Search Documents

At 11 p.m. on Tuesday, 24th July 1979, an explosion of methane gas in a three heading development panel at Appin Colliery resulted in the deaths of fourteen men. The explosion followed after or was asso- ciated with a changeover of the ventilation to achieve a central intake between two returns. Investigation by Inspectors was followed by separate Judicial and Coronial Inquiries. Investigational information aimed at understanding the circumstances of the ex- plosion was prepared for the Inquiries. Recommendations following the Judicial Inquiry have been adopted by the Department of Mineral Resources.

Jan 1, 1981

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

By Stewart Gillies A D, Just G. D

An internationally recognised and uniform method for classification, categorisation and designation of mineral and energy resources is not yet available. With the increasing need for reliable and comparable coal resource data it is necessary to standardise the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can considerably improve classification quality. A review is undertaken of major classification with particular emphasis on those that incorporate limits on estimation error.A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed.Application of the classification algorithm for resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results that closely reflect the error associated with an estimate of resource quantities based on current sampling densities.lbis requires a careful geostatistical analysis with an emphasis on geological awareness. Resource category restrictions although albitrarily assigned should remain constant for all deposits being compared. This requires some engineering judgement with additional interpretation also required for isolated and peripheral block.

Jan 1, 1990

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003

The conventional approach to the disposal of fine coal mine tailings, which involves piping the tailings as an aqueous slurry to a storage where they remain in the form of a permanent wet deposit, is becoming unacceptable. This approach is a legacy of a "contain and forget" mentality, which has economic advantages only in the short term. In the longer term, wet tailings deposits occupy large areas of land and present extreme rehabilitation difficulties. Alternative tailings disposal systems, which are sustainable and which facilitate rehabilitation, are required. The possible alternatives include the mechanical dewatering of fine tailings prior to disposal in combination with coarse reject, tailings disposal into spoil pile valleys, and the combined pumping to disposal of tailings and coarse reject. The most appropriate choice of fine tailings disposal strategy will vary from mine site to mine site. The chosen strategy should be optimised to meet increasingly stringent environmental requirements, within the constraints imposed by each mine. The alternative approaches represent significant departures from past practices, and require considerable industry driven research and development before they can be adopted with confidence. All three alternatives involve mixing of the fine tailings and coarse waste streams, aimed at creating a mixture of reasonable engineering properties. Understanding the engineering behaviour of such mixtures is central to the success of these alternative disposal strategies.

Jan 1, 1991

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining' machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

The need to solve the problems associated with spontaneous combustion, system of ventil- ation and methane drainage in gassy coal mines has brought about the development of mining and degassing methods which has made possible up to 80% gas recovery in retreating longwalls. Beneficial results also were obtained mostly in the double or multiple-entry systems, but for single-entry systems and for a seam thickness exceeding 3 m, gas recovery rate is still very low. With some single-heading systems, such as those where a return roadway is not maintained in the goaf behind the face line, a new methane drainage technology is practiced. Attempts were made to extract methane from roof holes drilled from offsets in the ribside of the longwall block. The inclinations and lengths of the boreholes were planned and designed on the basis of the geological and mining condit- ions encountered at the time and every second hole was terminated precisely at the point where the previous hole intersected the immed- iate roof goaf area above the face. There are mathematical relations approp- riate to the design of the above drainage systems to give optimum methane recovery under the given conditions. Some examples of drainage have reached 87% recovery and have attained 94% CH4 purity.

Jan 1, 1982

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

BHP is the world's largest copper concentrate producer with production from mines at Escondida (Chile), Ok Tedi (Papua New Guinea), and Island Copper (Canada). The entire concentrate production is further processed into refined copper by third-party smelters around the world. In anticipation of an expansion in the global copper concentrate production capacity and a corresponding increase in treatment and refining charges by copper smelters, BHP has continuously evaluated various opportunities for downstream copper processing. An expansion in the Escondida mine production, combined with BHP's interest in processing some of its concentrate production on-shore in Chile, ultimately resulted in the development of the Escondida Leach Process. This process was specifically developed for higher grade concentrates, such as from Escondida. An ammoniacal lixiviant and air are used under ambient conditions to leach less than one-half of the contained copper values. After solid-liquid separation, the solution is subjected to solvent extraction regenerating the ammoniacal lixiviant and the copper loaded organic phase is stripped in spent electrolyte returned from the electrowinning plant where ultra-high quality SX-EW copper is produced. The solid leach residue can, if required, be upgraded by flotation to produce a high-grade copper concentrate with improved fuel values and a pyrite tail for disposal. After an 18-month bench and pilot plant scale program and an engineering feasibility study, Minera Escondida Limitada decided to build an 80 000 tonnes of copper per year facility near Antofagasta, Chile. The installed investment cost amounted to around $160 million. The plant went into commercial production in November 1994 and better than 99.9995 per cent Cu cathodes were produced right from the start. BHP believes that the process and the commercial plant are an excellent example of a novel approach advancing the science of copper metallurgy in harmony with present demands for environmentally sound processes and high quality products.

