Search Documents

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By W. L. Crentz, E. E. Donath, D. Doherty

IN 1948, the United States used nearly six million barrels of petroleum products every day. Although substitution of synthetic fuels for the natural petroleum product is not here yet, large quantities of special-purpose coal will be required in ever-increasing volume as the domestic production of oil from other sources fails to meet demand and the production of synthetic fuels begins. Petroleum economists do not agree as to when the shortages of domestic oil will appear; but the increasing per capita consumption of oil, coupled with a constantly growing population drawing on a potential domestic oil supply estimated to be 85 billion barrels, sooner or later will result in demand exceeding domestic supply. When this situation comes about, the excess demand will be either eliminated by curtailment of consumption or the demand met by increasing importation of foreign oil or by the production of synthetic fuels. The first recourse would definitely retard the heretofore unbroken rise in American living standards, while dependence upon a foreign oil supply during a war or other emergency would be dangerous. On the other hand, the enormous coal reserves in the United States, plus sizable deposits of oil shale, indicate adequate means of augmenting a diminishing domestic oil supply. Some idea of the impact of an expanding synthetic liquid fuels program on the coal-mining industry may be gathered when it is considered that to supply just half of our present-day petroleum needs synthetically from coal would increase the coal output by about 500 million tons annually, using an 11,900 Btu bituminous coal as the plant feed. If either a subbituminous coal or lignite were used, the quantity required would be materially increased. Synthetic Fuel Processes: The principal synthetic fuel processes using coal as a raw material are the Bergius, or coal-hydrogenation process, and the Fischer-Tropsch, or gas-synthesis process. These two processes not only produce different end products, but the preparation of the coal used in each presents its own individual problem to the coal-preparation engineer. The hydrogenation process brings together a mixture of dry, finely powdered coal, catalyst, and heavy oil to form a paste. Addition of hydrogen under rather high pressure and temperature conditions brings about transformation of the coal to a liquid product, from which a high-grade gasoline and other motor fuels may be obtained. The Fischer-Tropsch process requires the production of synthesis gas, a mixture of carbon monoxide and hydrogen. At the Bureau of Mines Louisiana, Mo., demonstration plant, this gas is being made by reacting dried pulverized coal with carefully controlled volumes of oxygen and superheated steam. After purification and in the presence of the proper catalyst and suitable conditions of pressure and temperature, the hydrogen and carbon monoxide components of the synthesis gas react to form motor fuel. The two processes are not competitive but rather com-

Jan 1, 1951

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By E. E. Donath, W. L. Crentz, D. Doherty

IN 1948, the United States used nearly six million barrels of petroleum products every day. Although substitution of synthetic fuels for the natural petroleum product is not here yet, large quantities of special-purpose coal will be required in ever-increasing volume as the domestic production of oil from other sources fails to meet demand and the production of synthetic fuels begins. Petroleum economists do not agree as to when the shortages of domestic oil will appear; but the increasing per capita consumption of oil, coupled with a constantly growing population drawing on a potential domestic oil supply estimated to be 85 billion barrels, sooner or later will result in demand exceeding domestic supply. When this situation comes about, the excess demand will be either eliminated by curtailment of consumption or the demand met by increasing importation of foreign oil or by the production of synthetic fuels. The first recourse would definitely retard the heretofore unbroken rise in American living standards, while dependence upon a foreign oil supply during a war or other emergency would be dangerous. On the other hand, the enormous coal reserves in the United States, plus sizable deposits of oil shale, indicate adequate means of augmenting a diminishing domestic oil supply. Some idea of the impact of an expanding synthetic liquid fuels program on the coal-mining industry may be gathered when it is considered that to supply just half of our present-day petroleum needs synthetically from coal would increase the coal output by about 500 million tons annually, using an 11,900 Btu bituminous coal as the plant feed. If either a subbituminous coal or lignite were used, the quantity required would be materially increased. Synthetic Fuel Processes: The principal synthetic fuel processes using coal as a raw material are the Bergius, or coal-hydrogenation process, and the Fischer-Tropsch, or gas-synthesis process. These two processes not only produce different end products, but the preparation of the coal used in each presents its own individual problem to the coal-preparation engineer. The hydrogenation process brings together a mixture of dry, finely powdered coal, catalyst, and heavy oil to form a paste. Addition of hydrogen under rather high pressure and temperature conditions brings about transformation of the coal to a liquid product, from which a high-grade gasoline and other motor fuels may be obtained. The Fischer-Tropsch process requires the production of synthesis gas, a mixture of carbon monoxide and hydrogen. At the Bureau of Mines Louisiana, Mo., demonstration plant, this gas is being made by reacting dried pulverized coal with carefully controlled volumes of oxygen and superheated steam. After purification and in the presence of the proper catalyst and suitable conditions of pressure and temperature, the hydrogen and carbon monoxide components of the synthesis gas react to form motor fuel. The two processes are not competitive but rather com-

