Search Documents

By Mur D. M

Metal ferrites are formed by the high temperature reaction of various metal oxides with hematite and are commonly found in the calcines derived from the sulfation roasting of zinc, copper and nickel sulfide concentrates. The Jarosite Process is designed to treat such zinc ferrites by hot acid dissolution but little information is available on the basic reactivity of various ferrites and the effect of Eh. As part of an overall study of the reactivity of calcine products from copper and nickel sulfide concentrates it has been found that Eh plays an important role in the rate of dissolution of magnetite, hematite and nickel oxide by HC1 and H2SO4. Further studies on the reactivity of pure synthetic copper,zinc,and nickel ferrites also show a dependence on Eh. This paper discusses the relative reactivity of iron oxides and metal ferrites in 1 M HC1 and the results of electrochemical studies using cyclic voltammetry. A mechanism for the dissolution reaction is proposed as well as factors which determine their leaching. It is shown that the rate of leaching of metal ferrites with HC1 is enhanced in the presence of reducing agents such as Cu(I) and Sn(II). By contrast the leaching of NiO is enhanced by oxidising agents such as Cu(II).

Jan 1, 1987

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

By Paterson M. R, Spencer P. A

Vitrokele technology is a resin process that can be applied in gold plants to reduce both capital and operating costs. The Vitrokele resin can be used for both precious metal recovery and for recovering free and combined cyanide from effluent streams. Vitrokele resin has been extensively tested at pilot plant level and is now applied successfully at a commercial heap leach facility in Zimbabwe where it is used in place of activated carbon for recovery of gold from pregnant leach solution. Significant capital cost savings were achieved by installation of a resin plant instead of a conventional carbon adsorption plant. Operation to-date has not seen any significant physical or chemical degradation of the resin either in terms of adsorption capacity/kinetics or physical appearance/size. This gold recovery process is equally applicable to slurry streams where it would be implemented in stirred tanks with interstage screens in a similar manner to a conventional carbon adsorption plant.

Jan 1, 1996

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By McPherson M. J

An experimental investigation was carried out to determine the various gas flow characteristics of bituminous coal samples. Adsorption and desorption tests were first conducted to estimate the quantity of methane that is retained by coal, and the rate at which it is released. Experiments were then carried out to study the variation in coal permeability with changes in applied stress and gas pressure - factors that change continuously with time. To further understand the phenomena involved in retention, release, and flow of gas, electron microscopy was used to study the microstructure of coal and how it affects these characteristics of coal.

Jan 1, 1988

With mining development on hold and other underground works in a slowdown, the development of nuclear wa te repositories takes centre tage on the American rock engineering scene. Three repositorie for commercial spent fuel-in salt, tuff, and basalt-are in the phase of site characterisation and conceptual design, and one pilot project for defense high-level wa te in salt is under construction. A repository design for crystal line rock has recently been postponed.Because of strict quality assurance requirements throughout design and construction, and because of the need to predict and ascertain in advance the satisfactory performance of the underground openings, much intellectual energy has been expended to analyse underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behaviour and improved methods of underground analysis and design. For the shorter term, a formalised ground control plan was developed, the principles of which may be applied to other types of projects.This paper summarises the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1988

Cannington is a Broken Hill type deposit discovered by BHP Minerals, now BHP Billiton, in 1990. The deposit is located south east of Cloncurry, Queensland, Australia. The deposit occurs in the Eastern succession of the Mount Isa Inlier within the Soldiers Cap Group. The mineralisation is interpreted to be confined to two limbs of a synform wrapped around a core amphibolite. The silver, lead and zinc mineralisation is zoned within silicic and mafic units. There is a strong association between silver and lead. The combination of mafic and silicic zoning, differing relative grades of silver, lead, zinc and iron, the relative position of the mineralisation on the synform limbs and differing metallurgical performances have resulted in the identification of ten different ore types, four of which are currently extracted. Ordinary Kriging (OK) is used as the resource estimation methodology for the silver, lead and zinc mineralisation. This modelling approach has performed quite well for resource reporting and long term mine planning. However the limitations of this modelling technique to adequately provide information on a local stope scale has lead to the geological staff to consider alternatives to this approach. Limitations of the current modelling method apply to both the geometry of the orebodies and the grade variability. Since early-2000 the Cannington geologists have been experimenting with modelling both the distribution of the mineralisation types using Probability Field conditional simulation (PF) and the distribution of grade using Sequential Gaussian Simulation (SGS). This approach to local modelling of mineralisation type and metal grades using conditional simulation (CS) has undergone a full evaluation by comparing grades estimated for stopes using both the (OK) resource model and conditional simulation (CS) models. The mine planning staff have used the CS derived models, and have found improvements in grade predictions over the currently utilised Ordinary Kriging û derived resource model.