Jan 1, 1995

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

There are two mechanisms in the flo- tation process by which particles are transported from the pulp to the con- centrate: bubble-mineral aggregation and entrainment. It is the chemical processes which occur in the pulp which are critical to the success of flotation since they control the floatability of different min- erals and the selectivity which can be obtained. However, these chemical pro- cesses are so complex that metallurgists are still limited in their ability to predict the floatability of particles in industrial circuits by consideration of the minerals present and the chemical environment. The alternative approach to understand- ing flotation is to examine the behaviour of minerals in industrial flotation pro- cesses, to recognise similarities and differences, and to define the "laws" which appear to apply. Using this ap- proach it has been found that minerals float at a rate which is proportional to their concentration in the pulp, and that the rate of flotation of different min- erals is influenced by variables which' affect the pulp or the froth phase. The ultimate application of this approach is the use of models for circuit simulation purposes. It is this alternative approach which is the theme of this paper. One of the most important problems in understanding the technology of flotation has been in defining the characteristics of the particles being floated. Particles entering flotation vary widely in size and mineral composition, and different par- ticle types float at different rates. These rates do not change uniformly as operating variables change. It has been conventional practice to assess flotation performance in terms of the metal contents of total streams because no better method has been available, and this procedure has obscured important effects which occur in

Jan 1, 1984

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By S Jeon, K Aikawa, M Ito, A Kusano, I Park, N Hiroyoshi

In mineral processing of complex sulfide ores containing copper (Cu), lead (Pb), and zinc (Zn), flotation has been commonly used. Typical Pb mineral in the ores is galena (PbS), while some types of the ores contain anglesite (PbSO4). This article reviews our recent studies on the effects of coexisting PbSO4 on the flotation of complex sulfide ores, and a method to suppress the floatability of sphalerite (ZnS) in the presence of PbSO4 was proposed. Comparison of flotation experiments for different types of model samples showed that PbSO4 makes the separation of Zn from Cu difficult; that is, for the model sample containing PbS without PbSO4, Zn could be separated from Cu, while when the model sample containing PbSO4, Zn was recovered together with Cu as froth. Solution analysis and thermodynamic calculation suggested that Pb2+ was released from PbSO4 and reacted with ZnS to form PbS, acting as an adsorption site for the flotation collector, xanthate. This would be the main reason for high floatability of ZnS in the presence of PbSO4. As a method to suppress ZnS floatability for the ores containing PbSO4, a pre-treatment of the ores to remove PbSO4 prior to flotation was proposed. The results of model experiments using mixture of ZnS and PbSO4 showed that ~97 per cent of PbSO4 was dissolved within 30 minutes of pretreatment using ethylenediaminetetraacetic acid (EDTA) as extractant, and thus ZnS floatability was markedly suppressed. Moreover, Pb2+ extracted from PbSO4 during the pre-treatment could be recovered as zero-valent Pb by the cementation using zero-valent Fe as a reductant. The details of ZnS flotation in the presence of PbSO4 and the effects of the pre-treatment are discussed based on the results of surface analysis like XPS.

Aug 24, 2022

By C Reed

Titaniferous magnetite deposits are a significant source of vanadium for use in high strength steel alloying and other chemical applications. The mineralogy of the deposits varies markedly and the ore characteristics strongly influence the process route selected and the metallurgical outcomes. Characterisation of the ores reveals the presence of magnetite, ilmenite and other minerals such as spinel hematite and goethite with variable degrees of weathering along with weathered products of host rock. The standard processing route is to crush, grind and magnetically recover a concentrate for salt roasting to produce a soluble vanadate. Ore beneficiation is practised to generate an iron based mineral concentrate containing much of the vanadium with low silica levels of two per cent. Typical processing problems encountered are fine liberation size, over grinding of the magnetite and variable response to magnetic separation resulting from the weathering profile. Beneficiation options are restricted, and generally focused on producing a combined iron and titanium rich concentrate containing vanadium due to the fact that ilmenite and magnetite and their products of weathering are magnetic and have similar specific gravities making their separation difficult. The ilmenite usually contains low levels of vanadium making its separation highly desirable from the iron mineralisation containing higher levels of vanadium. Salt roasting of vanadium ores followed by water leaching has been the standard processing route for many years. The cost of suitable sodium salts, availability of capital and increasing energy costs and energy availability are critical factors in determining the viability of aspiring vanadium producers. To date, only Windimurra has acquired full capital funding, secured energy and sodium salt supplies at suitable cost that enable the construction of the project. Low overall recoveries of vanadium to concentrate roasting at up to 1200¦C are critical cost issues. In this paper, factors influencing the recovery of vanadium are reviewed and emerging processing trends explored. The important features of the processing of titaniferous magnetites have been condensed from the literature, published works, company websites, our own work and personal communication.

Jan 1, 2008

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005