lower domes are underlain by two distinct pipe-shaped zones of stringer and disseminated sulphides which merge with a larger stringer zone at depth.The Ansi/ deposit displays strong relationships between its morphology and the distribution of metals. Hydrothermal alteration consists of chloritization and sericitization. Chlorite alteration is closely associated with stringer sulphide mineralization while sericite is developed in diffuse zones bordering the chloritic zones. Unlike other similar deposits, the Ansil deposit is characterized by very extensive alteration and sulphide mineralization in the hangingwall of the massive sulphides. Several features of the deposit are consistent with an origin from a submarine hydrothermal system which was particularly long-lived, and which thus promoted the build-up of very high fluid temperatures with extensive replacement (and enrichment) of pre-existing sulphides after their original deposition onto the seafloor."

Jan 1, 1990

By W. R. Bacon

"The Canam property is in southern British Columbia, 24 miles southeast of Hope. It is reached by 5 miles of road from Mile 26 on the Hope-Princeton Highway.Between the years 1930, when the property was discovered, and I 938 development work by The Consolidated Mining and Smelting Company of Canada, Limited included some open-cuts and six adits totalling 2,700 feet in length. Canam Copper Company Ltd. explored the property intermittently from 1947 to 1955 by diamond drilling and underground work, including driving No. 10 adit. From surface down to the level of No. 10 adit, about 1,250,000 tons of ore has been outlined with an approximate grade of 1.25 per cent copper, 0.8 ounce silver per ton, and 0.01 ounce gold per ton. The ore in the upper part of the deposit also contains a little molybdenum and a little uranium.In June, 1955 Canam Copper Company Ltd. made arrangements to have the property brought into production under the direction of Mogul Mining Corporation Ltd. of Toronto, and a new low level adit has been started.GENERAL GEOLOGYThe principal rocks on the Canam property are chert, cherty argillite, and argillite. They are considered to be Jurassic or Lower Cretaceous in age. Although massive bands to 150 feet in thickness occur, these rocks are in general thinly bedded. Conformable bands of pyrrhotite, a fraction of an inch in thickness, are not uncommon in the well-bedded rocks, and fine tourmaline can be observed in various places.The sediments strike slightly west of north and dip quite steeply, generally eastward; however, sharp divergences from this general attitude are fairly common.Dark grey dioritic sills, in which slender prismatic crystals are conspicuous, are fairly common in the sediments. In general the sills are less than 25 feet in thickness, but a few are as much as 100 feet thick. Under the microscope the sills are seen to consist largely of amphibole (pargasite) and plagioclase (near An50)."

Jan 1, 1949

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989