Search Documents

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By McQuiston. F. W., E. C. Tveter

Sulfide mineral flotation has been applied to all naturally occurring sulfides and several synthetics. Of even more importance is the fact that economic separations are now being made between sulfides of essentially all the different metals. The variety of methods and minerals involved in such practice make it difficult to characterize them except in terms of general factors which influence the practices used. Ore grade and mineral composition are the major factors determining the processing method and the extent to which processing must be carried to achieve optimum economic return for a given ore. Since the choice of treatment is also affected by such factors as mine location, shipping charges, smelter schedules, each ore is a separate problem even though mineralization may be similar; The dissemination of minerals in the ore naturally determines the fineness of grind required for liberation. However, since grinding costs are a major part of most milling costs, emphasis has been placed on means of rejecting gangue minerals at the coarsest size possible. This has led to increased flotation of middling products or bulk concentrates for subsequent regrind and retreatment. Reagent development has also played an important part in present plant practice. Relatively few new frothers and collectors have found application during the past 25 years and many have disappeared. In general practice, re- agent combination choice is now fairly consistent with the type of collector being chosen on the basis of the mineral to be floated, the frother on the basis of pulp alkalinity, and the modifiers primarily on the basis of minerals to be rejected. REPRESENTATIVE FLOTATION PLANTS The milling operations described in this chapter have been selected primarily to illustrate these differences in ores and processing methods for the major types of ore minerals. The compositions of these minerals are shown in Table 1. These concentrators were chosen as representatives, both on the basis of geographic location and mineral content of the ore treated. At least one mill is included from each of the major producers, but the primary object was to show the practice employed for the various ore minerals and the different approaches to the middling problems encountered. The individual plants which have contributed data to this study are listed in Table 2, with a summary of their operating data, and are discussed in the order shown.

Jan 1, 1962

By T. A. Rickard

From time immemorial the fissure-vein has been held the simplest type of ore-deposit. The prominence given to it by Cotta and his disciples, from their study of the mines of the Erzgebirge, is impressed upon technical literature; and, in consequence, the ores which carry the valuable metals have been supposed to occur mainly in fissures, cleaving the rocks in diverse directions, and the noblest type of vein has been deemed that which cut across the country independent of its structure, whether evidenced as bedding, foliation or cleavage, and which was identified with rents produced in the rocky crust of the earth. As so conceived, the vein was a fissure filled with ore, extending through the country for a varying distance, and continued downward to a depth more or less proportionate to its longitudinal extent. The vein-material was bounded by an encasement of rock, and those immediate surfaces which limited it on either aide were called " walls." These primary conceptions have become modified by the experience of modern mining in widely separated regions. The study of lode-formations has led to the recognition of notable departures from the supposed normal structure of the veins of Saxony and Cornwall, the two classic homes of early economic geology. Typically the walls of a vein are conceived as parallel rockplanes enclosing the ore; the upper one being called the " hanging-," and the lower the "foot-wall."* Walls are rarely alike. Even where a vein traverses a homogeneons formation, such as a massive crystalline rock, it is usually found that the surface which bounds it underneath

Jan 1, 1897

By Earl F. Hanson

Fires in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of $61,996,719. General Layout of the Mine The No. 2 shaft, which is the main working shaft of the Tintic Standard, is within the main orebody and is connected with the five other shafts. Their respective positions with respect to the No. 2 shaft are as follows: North Lily, 2770 ft. northwest with drift connections on the 700 and 900-ft. levels; No. 3 shaft, 670 ft. east connected through the 700-ft. level; Eureka Standard, 4550 ft. south, connected on the 900-ft. level; No. 1 shaft, 1470 ft. southwest, with connecting drifts on the 900 and 1250-ft. levels; Eureka Lilly, 2000 ft. southwest, with connecting drift and raise through the 1250-ft. level. The Tintic Standard orebody consists essentially of one continuous oreshoot extending from the 600-ft. level to the 1450-ft. level, with a cross-sectional area of approximately 70,000 sq. ft. at both top and bottom, reaching a maximum area of 215,000 sq. ft. between the 1100

