Search Documents

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Armstrong M

The Clermont Coal Mine will export steaming coal from the Wolfang Basin in Central Queensland, Australia. It is expected to be developed in the mid-1990s.The majority of the reserves lie in the 30 m thick Wolfang Seam. Overburden depth varies from 80 m at the subcrop line to 190 m in the centre of the basin.

Jan 1, 1992

By D Olwagen, C Stanton, J Gerber

From December 2013 to February 2014 the Southern Middleback Ranges magnetite concentrator went through a successful optimisation process that included the installation of extra grinding power to treat a wider range of ore types. After the initial improvements, sampling surveys were conducted to identify the mineral deportment through the concentrator. Samples collected during the survey were analysed using X-ray fluorescence, quantitative X-ray diffraction and QEMSCAN™ to cross-validate the analysis. Certain streams were also put through a laboratory-scale Davis Tube Recovery washing process to produce clean concentrates for analysis. The QEMSCAN™ analysis identified various metallurgical characteristics (mineral association, particle sizes, grain sizes, particle densities, etc) and these were evaluated for each separation and comminution stage to both understand the processes involved and identify opportunities for improvement. Key findings from the investigation indicated the importance of understanding the elemental deportment of target elements throughout the various minerals. The standard practice of tracking iron deportment through assay provided misleading results on losses to tail through the plant. The investigation provided insight into both wanted and unwanted minerals and the efficiency of each separation stage. The efficiencies of separation are critical due to their impact on downstream capacity, and the investigation provided insight into where opportunities exist to extract more benefit. The findings of the geometallurgical analysis have been implemented on the concentrator, and improvements in the rejection of non-magnetic minerals have been seen.CITATION:Gerber, J, Stanton, C and Olwagen, D, 2015. Using geometallurgy during process optimisation activities at the Southern Middleback Ranges magnetite concentrator, in Proceedings Iron Ore 2015, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Fidler

Underground coal gasification (UCG) is a process by which coal is converted in situ to a combustible gas that can be used as a fuel or chemical feedstock. The process has been used in commercial-size projects in the former Soviet Union for more than 40 years, while significant national research programs have been undertaken in the United States and Western Europe. The Chinchilla UCG project is located at a site southeast of Chinchilla in Queensland. The UCG operation commenced in December 1999. A controlled shutdown of the process was initiated in January 2002 and successfully completed in April 2003. The process is currently under conservation and ready for restoration of gas production for commercial use in the near future. Groundwater plays an important role in the gas formation process during UCG. Most of the process water required for chemical reactions is usually derived from the coal seam itself and from surrounding aquifers. If insufficient water is available for chemical reactions the UCG gas will contain reduced concentrations of combustible components, and conversely, excessive water influx into the process area would cool down the reactor and thus limit the energy available for gas production reactions. Because of the importance of groundwater in the gasification reactions, and the potential to contaminate groundwater if the process is not correctly controlled, it is essential to predict and to control the groundwater influx into underground gasifiers during and after underground gasification. Control of groundwater requires a thorough understanding of hydrogeological conditions in the vicinity of the gasifier in order to be able to predict inflow rates, and constant monitoring throughout the process of water production rates and groundwater pressure in the coal seam and adjacent aquifers. Hydrogeological testing and groundwater monitoring in the vicinity of the UCG operation commenced six months in advance of its initiation. Monitoring of groundwater pressures in the vicinity of the gasifier have also been undertaken using vibrating wire piezometers installed in the coal seam at varying distances from the gasifier. This paper presents the results of the hydrogeological testing and groundwater quality monitoring carried out at the site, which show that it is possible to operate a UCG process without uncontrolled impacts on groundwater.

