Search Documents

In 1972, with the West Lyell Open Pit winding down, mining operations transferred underground. All development tunnelling until the end of the decade was carried out by a fleet of ten pneumatic Jumbos.A decision was made in 1980 to purchase an electric-hydraulic Jumbo and a second was purchased in 1982. Their introduction changed the face of development at Mount Lyell. Significant new demands were placed on main-tenance sections, particularly on electrical reticulation.Subsequently, two further electric-hydraulic Jumbos were purchased from Agnew Mining in 1984, and successfully overhauled and commissioned. As well, two electric-nydraulic production drilling rigs have been purchased. Only one of the original pneumatic Jumbos remains in service.

Jan 1, 1985

By Anderson RJ

Tower Mills are used at Aberfoyle's newly commissioned Hellyer base metal sulphide concentrator. Hellyer ore is particularly fine grained. To achieve adequate liberation fine grinding is necessary. Three Tower Mills are used on regrind duties, grinding to less than 20 microns. The physical arrangement, material flows and grinding characteristics for the Hellyer Tower Mills are described. The mills have performed satisfactorily, both in size reduction and power efficiency. Wear parts must be inspected and changed more often than with ball Mills. To date, 92 per cent availability has been achieved. As parts and maintenance routines are rationalised, this is expected to improve to 96 per cent. Modifications to wear parts for the Hellyer Tower Mills are discussed.lhc Tower Mill grinding environment is highly reducing. The impact of Tower Mill regrind on downstream flotation is discussed.

Jan 1, 1991

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

By Zhou A, Cadogan J. M

Direct reduction of iron ore (DR) is one of the promising technology emerging in the world's steel industry. Kinetics and Mossbauer studies of DR with hydrogen have been carried out at two temperatures of 600¦C and 800¦C in this investigation. The results show that different controlling steps govern the reduction rate at different temperatures. The mechanism was also found to vary during the reduction. The Mossbauer spectra of the samples reduced in various time intervals were studied to determine the phase changes during reduction.

Jan 1, 1997

By P Pelletier, J Tessier, C Duchesne

This paper summarises research into the study of the control of flotation processes based on froth images. A review of the froth flotation operation background and the relevance and role of the froth phase are presented. The use of numerical image analysis techniques for the extraction of significant patterns from industrial flotation froths is discussed. First, the froth was analysed by the use of the multivariate image analysis (MIA) method to extract the spectral variation contained in a RBG image. The partial least squares (PLS) method was applied to develop an empirical model for the prediction of froth grade. The results of this application are illustrated using an industrial case study. Second, the froth was also analysed by grey-level co-occurrence matrix (GLCM) and wavelet transform analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths. They also provide qualitative information on the changes in the visual appearance of the froth. The pros and the cons of those methods are highlighted. Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses the reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained from the implemented control strategy are highlighted. Finally, the feasibility of implementing a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.

Jan 1, 2005

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Mistra M, Hu JS, Wadsworth ME

The fluorite/oleate system has been studied extensively since the begin- nings of flotation research. The well-defined relatively simple crystal structure of fluorite and its ionic bonding make it a model system for study. Our understanding of fluorite/ oleate flotation chemistry continues to grow but as yet remains incomplete. Besides a review of our understanding of this system, recent findings are presented in this paper, and new research horizons are identified.

Jan 1, 1984

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

The Northland Peninsula of northern North Island, New Zealand contains a complex and diverse record of volcanism which reflects rapid tectonic changes during the late Cenozoic. The main volcanic associations observed on the peninsula are late Cretaceous- early oceanic crust obducted onto Northland at the end of the Oligocene, Miocene arc-type rocks and Pliocene-Quaternary intraplate basalts. This sucession of volcanic successions can be related to tectonic convergence developing into subduction and followed by a an environment of tectonic tension. While the volcanic activity is ultimately linked to specific tectonic regimes, because of rapid change magmatism was decoupled from the specific tectonic event. This decoupling of magmatism and tectonism appears to be a feature of the zones of plate interaction in the southwest Pacific region.

Jan 1, 1990

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

By Lewis W. H, Leigh M. C, Mayercheck W. D

The U. S. Department of Interior's Bureau of Mines, in conjunction with a cooperator in the U. S. A., are developing a new highwall mining system (HMS) for coal extraction in unreclaimed and active contour strip mines. This prototype system is comprised of a computer-based remote control (CBRC) system to monitor and remotely control a thin-seam continuous miner (TSCM) and a 76*m long multiple-unit continuous haulage (MUCH) conveying system, plus other manually- operated support equipment located on the highwall bench. The TSCM and MUCH coal haulage system are both controlled remotely by a single operator in a protective enclosure at an ergonomically- designed workstation located on the highwall bench. Two other personnel work on the bench to operate other support equipment. Full-scale mock-up fabrications were employed in the design of the unique remote control operator workstation. The HMS should allow the safe and economical exploitation of increased coal reserves where they outcrop in hilly regions of the United States. It should also be competitive with conventional auger mining and other coal extraction techniques, with a productivity goal at a highwall site of 20 tonne/man-h. Extensive simulated surface tests of the miner and haulage system should be completed in early 1988 at Bureau test facilities at Pittsburgh, Pennsylvania. These will be followed by actual coal production trials of the entire system in 1988 at a highwall site in West Virginia/USA.

Jan 1, 1988

By Xizhen J

Point load testing for irregular rock specimens was studied to determine the relationship between tensile and compressive strengths, drill penetration rate and other rotary drilling parameters. The DH-l type point load tester was developed and more than 2 000 irregular specimens of over 60 kinds of rock from 16 mines and quarries were tested. The effects of size, shape and number of samples on the point load strength index were investigated, using regression analysis. Experiments were carried out to investigate the relationship between point load strength index and uniaxial compressive strength on 29 kinds of rock. The relationship between these values and the drill penetration rate for rotary and percussion drills is discussed.

