Search Documents

By M. Gensamer

A RECENT paper1 described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected, by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in the present paper was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature A,, and (2) to attempt experimentally a demon-stration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper'.

Jan 1, 1936

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches 'carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on, this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable .to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, .and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By G. B. Walker, S. J. Swainson, S. A. Falconer, H. H. Vogel

During the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue of Mining and Metallurgy, Professor Taggart made the statement that " preconcentration by heavy suspension was Miss A.1.M.E 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery'.' have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By C. L. Magee, H. W. Paxton

The effects of testing temperature, frorn 77" to 420" K, and volume fraction of martensite on the micro-plastic response of unaged Fe-31Ni martensite-austenite aggregates have been determined. The kinetics of the aging phenomena which lead to a decrease in the microplastic response were also characterized. These determinations, supplemented by other experimental results, show that at least two mechanisms of plastic deformation give rise to the apparent softness of the quenched structures. Only one of these mechanisms is fully discussed in this paper The transformation of retained austenite to martensite during the application of stress leads, in specified conditions, to large microplastic strains. This deformation behavior cannot be described by normal transformation plasticity theory but is shown to result from the fact that stress-assisted formation of martensite is a possible deformation mode. The present results and further considerations of previous work lead to the conclusion that it is unnecessary to postulate a special work-hardening mechanism to explain the mechanical properties of unaged martensite. It is now generally accepted that dislocation motion can occur in many solids at stresses very much below the L'macroscpic" yield stress, e.g., 0.1 pct offset. This phenomenon has been investigated by a variety of techniques including measurements of elastic limit,' effective static elastic modulus,~ and irreversible deformation following stressing at low levels.3"5 Of particular interest to the work to be described are exper -iments conducted on the deformation of martensite in attempts to decide whether freshly quenched ferrous martensites are "hard" or "soft".6 Muir, Averbach, and cohenl and McEvily, Ku, and ~ohnston' have shown that as-quenched ferrous rnartensites can be plastically deformed at relatively low stresses. A difference between these two sets of experiments exists in that some diffusion of carbon would take place before testing in the experiments of Muir et a1. because the plain Fe-C alloys which they have tested transform to martensite well above room temperature. McEvily et a1. examined Fe-Ni-C alloys with Ms of about -30"~ and tested the alloys directly after quenching to — 195" ~ —a technique which obviates any appreciable carbon diffusion. Unfortunately, a characteristic of the alloys which transform below room temperature is that they do not transform entirely to martensite. The results discussed below will show that, because the transformation of this retained austenite under stress leads to plastic deformation, one cannot investigate the properties of martensite by such experiments. The existence of a second deformation phenomenon, which is not caused by retained austenite, is also established in the present work. In line with a previous suggestion,' it is believed that the second microdefor-mation mode is principally due to the internal stresses generated by the formation of martensite. To avoid confusion in the present report, the evidence we have found for this interpretation will be discussed separately in a brief note.7 EXPERIMENTAL Materials. The alloys were induction-melted and cast under vacuum; the resulting compositions are given in Table I. The ingots were hot-swaged to 2-in.-diam bar and further cold-swaged and/or cold-rolled prior to specimen preparation. The standard tensile specimens were machined from sheet. The gage section was 0.05 by 0.2 by 5 in.; 0.75-in.-wide ends had 0.2 5-in. centered holes for pinloading. The three-point bend samples were 0.075-in. thick and 0.6 in. bide. The distance between the outer loading points was 5.5 in. In order to establish a standard starting condition, all specimens were quenched to 77°K prior to annealing in vacuo for austenitizing. The temperature of the austenitizing anneal was controlled to + 5"~. The testing and aging temperatures were maintained by various liquid baths (nitrogen, 77"~; freon, 130° to 200°K; acetone, 200 to 300°K; silicone oil, 300' to 450°K) to better than il°K. Strain Measurement. The results herein were derived from both uniaxial tension and three-point bending experiments. For bending tests, the stresses and strains reported are those corresponding to the maximum fiber values. Normally, because of the small strains involved, very sensitive strain measurements are necessary to make microplastic measurements. However, because of the magnitude of the dilatation and shear involved in the martensitic transformation, the requirements in the present experiments proved to be less rigorous. In most experiments the plastic strain was evaluated by measuring stress relaxation and modulus defects. In this method, specimens are loaded rapidly to some predetermined load on an In-