Jan 1, 2003

By M Haest, O Dominguez, D Mittrup

Technological innovations and emerging analytical capabilities are transforming the way drill samples are analysed, with real-time mineralogical analysis made possible. In addition, new business/technical requirements are challenging long standing processes to incorporate more sources of information during planning in order to improve compliance to plan during mining and processing. Unfortunately, the new sources of information that are added do not always have adequate protocols in place to ensure quality data is collected.Spectral data covering the visible – near – short wave – midwave – longwave range are routinely collected by the Geoscience and Exploration department at BHP Billiton Iron Ore for accurate mineralogical identification. These data are used for geological interpretations (logging and modelling) and prediction of physical variables (metallurgical and geotechnical properties).This paper introduces how sampling and quality assurance / quality control concepts have been applied in the spectral data process. The described routine for sampling, data collection/management and reconciliation has been developed to track system precision and accurately and consistently ensure the data is of high quality before it is used across the mining chain.CITATION:Mittrup, D, Dominguez, O and Haest, M, 2017. A new approach to implement quality assurance and quality control to technological innovations – quality of spectral data capture and processes in the minerals industry, in Proceedings Eighth World Conference on Sampling and Blending , pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By S Doyle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Macraes gold mine in Otago, New Zealand, is developed along the central portion of the Hyde-Macraes Shear Zone (HMSZ), which dips gently to the NE, and is traceable over 30 km of strike, before disappearing under tertiary cover. Mineralisation is most intensely developed along the hanging wall shear, which defines the upper limit of the shear zone, although significant packages of quartz vein arrays and mineralised shears occur sporadically beneath the hanging wall shear.The Macraes gold mine is now in its 25th year of operation, well beyond the projected mine life at the time of commissioning in 1990, and currently contains over triple the measured and indicated resource inventory that was defined at start up. The extended mine life and resource growth has been driven by exploration and resource development success, efficient low-cost mining and processing, improving gold price, as well as an ethos of continuous improvement.The emphasis of Oceanagold’s exploration and resource development has shifted over time; from hanging-wall-focused mapping, soil sampling and step-out drilling, through exploitation of previously drilled stockwork mineralisation, to the pursuit of blind, higher-grade underground targets.Mineralisation within the HMSZ remains open at depth, and the regional potential has not been fully tested. Given the relatively low-grade of gold mineralisation at Macraes, the consideration of tungsten as a supplementary co-product provides an exciting opportunity.CITATION:Moore, J and Doyle, S, 2015. Resource definition in the world-class Macraes gold mine, New Zealand, in Proceedings PACRIM 2015 Congress, pp 557–564 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007

By C E. Woolley, A Hosseini, J Foster

Northern Star’s Thunderbox Open Pit C-Zone cutback was designed to maximise extraction in a short life excavation; In fresh rock on the western wall this included 20 m to 30 m bench heights with 6.5 m to 10 m berm widths and a 90° pre-split angle. Rock mass quality in this area is generally fair to good, however, there are sections where the dominant foliation runs parallel with the designed pit wall, and more closely spaced, altered, foliation is present: these areas are difficult to predict and prone to failure. Stringent controls and monitoring were required in order to safely access below these areas, in particular the use of slope stability monitoring radar, Trigger Action Response Plans (TARPs), re-entry procedures, visual inspections, drone inspections and day-to-day personnel awareness of the hazard. Robust and comprehensively planned remediation was also required after two significant slope failure events where long reach equipment and rope access techniques were utilised to remediate the areas in question safely, but also in a timely manner, such that expected production targets were impacted as little as reasonably practicable. This combination of rigorous risk management and well planned remediation resulted in a successful and complete extraction of the C-Zone cutback with no impact to operational safety.

Jun 22, 2022

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of chromite ores with sodium carbonate. Results of tests conducted in a laboratory furnace indicated that the sodium carbonate reacted rapidly with part of the gangue material to form a metastable intermediate that later reacted further with the chromite. For the conditions used, the recovery of water-soluble sodium chromate was able to be described empirically as yield % = a tn with a = 0.24 T - 241.3; n = 3.90 - 3.12 × 10-3 T and t is the reaction time in hours.The major rate limiting step in the overall reaction sequence appears to be the rate at which oxygen can get to the reaction sites across the liquid film coating the solid reactants.Sodium sulfate alone was found to be an unsatisfactory source of alkali for reaction with chromite. However when limestone also was added in quantities sufficient to allow the reaction CaCO3 + Na2SO4 + H20 ? Ca SO4 + 2NaOH + CO2 to take place, the results obtained were comparable to those found when sodium car-bonate was used.For chromite particles in the size range -124 + 105 µm, the use of stoichiometric excess of sodium carbonate did not appear to increase the yield or the reaction rate significantly. However, with smaller sized particles, - 53 µm, increased yields of water-soluble chromate were obtained when roasted with more than the theoretical quantity of sodium carbonate.