Jan 1, 1937

By R. F. Decker, J. R. Mihalisin

Phase transformations in a series of relatively pure nickel-titanium-aluminum binary and ternary alloys were studied. The purpose was to clarify age-hardening mechanisms, especially in predominantly titanium-hardened compositions. The micro-structures, as determined on a tirne-temperature-transformation basis by light and electron microscopy and X-ray diffraction, were correlated with room temperature and hot hardnesses. The stability of the ? phase under nonequilibrium conditions was shown to be important in this system. MANY of the alloys designed for service in the temperature range of 1200oF (649°C) to 1800°F (980°C) are austenitic iron-.nickel base alloys hardened by titanium and aluminum. The control of high-temperature properties of these alloys has been advanced by the knowledge of microstructures provided by the equilibrium diagrams of Taylor and Floyd1 and Taylor.2, 3 However, there have been notable instances in the predominantly titanium-hardened alloys where the correlation of properties with microstructure and the equilibrium diagrams has been unsuccessful. Mihalisin and carrol14 have noted in electron microscope studies of commercial alloys of this type that a fee phase precipitates and transforms to 71 (hep Ni3Ti) in stress-rupture tests. Bieber5 found that this fee phase remained in nickel-chromium-titanium alloys even when aluminum was excluded. Age hardening in iron-nickel base alloys has been attributed to 71 by Craver, Aggen, and Dyrkacz,6 ? (fee phase based on Ni3Al) by Beattie and Hagel7 and both phases by Lena,8 Yet, on the basis of the nickel-titanium-aluminum equilibrium diagram of Taylor and Floyd shown in Fig. 1, it has been difficult to understand the presence of ? in low aluminum alloys. Furthermore, the characteristic coarse dispersion of 71 has not been commensurate with the marked aging response. Also there have been anomalous grain boundary transformations in the iron-nickel base alloys which have markedly reduced notched stress rupture properties.9 These have been related to boron content and residual cold work. Recently, Golubtsova and Mashkovich,10 Buckle and Manene11 and Bogaryatskii and Tyapkin12 have noted a transition fee Ni3Ti in titanium-hardened nickel-base alloys. It was apparent from the latter studies that a transition phase was important in the nickel-titanium-aluminum system. The purpose of this study was to identify this phase, measure its transformation characteristics and kinetics, and attempt to correlate these findings with age hardening. It was believed that time-temperature-transformation studies, because of their adaptability to transition phases, would be of most value for this investigation. Accordingly, this method of study was undertaken on relatively pure nickel-titanium-aluminum alloys with controlled variations in boron content and residual cold work. EXPERIMENTAL PROCEDURES Compositions were selected from the nickel-titanium-aluminum isothermal section of Taylor and Floyd.' These compositions are plotted in Fig. 1 and were selected to obtain equal aging potential of approximately 15 pet by volume of the equilibrium precipitate. The materials were vacuum melted from

Jan 1, 1961

By John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 36 tons of water for each ton of coal produced, while bituminous mines average about 5 or 6 tons. Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. But it must also be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1973

By Hallet R. Robbins

Korea, the ancient" Hermit Kingdom," is a peninsula jutting out from the coast of eastern Asia. By the natives it is called " Chosen," nfhich, translated, means " Land of the Morning Calm." It lies between the Yellow sea and the Sea of Japan. On the north it is separated from Manchuria and the Russian province of Primorsk by the Yalu and Tiumen rivers; on the south the Korcan straits interpose a rough voyage of 120 nliles to the nearest point in Japan. The entire country is situated between the parallels of 34O and 42O N. latitude. The surface of the country is made up of successive ranges of ul~glaciated mountains, separated by narrow, fertile, and more or less densely populated, valleys. Through all the obscure centuries of its history, Korea has succeeded in maintaining a monastic seclusion, over which, from time immeniorial until the late Chino-Japanese war in 1894, China exercised a shadowy sovereignty. Although Korea had been forced into slight foreign contact previously, her first forcign treaty was signed with Japan in 1876. Under the restraining guardianship of China, the Japanese treaty bore but infiignificant innovations for Korea; but when, in 1883, a treaty was made with the United States, the first of the western nations, a decade after the American gunboats, under Commodore Rodgers and Lieutenant Schley, forced their may up the Salee river, Korea awoke from her sleep of 4,000 years. The Eorean peninsula suddenly became the arena where the enterprises and individuals of many foreign nations met in fiercest rivalry. Out of this struggle grew two singularly successful American enterprises, both of which have played an important part in developing the natural resources of the country. The first, and best known of these, is the Oriental Consolidated Mining Co., which was organized by Lcigh Hunt

