Search Documents

By Jean Howard, E. V. Walker

ManY papers have been published during the last few years on the formation of cube texture in 3 1/4 pct Si-Fe, e.g., those of Assmus, Detert, Dunn, and Walter.1,5 All are concerned with the formation of the texture by a process involving secondary re-crystallization and the relative surface energies of (100) and other planes under certain conditions of annealing. The authors have found that cube texture can also be produced by heavily cold rolling strip in which the cube-on-edge texture has first been formed. Cube texture develops on annealing, but in this case it is not accompanied by secondary recrystallization. The starting material is a sintered compact, the preparation of which has been described elsewhere. Using a conventional processing schedule employed for producing commercial silicon-iron with the cube-on-edge texture, the sintered compact is cold rolled to such a thickness that, after annealing in pure hydrogen for 24 hr at 1350'~ to produce the cube-on-edge texture, the final thickness required can be obtained by giving a further cold reduction of 85 pct. Cube texture is developed by annealing at -900~~ in pure hydrogen: it has been produced in strip up to 0.024 in. thick. The microstructure of the strip consists of a mass of small primary grains within the boundaries of the much larger secondary grains which ex- hibited cube-on-edge texture before the final cold roll. If the strip is annealed at -1000 after the 85pct reduction, secondary recrystallization begins to take place, provided a strong cube texture is present. On raising the temperature more secondaries grow, complete secondary recrystallization being obtained on annealing at -1150'. From this it is concluded that the secondary crystals are produced by the texture inhibition mechanism: they show (110) and (111) planes in the surface of the strip, the former being the more numerous. It has been observed that the more perfect is the (110) [001] texture prior to cold rolling by 85 pct, the further from the ideal is the (100) [oo].] texture. A similar treatment applied to high quality commercial grain-oriented silicon-iron strip failed to produce cube texture. The tilt and rotation of the [loo] from the rolling direction was less than 10deg, but (to within a few degrees) the planes (130), (450) and (210) lay in the surface of the strip. Acknowledgment is made to the Engineer-in-Chief of the British Post Office for permission to use the information contained in this note.

Jan 1, 1962

Without having asked for it, the writer has apparently been drawn into the discussion regarding relative hoisting capacities which was started by Woodward Iron, egged on by Joe Haller of Cleveland-Cliffs [Mining Engineering, August p. 642] and Axel Kjelgaard [November p. 919], who took exception to Mr. Haller's remarks of tonnage hoisted and avers that they do better in Sweden. It does not appear to the writer that Mr. Haller was inclined to refer to the tonnage hoisted at Cleveland-Cliffs in a manner to imply that they claimed any hoisting record, but rather as a statement that they had hoisted a certain amount of ore during the year 1950. Mr. Haller has been in the mining game long enough to appreciate what Mr. Kjelgaard did not apparently take into consideration, that length of haul, shifts hoisted, nature of ore, method of loading and the many other factors which influence the hoisting cycle make a comparison of tonnages hoisted of two given mines almost an impossibility. Mr. Cheyette sent you .a copy of his letter to Bob Manegold relative to the capacities of the Orient #2 mine. There are several mines around the Country which constantly set up records about which little or nothing at all is ever heard. We cite the Snow Hill Coal Co. mine at Terre Haute, Ind., which has an automatic Nordberg hoist and which hoists 12 tons per trip or 700 tons per hr from 700 ft. This is a counter-weighted installation and a complete cycle is made every 62 seconds or 58 trips per hr. Another mine, The Potash Company of America mine at Carlsbad, N. Mex., has a Nordberg automatic hoist, hoisting eight tons per trip from 1150 ft on a one minute cycle. The materials hoisted in these two mines are ideal for automatic hoisting-they are free flowing so that no hang up is anticipated and hoisting is continuous. Multiplying out the above figures you will find that it is possible to hoist 11,000 tons in two shifts at Snow Hill or over 3 million tons in 300 days per year and over 2 million tons at Potash. Other mines have records which can be pointed to with pride. When a record for one year is established, it doesn't stand too long as here in America the ambition of all the men connected with the operation forces them on to larger tonnages. T. C. WIEDENHOEFER MANAGER MINE HOIST DEPARTMENT NORDBERG MANUFACTNRING CO. MILWAUKEE, WIS.

