Search Documents

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By S Mundell, A Atkins, S van de Water

Geoscientific information management enables the capture, management and delivery of the original geoscientific observations and measurements of the earth’s natural resources. However, original observations and measurements are worth nothing if the quality and integrity of the data can’t be guaranteed. Geoscientific information is one of the fundamental assets enabling miners to make confident and accurate business decisions, whether that is defining a resource model, performing reconciliation, delivering ore reserve reports or meeting environmental compliance requirements. Without access to reliable, validated or verified data it increases the risk of miners using incorrect information for reporting and compliance. Industry codes, such as JORC, or government regulations, such as environmental compliance requirements, must be adhered to and companies should be able to confidently report to these standards. Without having a robust information management framework in place, it becomes a challenge to make trustworthy decisions, report confidently and reduce the risk of non-compliance. As a key initiative, good data governance should form one part of a miner’s information management strategy. Within the mining industry it is common for companies to only consider technology tools as the key focus for compliance whereas a mature information management focus will additionally consider people and process. All three pillars are critical for a miner to have confidence in their data driven decisions. This paper discusses an industry framework for best-practice geoscientific information management based on the observations gathered from analysing data management practices within the mining industry. It focuses on how the three pillars of people, process and technology are crucial elements to improve operational decisions and ensure companies are compliant.

Nov 8, 2021

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Connelly

Silver and gold bearing ore from the Troy Resources NL Casposo Gold-Silver Project, located within the San Juan Province of Argentina contains a complex mix of gold, silver, electrum and silver sulphides in the ore. Casposo is a typical low sulphidation epithermal style gold–silver deposit where mineralisation is hosted within rhyolite – andesite flows and breccias. Veins are typically banded quartz–chalcedony colloform - crustiform banded with quartz - carbonate infill. Mineralisation is associated with an assemblage consisting of quartz, chalcedony, adularia, calcite, illite, sericite and trace sulphides. Gold and silver occur as electrum, native silver, sulfosalts and silver sulphides. This paper presents a case study that describes the process selection, development and engineering of a tailored process plant for the recovery of gold and silver from this ore.The original feasibility study, modelling, metallurgical testwork and engineering studies are outlined. The final flowsheet was based on minimising capital cost, operability, recovery and minimising technical risk.The process flowsheet uses the traditional Merrill Crowe route because of the high silver to gold ratio in the feed and achieves maximum gold and silver recovery while providing a common facility for future ore body treatment.

Aug 8, 2011

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M Binks

The Fosterville Gold mine is located approximately 20km to the East of Bendigo in central Victoria. The gold at Fosterville occurs as solid solution within disseminated arsenopyrite and pyrite. The Fosterville ore bodies contain various amounts of native carbon in the form of bituminous coal. This carbon (Non-Carbonate Carbon or NCC) has been the predominant mechanism for gold loss from the processing facility through”preg-robbing”.Processing of the Fosterville ore is achieved initially through crushing, grinding and flotation to extract the sulphides. The sulphide concentrate is oxidized using Bacterial Oxidation, before being leached in a conventional CIL circuit. A high portion of the native carbon (NCC) in the mine ore is naturally hydrophobic in nature, and subsequently reports to the flotation concentrate stream, and ultimately onto the CIL circuit. This NCC has a notable preg-robbing ability. Treatment of Black Shale ores, which have elevated NCC levels, has historically resulted in CIL recoveries as low as 35%, with around 60-80% of the gold loss from the leach circuit attributed to preg-robbing.Standard technologies for dealing with a carbonaceous leach feed have been trialed with limited success. The discovery of the significance of heat on leach recoveries, triggered extensive testwork on a range of leach feed and tails samples. Pilot plant testing demonstrated that “Heated Leaching” of the CIL tails was the best process with an average recovery increase of 7.5% being achieved. Following a successful pilot study, an engineering feasibility study was completed by Minerva Engineering, and the project economics determined. With strong recovery gains evident and a predicted project payback of 1-1.5 years, approval for the installation of the full scale plant was granted. Detailed design commenced in September 2008 with installation commencing in January 2009. The circuit was successfully commissioned in April 2009.Following commissioning, the Heated Leach circuit has achieved recovery gains of 4-14%, and has proven itself to be a significant contributor to the overall plant performance.