Jan 1, 1909

By John Wulff, J. H. Hollomon

The opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was re-deposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May16 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to a1pha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,a in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As2O3),

Jan 1, 1942

By Herbert Haas

ChEap power is essential to large-scale mining and metallurgical operations, particularly where fine grinding of large tonnages has to be resorted to, as is the case with an increasing number of mines treating disseminated copper ores, or low-grade gold ores, in the grinding of which considerable power is consumed. A comparison of the cost of generating power with Diesel engines and steam turbines and a brief discussion of the different factors governing the profitable use of either type of prime mover may be timely in view of the importance of a cheap supply of power to the mining industry, and the prominence that has lately been given to Diesel engines in America. As many of our most important mines and largest producers of metals are located in sections where neither cheap coal nor water power is available, and the price of oil fuel is increased by long hauls, the Diesel engine will become a prime mover of increasing importance. This applies particularly to the Southwestern States, where an ample supply of cold water for condensing purposes is unusual and local climatological conditions interfere in securing the high vacua essential to high turbine efficiency. About 12 times as much water will be required for condensing purposes with steam turbines under general conditions as is needed for jacket-cooling of two-stroke cycle Diesel engines; four-stroke cycle Diesel engines require only one-twentieth of the cooling water. Another condition favoring the use of Diesel engines is the high load factor at which most mine power plants operate. The influence of load factor on the cost of generating power is shown in Tables 1. and 2 and in Fig. 1. The higher the cost of fuel and the load factor, the greater will be the proportion of the fuel to the other costs making up the total cost of generating power. Capital charges (interest and redemption), maintenance, operating labor, and lubrication are practically constant amounts regardless of the load-output of the station; the fuel consumption and its cost are practically the only variables with the load. The costs here given are based on conditions as generally found in the Southwestern States, and on Diesel engine operating experience in European countries, where this type of prime mover has reached a high state of perfection, units upward of 4,000 hp. having proved entirely successful in operation.

Jan 1, 1917

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

In a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress,t The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term ilfracture stress' has come into use with the same significance as 'ctechnical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens betqrcen yield and fracture, A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress s3 to the longitudinal stress S1.* The results of the experiments are represented by a series of their flow-stress curves for each Of the metals investigated, and these diagrams have been used for the development Of Other diagrams Of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not On the stress system, he was 'Orrect in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, "auld Seem to be axiomatic, provided that the flow Stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard Of this principle has led to some untenable theories Of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1949

By Michael F. Dunn, Francis S. Kendorski

The fall of rock from strip coal mine highwalls continues to be the largest single source of fatal accidents, so methods to improve highwall stability through improved blasting practices were investigated in the field. This paper covers the results of a project to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. Utilizing surface blasting concepts of trying to achieve flexural failure of the rock mass both horizontally and longitudinally by appropriate relationships between burden, spacing, and hole length, as well as delay time sequence to achieve optimal confinement and breakage, successful results were achieved. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. Actual blockfalls could be measured and the stability for each blast design thus quantified. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1983