Jan 1, 1952

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By S. S. Clarke

THEN sufficient ore has been blocked out on a lease to warrant a shaft, the proposed. Location of the shaft should be carefully considered, as the old promoter's method of sinking wherever his hat landed is a sad mistake as some: of us have learned by trying to operate such mines. In some instances certain conditions exist, such as mill location, railroad right of way, etc., that necessitate a change of location from the. ideal, but under average conditions and with the knowledge of the formation gained from the drill logs and with the general trend of the orebody known, the shaft can be located from. the standpoint of its future relation to the mine with re-gard to hauling and' hoisting a maximum tonnage: at a minimum cost per ton, also taking into account the minimum amount of expense and trouble- in sinking. Quite a few shafts are located in the wall of a run or just in the thin edge of the orebody: As a general rule the formation here is solid and permits rapid and safe sinking, and the shaft pillars are left in practically valueless material. This permits the withdrawal of pillars and still keeps the shaft protected. By opening a shaft in thin ground, you are not tempted to cut it high, wide, and handsome, but to shape it up-with ample clearance for lay-bys and with more of an idea of permanency, as a few hundred extra dollars spent around the shafts for proper track installation will re-turn, a good rate of interest in ease of handling "cans," quick get-away; and fewer wrecks. Nearly all the shafts in this district are sunk on a contract basis, the con-tractors furnishing all labor and explosives, and the company building the sinking-derrick, dump-track, and furnishing, all equipment, material, and power. The following costs are the averages, for three shafts sunk through good solid formation, with no water to, contend with, and approximately 260 -ft., deep, having about-100 ft. of shale. The contract price was $9 per foot with the shale and $13 per foot in the solid, making a total of $2,980 paid to the contractor. The wages paid by the contractor were, $5 per shift for the hoist-man, who also sharpened steel, $6 for the lead shaft man, and $5 for the helper;, the cribbing was sawed on contract for 40c. per shaft: foot; about. 94 board feet. of cribbing was used per foot of staggered cribbing and 168 board feet per foot of solid cribbing.

Jan 8, 1928

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By AIME AIME

A CORPORATION would go into bankruptcy if its affairs were conducted as are those of the state of New York, according to the Committee on New York State Government Reorganization of the American Engineering Council of the Federated American Engineering Societies, in a report to the chairman, of the Joint Judiciary Committees of the Senate and Assembly. The report, just made public, was signed by the three members of the committee who were appointed by Herbert Hoover. They were H. de-B. Parsons, chair- man, Paul G. Brown and Lewis B. Stillwell. Although the American Engineering Council is a national organization, it decided to aid in governmental reorganization in New York State because of the magnitude of the task. The Council's committee in its report urged the passage of three state reorganization amendments for consolidation of departments, an executive budget system, and a four-year term for the higher state officials. In the words of the report :

Jan 1, 1921

By C. S. Smith

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhard Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Post-President; John Chipman, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretory. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman- Dennis Carney John Chipman J. C. Fulton J. H. Hollomon H. H. Kellogg, A. E. Lee, R. Moddin, J. D. sullivan, and D.' Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. lnstitute of Metals DM lion: Robert Maddin, Chairman. F. Lincoln Vogel, Jr.. Vice chairman. W. A. Backofen R. W. Boliuffi J. H. Bechtold' M. B. Bever R: S. Busk C 6. Goetzel poul Gordon C. D. Grobom, Jr., Robert F. Hehe-mann R. I. Joffee F. i. Joumot Jr. lrvin R. Kromer, A. J. Leno. Horold Morgolfn, C. J. McHargue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman. T. B. King, F. C. Laogenberg, W. O. Philbrook, and T. 0. Winkler. Publishod bimonthl by the American Institute of Mining Metollurgicol and Petroleum Engineers Inc., 29 West 39th Street, New York 16, N. Y. Telephone: PEonylvanie 6-9220. Subscription $20 par yew for non-AIME members in United States and North, South and Control Americo $25 foreign; $5 for AIME members. Single copies, $4.00, single copios foreign $5,00. The AIME is 1958 by the Amarican mode or opinion axpressed in it* publications ... Copyright by the Amarican lnstitute of Mining, MataIlurgicol, and Petrolum Engineers, Inc,. . . Reg. istered cable address AIME New Yark ... Indexed in Engineering Inderx, Industrial Arts ...Index and Chemicol Number5. Absrtracis . . . Second class postage paid at New York,Indor. N. Y., Industrialond Ann Arbor, Mich.