Jan 1, 1969

MINING, to be precise, ends when the ore is delivered to a bin outside the mine. Usually the next step is concentrating; or, as it is more often called, milling. A few elementary definitions will help make clear the discussion that is to follow. A rock is an aggregate of minerals; copper ore is rock that contains copper-bearing minerals in quantity sufficient to make it profitable to mine and recover the copper in the form of marketable metal. Manifestly, under a literal interpretation, a mass of material might be copper ore one day and merely copper-bearing waste rock a week later, if the price of copper happened to drop in the interim. Emphasis already has been placed on the expansion that took place in the ore reserves of the Porphyry companies as a consequence of the great strides made in the technique of mining and ore treatment. So, even if one inserted a qualifying phrase, "at an average price for the metal," after the word "profitable," the definition would still be open to criticism. Place is another factor. It is evident that a body of excellent ore in Arizona might cease to be ore in the economic sense if it were moved intact to the interior of China. However, it is with ore in its technical and scientific aspect that this chapter is concerned. Speaking in general terms, the ton of Porphyry ore as it arrives at the surface contains 25 to 70 lb. of copper minerals in the form of disseminated particles or thin coats along fracture planes. When subjected to appropriate treatment this ton yields 12 to 40 lb. of metallic copper. These ranges take into account conditions of today and of 25 years ago. Two procedures are available: (1) concentration, followed by smelting of the concentrate, or (2) leaching and precipitation, usually by electrolytic deposition. Smelting and leaching are metallurgic processes in that they involve chemical change; concentration

Jan 1, 1933

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By H. Shaw

GRAVITATIONAL measurements made by means of the Eötvös torsion balance over any area enable a representation to be obtained of the total gravitational effects over the surface of that area arising from the combination of all sources of gravitational disturbance. The investigation of gravitational anomalies occurring in the upper layers of the earth's crust, in this way, has been attended with considerable success, and, especially in areas in which no undesirable disturbing factors were present, it has been possible to locate geological structures and mineral deposits with remarkable accuracy and also to delineate their confines and to indicate their depth below the surface with a certain amount of precision. Before this can be done successfully, however, it is necessary to determine the gravitational effect arising from all other extraneous .anomalies in order that these may be satisfactorily eliminated. Disturbing features giving rise to these gravitational anomalies may be divided into two classes, according to whether they are situated at or below the surface. The former are determined readily by a detailed leveling of the ground surface, and may be satisfactorily eliminated provided the specific gravity of the terrain material is known, but the latter are generally unknown, and can only be ascertained with difficulty. When, therefore, the observations obtained by means of the Eötvös torsion balance have been corrected for all surface irregularities, known as terrain and topographical effects, there remain residual gravitational values which are due entirely to subterranean conditions. The task of interpreting these results consists in disentangling the various subsurface anomalies, and subsequently in computing and recombining the effects of these various masses in order to verify the interpretation. When the gravitational anomalies are due to large and comparatively simple structures it is a matter of little difficulty to arrive at a satisfactory interpretation of the subterranean conditions, but in more complex areas, where the geological conditions are more complicated and several irregular features exist, the process of disentangling the various constituents of the complex mass arrangement is more difficult and requires the expenditure of considerable time and labor.

Jan 1, 1929

By P. A. Witherspoon, S. P. Neuman

Evaluating the permeability of a caprock overlying a potential gas storage reservoir is a very critical problem. Pumping water from the reservoir can be used as an evaluation tool in analyzing this problem. Fluid level changes that occur in the aquifer us well as in the caprock can be measured with appropriately placed wells. If the leakage of water from the caprock into the aquifer is considerable, the effects will be apparent in the aquifer. If the leakage is slight, however, it will not be possible to detect it with certainty from observations in the aquifer alone. Fluid level measurements in the caprock must be relied upon. and improved methods of analyzing such effects have been developed which are based on a theoretical analysis of fluid flow through a caprock of infinite thickness. An example applying these methods to field data is discussed. INTRODUCTION One of the most critical problems in evaluating an aquifer gas storage project is determining the tightness of the caprock overlying the formation to be used as the storage reservoir. A formation that has previously held oil or gas obviously has a suitable caprock, but an aquifer that contains only water gives no such assurance. A number of aquifer projects in the United States have been troubled by gas leaking out of the intended storage zone, and the ensuing difficulties have led to the development of new evaluation methods. One of these new methods is pump testing wherein water is removed from the aquifer at some controlled rate prior to injection of gas. This fluid withdrawal causes a pressure drop to move out through the aquifer for considerable distances in a matter of days or weeks. Depending on the properties of the caprock, a pressure transient can also pass upward (as well as downward) through the caprock layers adjacent to the aquifer. Thus, if the operator has placed observation wells at appropriate distances from the pumping well, the rapidity with which the pressure transients reach different points in the system can be used to investigate the fluid transport properties of both the aquifer and its caprock. The usefulness of pump testing has been recognized by groundwater hydrologists for many years as a means of determining the potential yield and properties of aquifers used in water supply They have introduced the term "leaky aquifer" for a system in which an aquifer is overlain (or underlain) by semipermeable caprock layers. The ease with which water leaks into the aquifer during pumping can, of course, be very beneficial in bringing additional water to the pumped well. Hydrologists have therefore devoted considerable attention to this prob-lem. From the gas storage standpoint, however, the tighter the caprock layers that overlie the intended storage reservoir, the better are the conditions for minimizing or eliminating any vertical migration of gas. Thus, after a suitable geologic structure has been found, the emphasis in aquifer storage projects is in determining that the caprock is tight. Attention has recently been focused on the use of pump testing as one approach to solving this problem.23,24 This paper presents a further development on evaluating the permeability of a slightly leaky caprock when the caprock is of infinite thickness. From the practical standpoint, this means that the caprock layers are thick enough that pressure transients do not reach the outer boundaries of the system during the pumping test. In a subsequent paper, an analysis of the case where the caprock is of finite thickness will be presented. PREVIOUS WORK ON LEAKY AQUIFERS Jacob" developed a partial differential equation describing the flow of water in an aquifer of permeability k that is overlain by a leaky caprock of permeability k'. Fig. 1 shows a schematic cross-section of the system under consideration. One of his principle assumptions was that if k > > k', the direction of flow is essentially vertical in the caprock and horizontal in the aquifer. Neuman19 confirmed the validity of Jacob's assumption using a mathematical model. Another assumption was that a permeable source layer overlies the caprock (Fig. 1) and is able to maintain a constant hydraulic head at the upper boundary of the caprock. By neglecting the effects of compressibility within the caprock, Jacob1* developed a solution for a bounded circular aquifer. Later, Hantush and Jacobx5 used the same assumptions to solve the case of an infinite radial aquifer that is pumped at a constant rate. Their solution may be expressed in di-mensionless parameters by

