Search Documents

By Westcott PC

The development of a coal project must pass through a number of phases, taking it from a preliminary evaluation through to detailed mine planning. For each phase the cost of data acquisition and associated mining studies increases exponentially for linear improvement in confidence levels. Within each mine planning phase there are four main activities. These are the economic ordering of reserves, the development of optimum mining strategies, mine design and scheduling and finally the estimation and analysis of costs. The development of the optimum mining strategy is one of the most critical aspects of a mining evaluation and the application of economic criteria at this stage of the project is vital to the successful generation of an optimised mine design. A recommended method is the concept of Economic Ratio (ER) which expresses the likely cost of mining from a given location in a deposit in terms of the value of the product likely to be recovered. The most economic mining strategy will be to mine areas from low economic ratio to high economic ratio within the constraints of reasonable equipment application. When selecting equipment a particular machine should not be selected solely on comparison with other machines in isolation, but the total application must be analysed. In the final selection the decision should be based on whether or not it has a beneficial effect on overall project economics. The economic assessment must take into account the time value of money, so the real cost can be determined with adequate provision for capital and operating costs over different time spans.

Jan 1, 1983

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

In the sixteenth century the Spanish Captain da Alvaro Soavedaro, on a search for the explorer Ferdinand Magellan, came across the main island of New Guinea which he named Isla del Oro (Island of Gold). Since that time exploration for, and mining of, gold has been pursued by many, culminating in . the development of major world-class projects in the latter part of the 20th century. Though various prospectors have panned for gold and small gold mining projects were undertaken through the seventeenth and eighteenth centuries, it was not until the 1880's when mining became a more concerted economic venture. Misima and Woodlark Islands in Milne Bay, Gura-Ackera and Yoada in Oro, and Lakekamu in Gulf Province and Keveri in Central Province were all gold producers by late nineteenth century. It was in the 1920's that corporations began mining in PNG and with the commencement of production at Panguna in Bougainville in 1972 a new era of mega-project mining began.' Today there are two large mining projects producing mainly gold and copper. The first, already mentioned, is Panguna on Bougainville Island. This project has provided Government with $US 475 million in taxes. ok Tedi is the second large mine development located in Western Province. It began production in 1984 with the extraction of the deposit's "gold Cap".

Jan 1, 1987

Authorisation No.66 (to Prospect) was allocated to R.W. Miller & Co. Pty. Ltd. on 1st November, 1976. Exploration has brought coal reserves to measured status in the Jerry's Plains sub-group which are about 550m. thick. The immediately lower Vane Sub-group, about 200m. thick, includes about 20 seams. The total measured and indicated reserves of the two sub-groups based on the criteria adopted by the company amount to 1362 million tonnes in situ. This very large resource is subject to very many mining constraints both physical and economic which limit the saleable reserves under present conditions to about 120 million tonnes. The results of the calculation of reserves after exploration is complete in a deep multiple seam situation is dependent upon the criteria used to include or exclude seams in the reserves. These criteria are state- ments of the miner's expectations of the market, mining and coal preparation technology, local and national politics and the law as it may be applied in the future.

Jan 1, 1979

By R Trueman

An improved ability to predict dilution for narrow vein deposits enables more accurate economic comparisons between mechanised longhole stoping and other narrow vein mining methods, as well as reducing uncertainty surrounding dilution estimates for deposits at the prefeasibility/ feasibility stage. This paper proposes narrow vein dilution prediction and minimisation strategies for both greenfield sites and operating mines, respectively. The narrow vein dilution method (NVD method) is a tool for more accurately predicting longhole narrow vein dilution. The method is based on a new concept called benchmark stoping width. Benchmark stoping width is based on probabilistic analysis of overbreak distributions from a typical longhole narrow vein mine. The premise for the NVD method is that dilution associated with longhole stoping can be predicted using the benchmark stoping width. In addition to dilution prediction, the NVD method also includes strategies for narrow vein dilution minimisation generally, including; filling, cablebolting, stress relaxation, extraction sequencing and blast overbreak.