Jan 1, 1959

By L. G. Jones

The objective of this paper is to present a better method for determining reservoir reserves of gas from extended drawdown test data. Means are proposed for conducting the test with or without the requirement of prior build-up to a static reservoir pressure. The test is based upon solutions to unsteady-state gas flow developed in an earlier paper and is believed to be superior to previous methods for determining reserves from flow-test data. The limitatiom of such tests are discussed, with emphasis on the subject of test duration. The test can supply useful information if the mechanics and limitations of it are understood. This type of information can be particularly valuable in deciding whether or not to drill offsets to producing wells. INTRODUCTION In the life of any gas or oil field, the engineer in charge must decide if certain wells need stimulation and whether or not to drill more wells in the field. Well production tests can aid in making these decisions. For instance, the value of stimulation can be estimated by determining formation permeability and the amount of well damage from drawdown or build-up tests. These tests are freely used in the oil industry. A less well-known type of analysis uses data from extended drawdown tests for determining reservoir reserves. Into this category fits the "reservoir limit test" of Jones,'-3 and the "reservoir reserve test" presented in this paper. The chief value of these tests is their ability to "see" reservoir boundaries and thus prevent costly dry holes. Methods for determining reserves of both gas and oil reservoirs were proposed in the work of Jones. His proposals appear sound for single-phase liquid flow. The generality of his work on gas flow is open to question, however, since the analysis is based upon solutions to liquid-flow equations. The test for gas reserves presented here is derived from unsteady-state gas-flow solutions presented in a previous paper.' In deriving this reservoir reserve test, it has been assumed that all of the reservoir energy is provided by expansion of the reservoir fluid and that the reservoir is radially symmetrical. No mention has been made of the effects of deviations from Darcy's law such as quadratic (turbulent) flow and well damage. Since the terms representing these effects are function of rate only, since the rate is constant and since the data are plotted in a differential form, it seems reasonable that these terms will not affect the test results in any way. No attempt has been made to estimate the effects of water drive, faults, or other departures from an idealized and isolated reservoir. For a qualitative discussion of some of these effects, the reader is referred to a paper by Jones3

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A'-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B'-Vapor Transport Cooling- Termination of the `A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C'-Liquid Cooling--The `B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted' from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

By J. David Lowell

For his contributions to the field of mining geology, a striking example being his brilliant inte.rpretation of the complex geologic history of the San Manuel District (Pinal County, Arizona) which resulted in the discovery of the Kalamazoo orebody, and for his lecture, "Copper Resources in 1970." On a low desert ridge six miles south of Cairo lie the remains of the world's earliest known mining town, Maadi of predynastic Egypt. Copper artifacts, including ingots and an ax head which was spoiled in casting, indicate that copper ore was smelted in Maadi, and radiocarbon dating has placed the activity at least as early as 3300 B.C. This is the oldest documented date for the use of smelted copper, the first industrial metal used by man. Copper was mined and smelted almost as early in Asia Minor and on the island of Cyprus, but the greatest development of the budding copper industry was in Egypt, where specific historical records show that about 10,000 tons of copper metal were produced in the period from 1850-1580 B.C. Contrast this production of 35 tons per year with the present world production of about 7 million tpy. Evolution of the Copper Industry The copper ore mined by the ancients was high grade, and the copper produced was expensive. The copper industry began with narrow high-grade veins, but has evolved to the point where massive earth-moving equipment can be operated in huge, low-grade open pits. Indian pits dug before 3000 B.C. in the Lake Superior district were in ore which averaged 15% Cu. His- torical research done by Arthur Brant has shown that copper cost in the Middle East in 1840 B.C. in terms of 1970 labor dollars was about $25 per lb. The copper mined in northern Europe in 1540 in the time of Georgius Agricola averaged about 8% Cu, and the cost in 1970 labor dollars was about $10 per lb. Average ore grade had dropped to about 6% Cu in 1890, and the cost of copper in the U.S. in 1970 dollars was about 45¢ per lb. Butte, Mont., was a good example of the efficiently operated vein mines of this time. In 1906, Daniel Jackling made a dramatic entrance into the copper scene with the Bingham Canyon open-pit copper mine and proved that more profit was possible mining 2% porphyry copper ore on a