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By Richard P. Hight

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material, usually by rubbing action but also by impact (pressure blasting for example). They do not include abrasive tools, for instance, lathe tools and files--or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted al- though some chemical-action polishes and cleaners may also contain solid abrasives, for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded abrasive products such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cut- ting edges when grains become worn-for example: in garnet for sandpaper neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster that the ultimate cost will be less. It is for this reason that artificial abrasives have largely replaced natural abrasives. Abrasive Value Mineralogical hardness or "scratch" hardness as expressed in Mohs' scale is an important property in evaluating abrasive materials, but, as noted before, it is only one of several essential properties. The mineral hardness of pure crystal almandite garnet is about 7.5, but if the crystal is crossed by incipient fracture planes, or if it contains inclusions of other minerals, the apparent or useful hardness may be much lower. While the quartz grains in a sandstone have a hardness of 7, the bond holding the grains together may be so weak that the stone is valueless as a commercial abrasive. In artificially bonded wheels and stones, the hardness, strength, and character of the bond are fully as important as the hardness of the abrasive grains. Thus, in an overall consideration of abrasive hardness of loose abrasive grains, both "scratch" hardness and toughness must be considered. In naturally or artificially bonded abrasive stones, bond characteristics are a third factor, which is most important. The problem of abrasive hardness is further complicated by the inadequacies of methods of testing hardness and of expressing relative values. The Mohs' scale is inadequate both because the methods of testing are very crude and

Jan 1, 1975

OF the many categories into which scientific knowledge has been arbitrarily 'divided, the one that has proved most. applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry provide ample material on the principles of this subject for the student of steelmaking processes. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent, respectively the natural and the common logarithm of X. The two are related-by In X = 2.303 log X. Logarithms may, be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be helpful. MATTER Innumerable forms of matter may, be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas.. Whenever such a change occurs there is a corresponding change in the amount of energy associated with the matter. The process may require an input of energy, as in the electrolytic production of aluminum, or it may result in an output of energy, as in the combustion of fuel. The basic laws of the conservation of matter and of energy tell us that we cannot change the total amount of matter or the total amour t of energy.. When the fuel pile is used up, we realize that it has simply been converted into other forms of matter; .i.e., ash