Jan 1, 1984

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

By S Talu, E Savage, S Howe

Major falls of ground, strainbursts, airblast and mudrush events are the major hazards in block caving environments, resulting in both safety and financial consequences and losses. Rio Tinto mines have developed strategies to reduce the likelihood of these events occurring. However, until recently, there have been no tools available to monitor and manage these hazards in real time.Mira Geoscience and Rio Tinto have collaborated to develop real-time geohazmaps to monitor and manage major cave hazards. These geohazmaps are used by mine planners to integrate multiple hazard parameters that contribute to form a combined hazard rating.The benefits of implementing geohazmaps include safety and cost improvements through the early identification of potential locations for major events. These cost savings are realised in the design phase, where development and critical infrastructure is located in areas of lower hazard rating. Additional improvements can be achieved by taking the hazard level into consideration when planning the production and development schedules and ground support design.CITATION:Talu, S, Savage, E and Howe, S, 2016. Geohazmap implementation in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 817–822 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A Purton, C Taylor, E Conroy

The spatial modelling of geometallurgical domains is an important step in the characterisation of an ore deposit allowing for the quantification of various rock types, their differing rock properties and the overall value of a project. The traditional approach to modelling such features is through the use of deterministic models, where a single estimate of the extents and structure of the ore deposit is mapped out by geologists based on available data and their interpretation of the geological processes. Any uncertainty in the layout of different domains is not accounted for and heterogeneities of chemical and physical properties of the orebody are likely underestimated. Spatial machine learning techniques can be used to derive geometallurgical categories, or classes, from multiscale, multiresolution and high dimensional measured rock properties. Subsequently, geostatistical simulations of these classes can be applied to obtain multiple equiprobable realisations that define the layout of the geometallurgical classes at unknown locations between boreholes, or domains. In-turn these realisations can be used quantify the uncertainties in the location of boundaries between different domains. The development of a workflow for defining geometallurgical domains and later geostatistically simulating them across the Orebody H; a complex stratabound Bedded Iron Ore deposit located in Western Australia’s Pilbara region is demonstrated. This could be used to identify zones of high uncertainty where collection of additional data might help mitigate or minimise risks and in turn improve forecast production performances.

Mar 22, 2022

By D Maconochie, S Pradhan, M Reed

The Waterview Connection will provide a high-quality strategic alternative to State Highway One and complete Auckland’s Western Ring Route connecting State Highways 20 and 16. The project includes twin three-lane motorway tunnels 2.4 km long and 13.1 m internal diameter (ID). The tunnel construction started in November 2013 using the tenth largest earth pressure balance (EPB) tunnel boring machine (TBM) in the world. The tunnels will pass beneath urban and greenfield areas as well as a major local arterial road. The project is being delivered by an alliance of constructors, designers and the New Zealand Transport Agency. This paper describes some of the key innovative and cost saving design solutions that have been achieved through collaboration in the alliance environment with the construction team, owner’s verifier, the segmental lining precast suballiance and the M&E suballiance for the underground works. The key design elements of the tunnel comprise a three-lane roadway, invert culvert and backfill, precast segmental lining, sixteen mined cross passages including a low point sump cross passage and steel segments for opening to the cross passages. This paper reviews interdisciplinary design integration and the economies achieved in the permanent works tunnel lining design, including reduction in lining thickness and optimising reinforcement, cross passage separation of 150 m, efficient design of the invert culvert and backfill design, main drainage pipe and low point sump. The paper also describes the attributes of the TBM and the invert culvert construction methodology.CITATION:Pradhan, S, Maconochie, D and Reed, M, 2014. Tunnel design in an alliance for Waterview Connection, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 425–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Franklin, C Puglisi, S Fitch

Implementation of a well planned and executed Management Operating System (MOS) can result in widespread improvements to operational performance but its success relies heavily on the investment by and engagement of the larger workforce with the project. Over the seven month period of the Telfer MOS project, significant improvements were achieved; a 20% increase in monthly hoisted tonnes from the open stope and sublevel cave operations and a 45% increase in square metres of ore extracted from the narrow vein operation. The Telfer MOS was undertaken with the intention that the project wasn’t solely about producing new tools, it hinged on the investment and behaviours of the personnel affected by these tools and alterations. To ensure that the project ran smoothly, the Byrnecut senior leadership team and their operators were heavily involved in the project’s development. In the initial stage, Telfer’s MOS project determined that the quality and accuracy of the information received in the form of radio calls to mine control and completed operator plods was questionable. This required an overhaul of the data collection and verification process in the form of altered operator plods, which was then cross referenced with the operator’s radio calls to mine control. Once the data collection and verification process was implemented, the Telfer team was then able to produce several tools with the aim of providing visibility to the data being captured and its implications. These tools allowed the mine foremen to determine whether equipment was being under-utilised and where they should focus their production efforts to meet monthly targets. Whilst the initial underground project is now complete, the implementation of MOS across the entire site is ongoing with significant operating improvements occurring.

Mar 15, 2021

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024