Jan 1, 1971

By Y. C. Liu

THE existence of mechanical twins in bcc metals has long been known. With recent intensive interest in the mechanism of twin formation and its role in plasticity and crack initiation, a study of the general Characteristics of twin intersection appears pertinent. The scope of the present note will be limited to the crystallography of the twin intersections of (112) twins, without consideration of its mechanism, movement of atoms, crystal structure, or the strain energy involved at such an intersection. The twinning elements of (112) twins are considered to be K1 = {112}, n1 = (111) and K2 = {112}, n2 = (111) with a twin shear of 0.707. The crystallographic features of twin intersections have been worked out in detail by Cahn.1 The present work applies the general principles postulated by Cahn to the intersections of (112) twins. The basic conditions for the twin intersection are: 1) The trace of crossing (A) and the secondary (C) twins in the planes of the crossed twin (B) must be parallel. 2) The direction (n1) and magnitude (s) of shear must be identical in the crossing and secondary twins. Also the sense of shear must be the same. These two conditions have to be fulfilled in order to maintain geometrical continuity at the twin interfaces. Fig. 1 shows the perspective representation of how these two conditions are fulfilled at the intersection. This type of intersection will be named Type-I. It is the purpose of this note to point out the existence of another type of intersection, Type-II, as shown in Fig. 2. In this type of intersection, the crossing twin A remains straight and the crossed twin B has been bent. The two conditions laid down by Cahn must also be met. This leads to the following corollary conditions: 1) The interface between twins B and C must be parallel to the twin habit of crossing twin A. 2) n1c must be parallel to n1A. 3) The twin shear (s) of twin C must be exactly equal to and in the same sense as that of crossing twin A. Thus, in order for the Type-II intersection to take place, the twining elements of secondary twin C must fulfill the above three conditions with respect to crossing twin A. Let K1 of crossed twin B be (112). All indices of the matrix can therefore be converted into new in-

Jan 1, 1963

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and' Morris Cohen,' and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955

All the Technical PUBlications and Preprints published in 1932 are available at Institute headquarters. They are also on file in public, university and technical libraries and, when so indicated in the list, may be found in the Transactions. Copies of the Technical Publications have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Insti-tute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of Preprints may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. Metal Mining Technical Publi- Title Author Meeting Trans. cation Volume No. and Page* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 88. 95 F.52 Shaft. Butte. Montana (13) Feb.. 1932 487-A.46 Progress in the Improvement of Max H. Barber New York. Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932 Milling And Concentration 445-B.37 Soap Flotation of the Nomulfides Will H. Coghill New York. H.19 (18) J. Bruce Clemmer Feb., 1932 461-B.38 Principles of Flotation—An Experi- I. W. Wark New York. mental Study of the Effect of A. B. Cox Feb.. 1932 Xanthates on Contact Angles at Mineral Surfaces (48) Iron and Steel Division 447-C.81 Electrochemical Potentials of Nitri- Shun-ichi Satoh New York, fied Steels (31) Feb.. 1932 450-C.82 Reaistanoe of Iron-aluminum Alloya N. 9. Ziegler New York. 100, 267. 670 E.143 to Oxidation at High Tempera- Feb., 1932 tures (8) 451-C.83 Pressure Welding of Low-carbon C. H. Austin New York. Steela with Theoretical Con- W. S. Jeffries Feb.. 1932 siderations on the Mechanism of Such Welding (42) 453-C.84 Inclusions—Tbeir Effect, Solubility C.E.Sims New York, 100, 154, 176 and Control in Cast Steel (24) 0. A. Lillieqvist Feb., 1932

Jan 1, 1932

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962