Jan 1, 2008

The mining industry was one of the first industry groups to be confronted by and to respond to public and government pressure to improve its environmental management. Companies operating in New Zealand and the parts of Australia with firmer environmental and planning controls responded quickly with environmental staff appointments to their development and operating arms. Even in less demanding jurisdictions in Western Australia and Papua New Guinea environmental staff were added to the payrolls. The issues then and now were seen as pollution related with land and water housekeeping leading to progressive or eventual site rehabilitation. Increasingly, however, environmental issues are being recognised as being more complex. They are about equity and social justice. Pollution of water, air or land is seen by the public as a question of personal and public rights, more or less wherever the pollution takes place, on public or private land. Environmental issues in mining have become caught up in the global perspective and a more holistic approach to environmental management. Environmental issues touch every comer of the community and action is being demanded. Nowhere is this better illustrated than on Bougainville Island where increasingly militant demands by land- owners for redress for environmental degradation from the Panguna Mine, on close examination, revealed many years of disenchant- ment with the government and the mining company over a wide range of social, cultural and environmental issues. Failure to address this satisfactorily eventually led to a bloody rebellion and finally an act of secession.

Jan 1, 1991

The accuracy with which block estimates are perceived is obtained by calculation of the kriging variance. This is dependent upon the model chosen for the semi-variogram of the deposit. For an extensive series of spherical semi-variograms the changes in the kriging variance resulting from various degrees of misassignment of the relative nugget effect are investigated. The results are reported as contour maps of percentage change in kriging variance as a function of the range and relative nugget effect of the true model.

Jan 1, 1985

By Batterham RJ

A 'research model' can be used to investigate cause and effect relations and generally improve the understanding of extractive metallurgical processes. As such, it is a useful research technique which complements the traditional methods of laboratory and plant measurement. The procedure of model development is iterative and involves observation of the process, hypothesis of phenomena, prediction using mathematical descriptions of the phenomena and comparison of predictions with real-world measurements. Lack of agreement of predictions with real-world measurements usually indicates an inadequacy in the hypotheses and necessitates revision. Experimentation has an integral role in the process of model development but its emphasis is different from that when experimentation alone is used to study processes. Since a process as a whole is investigated by using a model, experimentation is restricted to the study of specific phenomena to aid the description of these in the model, to the characterisation of the raw materials (for initial values of the model parameters) and to the measurement of physical and chemical constants required in the model equations. Similarly, plant measurements are made for the purpose of comparison with the model predictions not to establish cause and effect relations. This makes plant experimentation much simpler and cheaper'since most measurements-can be taken during normal operation.

Jan 1, 1984

By G Muller, P Larrondo, M C. Godoy

The categories of Mineral Resources and Ore Reserves that may be used for public reporting in Australasia are defined in the current JORC Code (2004). Most internationally accepted codes emphasise the principles of transparency, materiality and competence in classifying resources. They also provide some guidance in considering the impact of data quality. There is no method recommended in the JORC Code to classify a Mineral Resource into the allowed categories of Measured, Indicated and Inferred for public reporting. A clearly defined procedure is desirable for many reasons, including consistency, repeatability and auditability. The demonstrated use of geological knowledge in the classification method is desirable. In deposits with abundant historical data there can be large variations in data type and quality. Quantification of the error of the estimates may also be considered. Ways to formally incorporate such information into the resource classification process are presented as a first step towards establishing an objective, repeatable methodology that allocates resources into appropriate categories based on defined criteria of accuracy and precision.

Jan 1, 2006

By A D. Ferreira, A E. C, A D. Padovezi

The increasing market requirements regarding the quality of products, the enhanced predictability from detailed mine planning, the need for process consolidation and upgrading require continuous investigation on the characteristics of different ore types to be concentrated. This paper addresses the mineralogical and technological characterisation of several itabirite iron ore types and the influence of the composition and mineralogical associations on desliming and flotation. Pellet feed quality and the influence on the major performance indicators, such as weight recovery of slimes, selectivity index, metallurgical recovery, flotation kinetics of iron minerals and gangue is also emphasised. The investigation resulted in a classification of iron ores according to their mineralogical composition, morphology of the crystals, and/or texture and microstructure of mineral particles with respect to desliming and flotation performances.