Jan 1, 1951

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

AUGUST began with a reminder that warfare was still in progress in the world, in that the Greeks, still at war with Turkey, threatened Constantinople in spite of the small British and French forces of occupation and opened a vista of international dangers. There was in this, moreover, a recollection that religious questions in India had prevented the British from permitting a real settlement of the Turkish question, wherein the absence of Russia as a great power is missed. Civil warfare also continued in Ireland and China. Even in the military way the world is far from being at peace. Bloody fighting between the Fascisti (anti-communists) and the com-munists in Italy led to several provinces being put under martial law, but after a while these disturbances were quelled. In the latter part of the month the assassination of Michael Collins in Ireland produced a great shock. From China, however, there came rather favorable news, indicating the early reintegration of that country, which sooner or later ought to play an important part in world affairs. Economically, instead of there being any improve-ment, there grew a clearer perception of how bad things really are. Italian politics were in chaos through inability to find anyone to accept the premiership and assume the all but hopeless task of averting national bankruptcy. The French, too, began to see their own position in true colors, and especially to see how in reconstruction they had incurred debts on the strength of what they hoped to collect from Germany, with at last the understanding that the Germans could not pay and that France herself was thereby put in a desper-ate economic position. As for the Germans, them-selves their Reichsbank defaulted on ordinary bills early in August. As the month wore on the value of marks fell more and more and at the end it appeared that Germany was on the verge of economic collapse. On Aug. 7, another international conference (with America again absent) was assembled in London, this being the thirteenth since the war, and there was a general feeling that it would be the last. The prime question was what is to be done about the German reparations, but underlying was the whole subject of the entente. The conference opened like a meeting of importunate creditors, doubtful whether the debtor had any tangible assets. On Aug. 14 this conference broke up without coming to any useful conclusion. Indeed, the acrimony among the premiers was so sharp that even the entente between Great Britain and France was endangered. The international situation was saved only by the Reparations Commission excusing the Germans from the payment of 50,000,000 gold marks that come due on Aug. 15 But although the entente was nominally preserved there is no longer any illusion about the interests of Great Britain and France being different and that henceforth they will play their own hands. The London conference was really an effort to maintain the partnership, and it failed.

Jan 9, 1922

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By J. H. Jensen

Bromine is the intermediate member of the halogen family of elements between iodine, a solid: and chlorine, a gas. The name is derived from the Greek "bromos," meaning stench. Bromine is the only nonmetallic element that is liquid at room temperatures with a melting point of -7.2" C and a boiling point of 58.78" C. Reddish brown in color, it dissolves easily in water to yield a red solution. Bromine volatilizes at ordinary temperatures to a red vapor that is very irritating to the eyes, nose, and throat. Density of the liquid is 3.12 and gas weighs 7.59 gpl at standard conditions. As the element is highly active, it exists in nature only as bromide compounds. Bromine was discovered by Antoine Jerome Balard in seawater bitterns in 1826 and first prepared in quantity in 1860. Distribution Bromine is widely distributed in nature and compounds occur in solution in natural brines, in seawater, saline lakes, oil and gas well brines, and in evaporite chloride minerals. The concentration of bromine salts ranges from 60- 65 ppm in seawater to several thousand ppm in oil well brines and saline lakes. The distribution of bromine in marine evaporite minerals and in the solutions from which they crystallized was determined many years ago by H. E. Boeke (1 908). Theoretical aspects regarding the geochemistry of bromine have been published in numerous papers (Raup and Mite, 1969). Bromine occurs in solid solution in carnallite and sylvite associated in potash de- posits; in halite in salt beds; salt in oil shales; and in trona deposits. Its presence is useful as a guide in geochemical exploration. The analysis of small amounts of bromides in the presence of large amounts of chlorides is discussed by W. Schwerdtner (1963). Manganese, iron, and iodine may interfere with the determination. Other analytical methods are discussed at length in the literature (Stenger and Atchison, 1964). Sources and Reserves The sources and reserves of bromine, given in [Table 1], appear ample to meet present and foreseeable requirements in all producing countries. With the occurrence of bromine salts in sea-water and other brines, the potential for bromine production is worldwide. It has been estimated that 99% of all commercially recoverable bromine is in the ocean. However, actual subterranean brines having a higher bromine content than seawater will continue to be the preferred sources of bromine for the foreseeable future. Markets and Prices About 17% (1968) of bromine produced is used in its elemental form, with the balance consumed as bromides and bromates. The largest use for bromine is ethylene dibromide which, together with tetraethyl lead, are used as an antiknock additive in gasoline. Tetra-ethyl lead is the antiknock agent. Ethylene dibromide combines with the lead after combustion in the engine to form a volatile com- pound that escapes from the engine with the exhaust gases.