Jan 1, 1986

By Agrawal A, Joshi A

Mochia mine, in culmination of depillaring operations, fired India's largest underground pillar blast consuming 145 tonnes of explosive and yielding 0.55 million tonnes of ore in June 1994. To protect main mine structures (situated at a distance of 250 to 350 m from the blast site) from resultant ground vibrations, the charge per delay was restricted to 2300 kg. The post-blast observations revealed that no damage was caused to these structures. However, the damage assessment survey of the mine workings situated in close proximity revealed a general trend in consonance with the distance from the blast and found to be well correlated with peak particle velocity.

Jan 1, 1995

By Blair J. R

A Train Performance Calculator (TPC) is an essential tool in railway operations, as a means of acquiring quickly a precise measure of the performance of the system. Traditionally the TPC was used in the form of program for a large computer. By employing an efficient integration algorithm and tailoring the program to suit the computer system it is shown that it is possible to devise a TPC for a mini computer. The resulting low running costs and flexibility of operation makes this a useful design tool. This TPC was developed to study problems associated with a single track railway operation. It was applied specifically to study the railway operated by the Mt. Newman Mining Co. Limited in the Pilbara region of W.A. to transport iron ore from the mine to the port. The TPC was used to calculate the effects of changes to locomotive power, to train size, to the track and to the amount of traffic. Its accuracy was checked by comparing its performance with that of the actual trains.

Jan 1, 1977

This paper presents a new idea in field data collection for geological and scientific data. The computer keyboard has been replaced by a barcode wand driving a spreadsheet style editor. To use the full capabilities of computer hardware currently available, geotechnical and geological data can be entered and validated in the field, in a structured format, for later transfer into modem geological modelling databases. An example, using a geotechnical borehole log, explains the principles discussed. The generic nature of the Datcol system is illustrated by the application developed using the Norwegian Geotechnical Institute Rock Mass Classification system. A brief description of a modem spatial relational database is also given with particular reference to underground engineering.

Jan 1, 1993

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

In todayÆs demanding business landscape continual change and technological advancement is a given. With these changes there is now, more than ever, a need to ensure sustainable growth in respect of value protection and value adding whilst meeting the pressures and expectations of the societies in which we operate. Traditionally the management of safety has been a very reactive activity in the business, in some cases seen as an irritation and a disruptive process that demands a focus on preventing reoccurrences. This in turn has focused the measurement of safety performance on a range of lagging indicators û æafter the effect managementÆ. Gaining and maintaining a licence to operate is crucial to a sustainable business but as a prerequisite, organisations need to have a demonstrable ability to manage the safety of their people, as well as mitigating the people risk associated with the business activity. A major focus in the last decade has been on the implementation of enterprise risk management programs, where risk becomes embedded in all business systems and processes and the organisationsÆ genetic make up is programmed to analyse and integrate risk management into all facets of the business activity. The management of safety should be no different. One school of thought argues that there are no new accidents, but rather our inability to learn from the past. Others believe that as long as we have an appetite to achieve the unachievable, we will have to continue to push the boundaries, our safety comfort zones and inevitably take risks. Single reliance on highly evolved technical systems, elaborate processes, highly skilled people, safe equipment and safe work environments have shown one thing û they are not sustainable in providing adequate coverage in the business. In analysing a range of factors associated with some of the worst catastrophes of the 20th century, it can be suggested that they were in fact predictable and inevitable and that an integrated approach underpinned by sound risk management systems could have determined a different result. The key to a sustainable approach in the management of safety requires us to look at a multitude of aspects that collectively allow the performance of an organisation to be predictable. To have certainty in the business activities it is necessary to have controls in place that will mitigate the risks normally associated with unwanted events. It is ensuring that human factors effectively contribute to monitoring the planned approach and being able to safely adjust to any variability. In essence this is having the ability to proactively plan for the longer term. The sentiments articulated by organisational leaders echo that safety management is good business. Surely then a good business is a sustainable business, and a sustainable business is one that provides lasting benefits to its stakeholders.

Jan 1, 2006

By Walker BV

Mining activity has been an integral component in the New Zealand economy since the early days of European settlement. Recently in common with other Pacific Rim countries there has been a resurgence of investment in gold. A sustained and increasing exploration effort has resulted in the rapid development of alluvial gold mining operations, a number of hard rock gold discoveries, and a general optimism about New Zealand's prospectivity. New Zealand's attitude to mining development, in particular hard rock gold mining is influenced by high environmental values and a concern, largely through absence of examples, that modern mining may not perform to community standards. While these environmental concerns are wide spread there is a growing realisation that gold mining, if properly managed, can take place within acceptable environmental standards and that it has the potential to contribute significantly to New Zealand's economy. New mining developments have an important role to play in this process. The mining industry in New Zealand is now at a crossroads. Having invested substantially and confirmed the potential for gold mining developments it has found itself in a rapidly changing economic environment as the Labour Government puts in place a number of fundamental economic reforms. The reforms are intended to free up the economy removing the rafts of subsidies and protective measures which have stultified initiative and growth. A fundamental reform of the public service has been initiated including corporatisation of trading activities and the establishment of a Department of Conservation to administer estensive areas of Crown land. Both petroleum and mining taxation are being reviewed with the intention of creating a more neutral competitive environment. Mining legislation is also being re-examined with both efficiency and equity objectives. While the current environment is characterised by uncertainty and rapid change, the outcome will be a more market-oriented stable policy environment, to the mutual benefit of the industry itself and the New Zealand Community.

Jan 1, 1987