Jan 1, 2005

By Herbst JA

During the last decade, it has been established that conventional mineral-processing control strategies based on classical control theory result in significant increases in plant throughput and operating-cost saving. The proper education and training of personnel using dynamic simulators of the principal unit operations is vital for proper design and maintenance of control systems. Severe multivariable interactions and numerous constraints on both manipulated and state variables in grinding/classifica-tion and flotation systems can be studied using time domain analysis with proper dynamic simulators. Two interactive programs are described, and the basis of each simulator and its structure are discussed. Two examples concerned with choosing, tuning, and decoupl-ing of manipulated and controlled variables for a grinding/classification circuit (DYNA-MILL II) and for a rougher flotation circuit (DYNAFLOAT II) are presented. The way in which these dynamic simulators can be used for the design of model-based control strate-gies is also outlined. A brief description of the use of these dynamic simulators for screening alternative strategies and circuit optimization is given.

Jan 1, 1985

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

By A G. Pavlides, B L. Weekes

The Sepon Copper Project is located in the Savannakhet Province of Laos PDR and is operated by Lane Xang Minerals Ltd (LXML). An Ausenco - Bateman Engineering joint venture, the Khanong Development Group (KDG) managed engineering, procurement and construction of the project. The plant was fully commissioned in March 2005, two weeks ahead of schedule. The plant is designed to produce 60 000 tpa of cathode copper. The process flow sheet includes a pressure oxidation (POX) circuit that leaches pyrite flotation concentrate to generate ferric ions and sulfuric acid for use in atmospheric leaching of a predominantly chalcocite ore. The process is unique in that the chemistry in the autoclave is forced to produce a basic ferric sulfate precipitate for downstream recovery of ferric iron. This paper describes the design, construction and commissioning of the pressure oxidation circuit. The challenges imposed on construction and commissioning due to the remote location of the site, landlocked status and underdeveloped infrastructure in Laos are highlighted.

Jan 1, 2005

AustraliaÆs record-breaking drought, efforts towards environmental best practice and the current commodities boom is demanding water use and reuse as never before. Mining practices, processing, the remote communities and support industries require vast amounts of specific quality water. Sustainability of water use has been a key factor in mine development, expansion of existing operations and increasing profitability of processes involving water. Developments in water treatment technology have enabled the use of a range of processes to produce this water reliably at ever decreasing costs. This increasing acceptance of new technologies has seen seawater desalination, recycling of plant wastewater streams, municipal wastewater reuse and others to become commonplace. Processes including seawater and groundwater reverse osmosis (RO), low pH RO, thermal desalination, high rate clarification, brine water treatment, ion exchange and other advanced treatment technologies are now used as part of mining operations. This paper surveys the trends in water treatment for the mining industry both in Australia and internationally with a review of technologies and case studies of operating plants. The key technologies are explained with an emphasis on the specific requirements for mining operations û unusual raw water, process and operations limitations, environmental concerns, as well as harsh climate. Case study information from several mining operations is included.

Jan 1, 2006

By J Champa

The mining industry internationally seems on the verge of a major underground support revolution as suppliers, mines, consultants and researchers develop, test and use thin support (structural) membranes (or superskins as they are commonly called) mainly as a replacement for screen/wire mesh. Thick membrane support in the form of shotcrete (sprayed concrete) has been used since the 1950s in underground mines. Shotcrete, in mines, is generally applied at a thickness between 25 and 100 mm depending on the need. Thin membranes are however applied at a typical thickness between 2 and 6 mm. Certain thin membranes have been available for several years (Tannant et al, 1999), but the intense interest in such supports has only grown in the last few years. The interest lies mainly in the potential to safely reduce the mining cycle time and hence improve productivity. There is however considerable confusion concerning such supports, and this paper attempts to clarify certain aspects and dispel certain misconceptions and myths about thin support membranes.