Jan 1, 2003

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this 'pure coal' basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

By Lacy JC

Human habitation of the Pacific Rim began when mankind began migrations out of its place of origin in the Rift Valley of Central Africa c. 4million years ago. This migration was erratic and largely controlled by advances and retreat of the various Ice Ages which, while limiting advances in areas of intense cold, at the same time aided migration thro-ugh the creation of land bridges as ocean levels declined during periods of glacial advance (Fig.l).Mankind began its trek to the Pacific from Africa across India then north into southern China and south into Indonesia (Fig.2). In part, these migrations stimulated early technological develop-ments to fulfill needs and adapt to environmental conditions; thus, these nomads developed stone and bone tools, animal skin clothing and the use of caves and other simple shelters. The earliest evid-ence of mankind's use of fire can be found at Zhou-koudaian near Beijing, c.400,000 BP.From China, the completion of the Pacific Rim's population can be attributed to the last Ice Age that dropped the ocean level by more than 300 feet and created land bridges about 40,000 BP allowing migration across the Bering Strait into Alaska and to Australia from Indonesia. The American migration reached Mexico about 30,000 BP, and by 6000 BP the occupancy of the Pacific Rim was complete when the first human settlers reached the southern tip of Chile.

Jan 1, 1990

Comminution of solids is surely one of the oldest technologies which even in this day and age of DNAs, chips and space exploration continues to challenge our scientific acumen and engineering ingenuity. In essence, this challenge is two-fold. One, as much as three to four per cent of all electric power generated world-wide is consumed in crushing and grinding primarily because the utilisation of energy is woefully poor. Studies have shown that the efficiency of mechanical size reduction processes is of the order of 1.5 to 12 per cent only (Schoenert 1986). Two, with the grinding technologies available to us, we have, at best, inadequate and, at worst, almost negligible control over the shape of the comminuted particles, size dispersion of the ground mass, and the sharpness of mineral liberation. Low energy efficiency and lack of control in the sense mentioned above have far-reaching implications for resource conservation, performance of down stream unit operations, and damage to the environment. Our problem is in fact central to the mineral-energy resources triangle shown in Figure 1 which depicts the close interrelationships among mineral resources which are becoming poorer in content and more complex in mineralogy each day, energy resources which are depleting rapidly without any viable alternate on the horizon, and environmental concerns which can no longer be ignored. It is evident that any improvement in the efficiency of the comminution process impacts directly on the control of environmental damage, conservation of energy and the economics of the operation. These concerns have special relevance for the processing of non-ferrous ores.

Jan 1, 1992

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

By G W. Croft, L E. Krause

The current copper ore handling systems in use at Xstrata CopperÆs Mount Isa Copper Operations are up to 33 years old and have hoisted over 160 Mt at a rate of around 6 Mtpa. The mineÆs production profile is increasing in line with the optimum life of mine plan to over 6.6 Mtpa, which requires a system utilisation and reliability above that previously achieved. Copper ore is hoisted up the U62 shaft, which forms the central part of the U62 ore handling system. In theory this system can cope with the duty planned if the bottleneck is only the U62 winder. To achieve the planned production rate will require increased focus on reliability of each component in the ore handling system so that ore is available at the shaft for hoisting whenever the shaft is available, and the shaft is available for the maximum practical time. Increased availability will be achieved through the outcomes of the study of each component in the U62 system, and the internal ore handling systems that deliver ore from as far as 2 km laterally and 700 m vertically from the U62 shaft. The true capacity of each component is being determined and current performance is being measured with the aim of improving performance through root cause analysis and engineering out the causes of delays. The program began in March 2004 and this paper describes the progress achieved as of April 2005.

Jan 1, 2005

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

The appearance of the Cornish miner in South Australia was, in the simplest terms, the result of resource development economics. In Cornwall in the middle of the 19th century tin and copper mining was declining, while in the new colony of South Australia copper mining was booming. Experienced hard rock miners in Cornwall there- fore escaped unemployment at home by accepting an assisted passage to South Australia. There, in a colony where they were needed, they made their skills available and received good wages. There are many testimonies which support this simple thesis. Take for example the following extracts from contemporary newspapers in Corn- wall: Persons of small capital will find this an excellent opportunity for emigrating to the young and thriving colony ... The miner will find a rich and unbroken field for his operations. The Colony abounds with minerals... (West Briton, 19 July 1844) Miners make a great deal of money here (South Australia). All of them earn ú2 to ú3 per week and in many cases when they have a portion of the mine on tribute one person has cleared ú100 in a couple of months or so. (Cornwall Royal Gazette, 21 July 1848)

Jan 1, 1987