Search Documents

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By M Malec, J Szczerbinski

Hazards in underground mines are concomitant with the mining of mineral deposits and have their source in a minerÆs work environment. The authors of the paper have undertaken a trial classification of these hazards into three groups, depending on the sphere of their occurrence:lithosphere, ie rock mass, atmosphere, ie air in mine workings, and technosphere, ie machines, equipment and facilities in mine workings. The lithosphere creates such hazards as bumps, rock outbursts, the atmosphere is a factor causing fires, methane explosions and climatic hazards, whereas accidents concomitant with an operation of machines and equipment occur in the technosphere. Assuming that the number of accidents in the mining industry, concomitant with hazards, reflects the degree of safety, it has been shown, that in Poland they are under control to a large extent.

Jan 1, 1999

By Hogan C. J

The compact BWE system set up in 1984 to mine ironsand dunes and the underlying ironsand-clay has been an effective high volume produc- tion unit for New Zealand Steel Mining Ltd at the Waikato North Head ironsand mine. The system utilising two compact S400E (0 & K) Bucket Wheel Exca- vators and a single shared Beltwagon for transfer to the shiftable bench conveyors replaced a fleet of mobile elevating scrapers when the produc- tion requirement was increased by a factor of six. A key factor in favour of the BWE system was the economic advan- tages of low unit costs for both manpower and electrical energy.

Jan 1, 1989

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

By A B. Christie, R Barker

Recent studies carried out to support the development of a strategy for the New Zealand mineral industry by the NZ Minerals Industry Association have included investigations of mineral potential, and the development of scenarios for realising this countryÆs mineral potential by 2010. New economic research is applying a general equilibrium model to quantify the opportunity cost of this potential. The model analyses separately four categories of land (private land and three categories of Crown land) and identifies four distinct mineral classes û precious metals, industrial minerals, coal and aggregate. It investigates the economic effect of the increased availability of mineral resources on the mining industry itself, on other industry sectors and on the NZ economy generally, including its impact on unemployment, GDP and household welfare.The analyses suggest that increases in the level of GDP of between 1.9 per cent and 3.4 per cent may be obtained by utilising New ZealandÆs mineral wealth to varying degrees. The mineral industry sectors are significant beneficiaries under all scenarios; mineral output increases by between two and five times its current level. However, the flow-on effects to the rest of the economy, and to households, are also significant. The analyses show that household income, adjusted for changes in consumer prices, can be expected to increase by between 1.6 per cent and 2.7 per cent. This results largely from increased employment.

Jan 1, 2002

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

By JSrvinen A, Yll÷ E

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By J Rayner, R P. Langmead, J A. R Coote

Gosowong is situated within the Neogene magmatic arc of Halmahera island in the Maluku province of eastern Indonesia. It was discovered as the result of a rigorous ground reconnaissance program in an area with no previous mining activity. The broad structural setting in the Gosowong District comprises an elongate dome formed by the forceful upward intrusion of magma along a deep-seated structure, resulting in associated tensional fracturing trending parallel to the long axis of the dome. Four copper-gold porphyries and numerous low-grade epithermal veins occur within this mineralised corridor, with the Gosowong Deposit being the only economic occurrence discovered to-date. Gold mineralisation is hosted within multiphase epithermal quartz-adularia and quartz-chlorite fissure veins, breccias, and stockworks. High-grade gold mineralisation is emplaced in two gently south-plunging ore shoots along a 400 m section of the north-striking, east-dipping, Gosowong Fault, the primary control on mineralisation. The Gosowong Fault is believed to be a tensional fracture associated with uplift of the dome. Lithological variation and structural intersections play a large role in grade distribution within the vein zone. Host rocks comprise a wide range of shallow marine, intermediate-basic volcanic and volcaniclastic rocks of ?late Miocene age. The Gosowong gold deposit is a classic example of a low-sulphidation epithermal gold deposit, based on the abundance of adularia and illite in the alteration assemblage, and low base-metal sulphide content within quartz-adularia veins. The indicated resource is estimated at 0.99 Mt at 27 g/t Au and 38 g/t Ag for a total of 870 000 ounces Au, using a cut-off grade of 2 g/t Au.

Jan 1, 1999

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

Since the days of Adam Smith and Milton Friedman the discussion of corporate citizenship and sustainability has been flooded with multiple contradictions, with proponents of sustainability saying that it is a crucial cog in the business strategy, while those against, maintain that æthe business of business is businessÆ and therefore sustainability issues are just add-ons. Sustainability arises from a deeply held vision by corporate leaders that businesses can and should play a role beyond just making money. Businesses should embrace the understanding that everything that a company does has an impact both internally and externally (communities, employees and customers), and the natural environment. This paper highlights the approach that led to a view that there is a contradiction between profitability, sustainability and community development, and we provide a further argument to the contrary. This argument is based on a comprehensive literature review of over three decades by various scholars linking corporate social performance and corporate financial performance. Driefontein Gold MineÆs approach is that of linking the community development, natural environmental and employee well-being initiatives and projects to the mineÆs business strategy. The paper further highlights the coordination and implementation mechanism of sustainability at the mine where the accountability lies with the head of the mine operations. A two pronged approach is employed where there is an internal dialogue on sustainability between the various departments coordinated by the sustainable development department and an external tri-sector partnership with local government, interested and affected parties and the mine. These approaches are closely linked to the contributions towards the mineÆs financial bottom line.

Jan 1, 2009

Rock bolting provides a supplement or alternative to conventional timber and steel supports. The tensile strength of the bolts lies within a range established by manufacturing quality control. Rock bolt testing determines the ability of the rock, anchor and individual bolt as an assembly to accept load. The.test is performed to the yield strength of the bolt or anchor and deflection is observed. The anchorage index, inches deflection per 1000 lb load increment, is a measure of anchorage quality. This allows comparison with anchorages under ideal conditions. It also permits comparative assessment of roof bolt anchors in a particular environment.

Jan 1, 1971

By Collins BJ

Basic principles of stack injection are outlined and supported by calculations of thermal, chemical and aerodynamic requirements of an ideal 4000 tpd furnace. Calculated results show that these requirements vary with conversion of FeO, and that best performance may be expected with XFeO = 1.0 for which calculated production is 6919 tpd and coke rate is only 211 kg/thm. Calculations are also presented for a cycled injection. Discussions show that stack injection is a good way of overcoming softening problems and meeting the demand for iron in a fluctuating demand situation when it exceeds the maximum capacity of a furnace.

Jan 1, 1975

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By H S. Smit, P Lotz

Gold mining companies who are signatories of the International Cyanide Management Code (visit www.cyanidecode.org for further information) are required to measure WAD cyanide on-line and destroy WAD cyanide in excess of specified limits. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5 such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Recognising and in response to the gold mining industryÆs need for an on-line WAD cyanide measurement device, Mintek recently developed the WAD Cynoprobe. The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide from metal-cyano complexes. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand <-> Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The instrument proved to be accurate and reliable in the laboratory as well as under industrial gold plant conditions during various trials. It has gained wide-spread commercial acceptance both locally and internationally. However, itÆs recent exposure to complex ore types have called for refinements to the analysis technique. It has been further developed to improve its precision and accuracy and to remove reagent and thiosulfate interferences. Its compatibility with the most commonly used destruction oxidants has also recently been investigated. The WAD Cynoprobe may be configured to measure both free and WAD cyanide concentration. Its fast analysis time, approximately 5 min, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. Proper oxidant dosage control and monitoring of effluent concentration levels will ultimately result in less cyanide and post-destruction salts discharged into the environment.

Jan 1, 2008

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987