Jan 1, 2000

By Ritchie I

Copper minerals are often associated with gold ores. These create processing problems since cyanide solutions are not selective for gold alone. Copper minerals are also leached by cyanide, and typically each one per cent of `reactive' copper in the ore consumes about 30 kg t 1 cyanide. Once in solution, copper cyanide species create further processing problems as they adsorb onto carbon along with the dicyanoaurate ion. These problems make conventional cyanidation of gold ore uneconomic if the ore contains too much copper. As a result, methods of economically processing gold-copper ores are becoming of increasing importance.One of the more promising methods of treating these ores is by selective leaching of the gold by an ammoniacal cyanide solution, a method first described by Hunt in 1901. This method is already in commercial use in Mauritania, treating copper/gold tailings. In general terms, the addition of I - 2 g U1 ammonia to a standard cyanide leach solution causes a significant increase in gold extraction and decrease in copper extraction. However, early testwork on this system has concluded that the optimal leach conditions are critically dependent on ore composition, and the mechanism is not well understood, making predictions of best conditions impossible.

Jan 1, 1997

Against a background of deeper pits, the introduction of prestripping fleets and the need for closer control of operating costs (especially the waste removal component), Australian coal operations utilising draglines have in recent years become increasingly focused on:1. assessment of more efficient excavation methods; and2. application of explosive products and initiation systems which offer more flexibility than ever before.Additionally, developments in blast performance assessment techniques and equipment, and computer modelling and excavation monitoring systems have provided an improved opportunity to design a blast to achieve a desired profile suited to the excavation equipment and Sequence.

Jan 1, 1992

Access to secure and reliable water resources is fundamental to the minerals industry. In recognition of that requirement, and cognisant of extensive contemporary public water debate and reform initiatives in Australia, the Minerals Council of Australia (MCA) approached the Ministerial Council on Mineral and Petroleum Resources (MCMPR) proposing the establishment of a Joint Working Group to prepare a framework of strategic principles to ensure responsible water management at a site and corporate level, manage risks and identify opportunities. The Framework provides high-level guidance on issues that should be addressed in water decision making across Australia in relation to mining and associated processing operations. It identifies principles and objectives for adoption in four areas, viz: valuing water, strategic water planning, implementation, and engaging stakeholders. Given the high level nature of the Framework, and its national application, it does not seek to replicate detailed guidelines already widely available in each state and territory on operational water management practices and associated regulatory issues at mine sites. The Framework includes a series of case studies from across Australia that demonstrate where strategic thinking, wise water management and close consultation with stakeholders has delivered better water use, more profitable operations and excellent community/stakeholder relationships. The Framework was formally launched on behalf of MCMPR by the Western Australian Minister for Resources at the MCAÆs Sustainable Development Conference in Perth in October 2006. No full paper available for this extended abstract

Jan 1, 2006

By V S. T Ciminelli

This work aimed at evaluating the acid rock drainage (ARD) potential of five samples of a Brazilian gold sulfide mine in a decommissioning process. Three of the most traditional ARD prediction techniques, Standard Acid Base Accounting (Std ABA), Modified Acid Base Accounting (Modified ABA), as static methods, and humidity cells as a kinetic method were tested. Both the Std ABA and the Modified ABA results indicated an acid generation potential for some of the studied samples. In the other cases the results were inconclusive. The five samples were then submitted to humidity cell tests during 27 to 30 weeks. At the end of the period, the leachate pH was stabilised in a range from 3.4 - 4.1 (four samples) to 5 (one sample). The presence of relatively high levels of sulfate and dissolved metals was detected throughout the operation, specifically, Ni and Zn, and less frequently, As. These findings are discussed with the help of the samples mineralogy and Eh-pH diagrams. The results obtained in this investigation indicated potential environmental risks of this mining area. In this particular case, the kinetic tests were shown to be essential to the identification of the samples ARD potential.

Jan 1, 2003