Search Documents

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.' It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.' The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.' The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

By Gilbert Doan

AN extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, spon-sored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to

Jan 1, 1936

By F. S. Norcross

Manganese has long been considered one of the United States' most important strategic raw materials. Its indispensabil-ity in steel manufacture makes it vital to the nation's industrial life. Coupled with this indispensability is the fact that domestic producers have not been able as yet to supply more than a small part of the nation's manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is consumed in the form of ferromanganese, an alloy that averages 80 per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevailing prices. Dependence upon foreign sources thrust the United States into serious difficulties during the World War. At the start of hostilities in 1914, the nation was obtaining about four-fifths of its ore from the Eastern Hemisphere. Domestic production had been negligible, amounting to only 3000 to 7000 tons a year. As the war continued, shipments from the East, endangered by sea attack and blockade, dwindled rapidly. Imports from Brazil mounted. In this grave emergency, the United States, starting almost from scratch and under the stimulus of high prices, succeeded by 1918 in producing a peak of 3II,000 tons, about 35 per cent of its consumption that year. Since the war, the United States has depended upon foreign sources for more than nine-tenths of its high-grade ore. During 1936, 1937 and 1938, imports for consumption averaged 736,000 tons a year. During the same period, domestic shipments averaged 21,000 tons a year. Of the imports, the U.S.S.R. accounted for an annual average of 280,000 tons, the Gold Coast 208,000 tons, India 74,000 tons, and Brazil 72,500 tons. But India and Brazil, which in 1936 ranked third and fourth in the list of importers, were displaced in 1937 and 1938 by a new and much nearer source—Cuba. From less than I per cent of United States imports in 1931, the island republic increased its shipments to more than 27 per cent in 1938. Cuba's average for this three-year period was 97,000 tons, and its total for 1938 was 131,000 tons. History The story of the economic development of manganese in Cuba dates back to the Spanish-American War days. John Green-way, then one of Theodore Roosevelt's

Jan 1, 1943

By C. M. Shigley

Tan record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.1 The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 t0 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000000-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation-the largest known magnesium plant utilizing sea water as its raw material. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and y miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1945

By W. A. Anderson, R. F. Mehl

RECRYSTALLIZATION of cold-worked metals has long been known to proceed by a process of nucleation and growth.1 When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.' Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrystallization is thus analyzed into its two component rates.2 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;* values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of N and G over appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson' have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,' have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

In response to Dr. Ledoux's paper, a large number of metallurgical establishments and individual assayers expressed their willingness to co-operate in the plan he proposed. The necessary samples were prepared as follows : Matte.—A car-load of matte was put through a Blake crusher, then automatically subdivided into tenths by a Taylor and Brunton sampler, and one-tenth passed through Cornish rolls and through a 12-mesh screen. This was again subdivided by an automatic sampler into tenths, and a final tenth, representing 1 per cent. of the original lot, was finished by hand-sampling on an iron floor until 100 pounds remained. This was pulverized to pass a 40-mesh screen and then thoroughly mixed and divided in the presence of my assistant for distribution to the parties co-operating. Copper Borings.—These were taken from a lot of anodes, the dip-samples from several batches having been united, remelted and cast into a plate, which was proved by assay to be of uniform quality in its different parts. Borings from this plate were intimately mixed and divided in the presence of my assistant. Samples were sent out November 1,1894, with the following letter: New York City, November 1, 1894. Samples of matte and copper (about I pound each) carefully prepared in the presence of my assistant and sealed with his seal as below, are sent you by express for assay and report according to the plan of Dr. Ledoux. These samples are constituted about as follows: Matte. Copper. From. To. From. To. Copper, per cent.,.....50 60 ..........., Gold, oz. per ton,.....2 3 0.20 0.50 Silver, oz. per ton,.....100 150 140 180

Jan 1, 1896

By Robert W. Fullerton, Barry G. McMillan, Donald T. King, Henning E. Soderberg

INTRODUCTION Dust control in coal preparation and related transport is a multi- faceted problem which must be anticipated whenever dry, fine coal is subject to rough handling which can disperse it in the air. This problem can be minimized by careful planning and proper design, by eliminating procedures which maximize dust production, and by utilizing the most appropriate dust-collection "hardware" for a given situation. Proper maintenance after dust-collection systems are installed is also very important, and will not only enable the selected equipment to perform properly, but will also reduce component wear, recover valuable product with the highest efficiency, provide cleaner and safer working conditions, and allow local clean-air standards to be met. This chapter is designed to provide basic information about dust control in relation to material processing and handling during coal preparation. Areas discussed should provide the reader with insight into basic dust-collection theory, particle behavior, equipment types, ductwork and hood considerations, general maintenance and design planning, and the economics of dust collection. Because of the wide range of areas covered and the various specialized problems inherent in each, the text is organized to be a practical reference, and not a complete, unabridged treatise of ventilation and dust-control design. Nevertheless, the information presented should be of value in both understanding and reducing problems of dust control in coal preparation.

Jan 1, 1979

By J. L. Gillson

IN a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. GENERAL STATEMENT ON FLUORSPAR SITUATION Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in I901 for $5.81, in 1916 for $5.92. When the United States entered World War I, fluorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $I8.00 per ton. By 1935 the average price had fallen to $15.00, but in 194o with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, 'or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. [ ] Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be- again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1945

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By V. C. Allison

Large-scale testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparntion of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments conducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have becn reviewed by the Bureau of Mines.' The Bureau has conducted many tests with the Frazer-Cle1ncnt5 apparattus, which gives the pressures set up when the dust cloud within is ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. Need for a Dust-testing Apparatus An attempt has been made to design an apparatus that may be used for checking and correlating the expcrimental tests. The first design was a wooden gallery, 8 by 10 in., inside cross section, and 12 ft. long, and having a number of strips along each side for creation of turbulence. The wooden gallery did not get beyond its period of calibration; it mas difficult to make the gallery sufficiently tight, for it was necessary that the top be removable in order that the gallery could be cleaned. In the use of the wooden gallery, however, sufficient operating data were obtained to be a guide in the design of a steel gallery having a circular cross-section. One of the features was a flap valve, at the closed end of the gallery, that would open inwardly thus preventing a reduced pressure within, caused by the cooling of the gases of combustion, and the explosions propagated much better than when the valve was not used; another feature was the determining of the best method for getting a cloud of dust simultaneously in all parts of the gallery, which was accomplished by the use of the concussion wave of a small quantity of powder or by the use of compressed air.

Jan 1, 1927