Aug 8, 2011

By Y Peng, C Burns, Y Mu, R A. Lauten

In both laboratory flotation experiments and from analysing the composition of the lead concentrate at the Boliden Tara lead-zinc mine in Ireland, it has been found that F-250 may replace cyanide as a pyrite depressant. Replacement or reduction of the cyanide consumption is highly desirable from a safety perspective given the toxicity of cyanide. Scrutiny of results from the plant trial indicate that F-250 is less efficient as a cyanide depressant when the flotation feed contains high levels of pyrite. Statistical analysis of the results does not capture this trend, illustrating a need to collect more data at higher pyrite ore levels. A recent model proposed for biopolymer-induced pyrite depression is reviewed and discussed next to the suggested mechanism for pyrite depression via cyanide. Review of the interactions causing pyrite depression point to different manners in achieving depression. In light of the less efficient F-250 pyrite depression at high pyrite levels, it is speculated if the two depressants may act synergistically at high levels of pyrite in the feed. CITATION:Lauten, R A, Burns, C, Mu, Y and Peng, Y, 2018. Pyrite depression at Boliden Tara using F-250 – a biopolymer, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By E C. Holloway

"The financial valuation of mining assets has a number of fundamental differences to the valuation of many other asset groupings. One such difference is that typically, the greater proportion of both the cost and revenue sides of the cash flow are inherently governed by systemic market forces.As a result, the range of outcomes for the valuation of each mining asset is more unpredictable, with higher levels of risk and uncertainty. In contrast, the management function of many other non-mining businesses or industry groups can control at least a portion of the cash flow by maintaining the margin or controlling the sales price. The management teams of mining businesses and operations typically have limited options, and are thus price-takers for both costs and revenues. As mining is an inherently cyclical industry, large, long-life operations can exist through several price cycles, making valuation both subjective and challenging.The outcomes of both static- and stochastic-based valuations, as well as the internal probabilities of the associated cash flow statements, are significantly impacted when the correlations between the appropriate parameters are quantified, modelled and incorporated into the valuation framework. The appropriate parameters for correlation modelling primarily include those that are governed by systemic market forces. Applying this process results in a different risk profile for the asset by allowing the risks resulting from systemic market movements to be more accurately quantified and then objectively minimised. This process also reduces the level of residual uncertainty in the valuation outcome.This paper presents a valuation methodology to pragmatically incorporate this level of valuation sophistication and statistically quantify the associated increase in the level of confidence of the valuation outcomes reported.CITATION:Holloway, E C, 2016. Correlated valuation methodology, in Proceedings Project Evaluation 2016, pp 181–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By E K. Chiw, S-M Jung, S M. Masuka, ika

The world reserves of high-grade iron ore have depleted necessitating the need to utilise any existing natural iron ore deposits to meet the demands of the world’s expanding economy using hydrogen in the reduction process to curb CO2 emission. These low-grade ores include iron ores with high phosphorus content. The thermodynamic conditions in the blast furnace allow for the reduction of phosphorus that readily dissolves into the molten iron. Phosphorus in the gaseous state readily dissolves into the molten iron and therefore must be removed due to its negative influence on the mechanical properties of steel. The removal of phosphorus from molten iron is difficult causing the phosphorus to concentrate in metallic iron. The aim of this study is to provide basic knowledge on the phosphorus distribution after reduction using the CO-H2 and possibly provide the optimum conditions for phosphorus partitioning into slag, increasing the probability of its removal by magnetic separation. Total porosity, pore size distribution and surface area of the pellets used were measured using a mercury pressure porosimeter. The reduction was carried out using thermogravimetric analyses (TGA). The reduction rate increased with increasing H2 and was highest when 100 per cent H2 was used. Metal elements distribution in the reduced pellet was clarified using electron probe microanalysis (EPMA) and showed that phosphorus was distributed in the same areas as Ca. More phosphorus was concentrated in slag when 50 per cent CO–50 per cent H2 was used, increasing the probability of dephosphorization using magnetic separation. The concentration of phosphorus into slag was related to the rate of reduction. Further investigations into the reduction kinetics of this ore by CO-H2 is suggested to validate these findings. Nevertheless, a comprehensive thermodynamic analysis of the reduction of phosphorus containing phases found in iron ore with carbon, CO and H2 was provided to assist in selecting the optimal reduction experimental conditions.

Sep 18, 2023