By William H. Case

The Bertha zinc-mines of the Bertha Zinc and Mineral Company are in that part of the State of Virginia popularly known as Southwest Virginia, and are included in that division of the " Great Valley " named in recent years the " New River-Cripple Creek Mineral-Region of Virginia." The mines lie wholly in the southeast part of Wythe county, two miles from Pulaski county on the east, and three miles from Carroll county on the south. The only other zinc-mines that are opened in the region are those of Manning & Squier, which adjoin the Bertha zinc-mines on the northeast, and the mines of the Wythe Lend and Zinc Company, at Austinville, eight miles to the southwest. A little farther southwest of Austinville, near Ivanhoe, a new company is preparing to mine zinc-ores. The mining properties named are included within a distance of ten miles along a direct line, bearing north 55' east, on the south side of New river, which here flows northeastward in a tortuous course. The greatest distance of any of the mine-openings from the river is a little less than two miles. It is not the magnitude of the operations in zinc-mining in this particular region, as compared with that of other well-known districts, that merits especial notice. Aside from the exceptional purity of the spelter made directly from the Bertha ores, some peculiar features of the zinc-ore deposih, as shown at the Bertha mines, and

Jan 1, 1894

By Wilfrid R. Foster

The industrial importance of the sillimanite group of minerals depends upon the beneficial properties exhibited by porcelains and refractories in which substantial amounts of these minerals are utilized as raw materials. The presence of "sillimanite" (now known to be the closely related mineral, mullite) in conventional porcelains and refractories has been known since before the turn of the century. As early as 1906 German investigators observed a direct correlation between the "sillimanite" content of a porcelain and its electrical and mechanical properties. Acting upon this discovery, U. S. Bureau of Standards investigators during World War I developed improved pyrometer tubes and spark plug porcelains, by increasing substantially the amount of "sillimanite" at the expense of quartz. The success of these experiments, first reported in 1918, at once aroused a lively interest in the location of natural sources of sillimanite and its related minerals. As a result of diligent search, the large andalusite deposits in California were discovered in 1919. Within the next several years large deposits of kyanite and sillimanite in India and kyanite in the United States had been reported. The search for these minerals in quantity, by both private and governmental agencies, has continued unabated during the ensuing forty years. A number of domestic deposits of kyanite have been worked during the past 30 years. Of these, only the Virginian and South Carolinian deposits are currently in substantial production. The only commercial andalusite production in the United States has been in California and Nevada. A dumortierite deposit in Nevada, known since 1917 but ignored for want of a commercial use, began production in 1925. A topaz occurrence in South Carolina has yielded a small production since about 1940. Domestic production of andalusite, dumortierite and topaz had virtually ceased by 1950. There has never been any commercial development of domestic sillimanite deposits. Kyanite has been mined almost continuously in India since about 1922. The remoteness of the large deposits of Indian sillimanite had caused it to be neglected until 1949. In that year sillimanite production began, and it has continued to the present. South African andalusite has been marketed from the 1930's until the present time. From 1944 to 1955 Kenya, British East Africa, was an important producer of kyanite. Commercial deposits of kyanite in Ontario, Canada should soon be in production. The first production of kyanite in Europe began in Austria in 1953. No commercial deposits of mullite are known anywhere in the world. It is of interest to note that synthetic mullite, which as "sillimanite" first elicited interest in the A12O3-rich aluminosilicate refractories, has enjoyed a marked increase in production in recent years. This is a result of the gradual depletion of known deposits of high-quality kyanite and related minerals."' Composition The sillimanite group includes kyanite, andalusite, and sillimanite, all having the same chemical composition (A12O3•SiO2) but different physical properties. Two other minerals, dumortierite and topaz, are also included in

Jan 1, 1960

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By C Macquarie, Maurice Cook

Normally the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 mm., for example, would, for many purposes, be regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals arid alloy. that take place on annealing, and a number of generalizations have beell reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results. however that are not covered by these generalizations can be obtained, which, in some instances, may even appear to be contradictory to them. Xccortling to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which,

Jan 1, 1939

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By C.H. Lorig, M.C. Udy

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By M. C. Udy, C. H. Lorig

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938