Jan 1, 1964

By James W. Shaffer

Aluminum is the most abundant metallic element and forms 8% of the earth's crust. Because of its chemical activity it does not occur in nature in a metallic form but principally in the silicates, feldspar, mica, shale, and clay. Bauxitic raw materials-bauxitic clay, aluminous laterite, and bauxite-develop from these aluminum silicate sources. Bauxite and aluminous laterite are naturally occurring mixtures of aluminum hydroxides and mineral impurities, and they are the major sources of aluminum. End Uses Bauxite is the basic ore of the aluminum industry. It is refined into aluminum hydroxide and calcined for feed stock to electrolytic smelters. Over 90% of the tonnage mined is refined and smelted into aluminum. The total tonnage consumed by other industries is small in comparison, but bauxite and alumina are important for the manufacture of refractories, ceramics, chemicals, abrasives, pharmaceuticals, catalysts, cements, dessicants, and flame retardants. Some aluminum-containing industrial products are made from clays and other materials but the majority originate from bauxite directly or from aluminum hydroxide and alumina refined from bauxite. Lateritic type bauxite is also used as building and decorative stone. Geology Mineralogy and Properties Bauxite is a mineral raw material composed principally of one or more aluminum hydroxide minerals and impurities of silica, iron oxide, titania, and other elements in minor or trace amounts. The important aluminum hydroxide minerals are gibbsite, boehmite, and diaspore. Bayerite, nordstrandite, and tucanite are naturally occurring aluminum hydroxides but are rare and not commercially important. Mixtures of gibbsite and boehmite are common, boehmite and diaspore less common, and gibbsite and diaspore rare. Gibbsite is aluminum trihydroxide. Boehmite and diaspore are aluminum oxide hydroxides and have essentially the same composition, but diaspore has a greater hardness and a more tightly bonded and denser atomic structure. Although not technically correct, the commercial terms trihydrate and monohydrate are frequently used to distinguish types of bauxite. If bauxite is all or nearly all gibbsite, it is referred to as a trihydrate ore; if boehmite or diaspore or a mixture of both are the dominant minerals, the bauxite is called a monohydrate ore. If substantial amounts of both gibbsite and boehmite are present, the bauxite is frequently referred to as a mixed ore. Properties of major bauxite minerals are shown in Table 1. Silica, iron oxides, and titania are major impurities always present in deposits of bauxitic raw materials.. Silica impurities usually occur as clay minerals, micaceous minerals, or quartz, but cristobalite and feldspar are found in some deposits. The most common clay minerals are kaolins; however, illites and chlorites are often found in small quantities. Varying proportions of aluminum, iron, and clay minerals make bauxite, aluminous laterite, ferruginous laterite, and bauxitic clay deposits gradational with each other. Hematite and goethite are the common iron mineral impurities in many bauxites. Magnetite and ilmenite occur in deposits derived from basic igneous rocks. Other iron minerals associated with bauxite are maghemite, pyrite, siderite, and marcasite. The titanium minerals found in bauxites are anatase, leucoxene, rutile, ilmenite, titaniferous

Jan 1, 1983

By Daniel Martin

THE dendritic pattern of steels shown by deep etching is used exten-sively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in indus-try. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general character-istics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. PREVIOUS WORK Detailed methods for macroetching were outlined by Yatsevitch1 and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshian.2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed' and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions.

Jan 1, 1939

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948

By E. W. Davis

On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite. The magnetite comprises about 35 per cent. of the rock, the remainder being chiefly quartzite and iron silicates. The rock has a specific gravity of 3.4, a hardness of 7, and is extremely tough. This large deposit was located early in the history of the Minnesota iron-ore industry but has not been utilized because of its low percentage of iron as compared with the other Mesabi ores, and because of the difficulty and expense of any milling treatment that would concentrate the iron. An investigation, begun about 3 years ago, shows that the magnetit,e is finely disseminated throughout the entire formation and that there are bands or lenses of higher- and of lower-grade material, in which the magnetite and silicate are intimately mixed. As a result, the scheme of milling adopted must include a fine-crushing plant. As it is necessary to crush to 200 mesh in order to produce the desired grade of product, the fine crushing is one of the largest items of expense and for this reason has been given detailed study. It is the purpose of this paper to present some of the results of the work on fine crushing, as to both theory and practice. Previous to fine crushing the part of the rock that contains little or no magnetite can be discarded by magnetic concentrators after each reduction in size in the dry-crushing plant. This-makes it possible to fine-crush a minimum of rock and also establishes the feed to the ball-mill as below % in. The fine-crushing problem, then, consists simply in crushing the rock from 1/4 in. to 200 mesh at the minimum expense. Equipment of the Testing Plant In order to determine, among other things, the operating conditions of the ball-mill when working on this rock, a test mill of about 300 T. daily capacity was erected at Duluth, Minn. The fine-crushing plant contains a Hardinge 8-ft. by 22-in. (2.4-m. by 55.8-cm.) conical mill, a 6- by 27-ft. (1.8 by 8.2-m.) Dorr duplex bowl-type classifier, a 41/2-ft. (1.37-m.) standard Akins classifier, and the auxiliary machinery necessary to handle the products. Each machine is driven by an individual motor, each of which is provided with meters for measuring the power required. Over 150 tests have been made in the ball-mill, varying in

Jan 1, 1920

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By L. M. Pidgeon, P. G. Thornhill

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. lengtn of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of ¼ in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10o to 15oC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press Operating at a temperature of 140°C

Jan 1, 1958