Jan 1, 1975

By J. F. Myers, F. M. Lewis

C. G. McLACHLAN*-I have read this paper with considerable interest and wish to congratulate the authors on the care with which they carried out their experiments and for the detailed sizing data they have presented. 011 the other hand I do not feel that these data establish their contention that "with other factors the same, the work accomplished in a fine crushing rod mill is directly proportional to the rotating speed." My reason for making this statement is that their conclusion is based on the percentage of minus 65 mesh material produced at each of the speeds at which their tests were run. The rod mill is, however, not a fine grinding machine and therefore figures based on minus 65 mesh production are figures outside the range at which it operates to best advantage. Further, if rod mill performance is to be judged on the production of such material it should have been established that a rod mill will produce it as effectively as a ball mill. To check this last point I have gone over some of the rod and ball mill grind-ing figures for our Waite-Atnulet operation and find that the ball mill at that property produces more minus 65 mesh material per horsepower than the rod mill. Moreover, this comparison is even more favorable to the ball mill if it is limited to minus 100 mesh production. It therefore seems to me that the most satisfactory basis on which to try to com-pare the performance of the rod mill in the present case is by taking a weighted average of all the new surface produced per horsepower. W. H. Coghill3 has published data which can be applied to the sizing figures presented by the authors, and if this is done the units of new surface per horsepower produced in the Tennessee tests are as follows: Admittedly the increment of increase in new surface per horsepower shown in the foregoing figures is not great, but its trend is nevertheless definitely in favor of slower speed operation, for the conditions under which these particular tests were run. I also feel that some information regarding liner contour should have been given as I think it will be found that a mill which is equipped with liners which lift the rod load can be run at a slower speed than a mill in which the liners are comparatively smooth. J. F. MYERS and F. M. LEWIS (authors' reply)—The position taken by Mr. McLachlan is to be respected even though we are all aware of the faults of surface considerations. As he points out. the increment of increase is very small. It is so small in fact that for all practical purposes it does not conflict with the conclusions of the paper. The authors appreciate Mr. McLachlan's comprehensive study of the data.

Jan 1, 1950

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By Oscar A. Glaeser

INDUSTRIAL relations in the United States Smelting Refining and Mining Company's Western operations covers the field of personnel and labor relations, and the principal aims are to render service to the employes of the Company and to its operating departments. Accident prevention Safety is a primary function. A safety engineer is employed at each operation. The wholehearted support of Company officials, staff, and the working force has been most successful in preventing accidents. Constant vigilance has been combined with a policy of building safety into all operating activities whether these are in the construction of a new facility, the developmnt of a mining system, or the direction of the working force. That this policy has produced results is attested to by the fact that the accident frequency rate at the Company's major mining operations in Utah has been reduced approximately 75 per cent in the ten-year period ending Dec. 31. 1946.

Jan 1, 1948

By Norman C. Stines

Russia's mineral potential is a secret that has been effectively kept by the Iron Curtain. There is no conclusive data and because of its extreme importance to the Free World, the subject is greatly discussed. Opinions range from those presented by Paul Tyler in his article "Russia's Mineral Potential," June issue of MINING ENGINEERING to those of Norman C. Stines, presented herewith. Mr. Stines is a consulting mining engineer of Los Gatos, Calif. He was in Russia, China, and Manchuria from 1909 to 1918 as a mining executive. From 1917 to 1919 he served as assistant military attache Intelligence Branch U. S. Army in Petrograd, Russia.

Jan 11, 1951

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By George H. Deike

UNDERGRADUATE interest in coal mining engineering has dropped to an alarmingly low level. Most companies having co-operative scholarship programs have been forced to abandon them for the duration.

Jan 1, 1944

By Julian E. Tobey

A MEMORABLE year has just passed in the field of coal utilization. Because of the war, oil conversions in industrial, commercial, and domestic installations have been made to the equivalent of 20,000,000 tons of coal. The war emergency has resulted in a great shifting of various types of coals to various markets. Huge tonnages of metallurgical-quality coals have been withdrawn from steam and domestic business and sent into the iron and steel industries. Marginal coals have replaced these coals in the steam and domestic field.

Jan 1, 1944

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By J. L. SCHUELER

THE writer has reread Mr. Ingalls' interesting article in the July, 1923, issue of MINING AND METAL- LURGY on "The Use of Spelter in Galvanizing." It seems that most writers, in commenting upon coatings of spelter on sheets and wire, dwell upon the thin coatings which these materials carry, and rightly so. However, they seem to forget that until very recently, in the case of wire, the manufacturer did not know how to apply a heavy coating of spelter to the wire, especially if the wire was to be woven into fence or fabricated in some other manner, because heavy coatings of spelter are exceedingly brittle. This is even true in the case of high-grade spelter, but to a lesser degree than with Prime Western. Because of this brittleness, it has been necessary for wire manufacturers to smooth the coating by passing the wire through tightly compressed wiping means of some kind, usually asbestos. This removes all of the excess spelter and allows only a thin coating to remain. The latter, as a rule, is malleable and the wire can be fabricated without material injury to the coating.

Jan 1, 1924

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.' In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found' that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.' There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.'0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969