Search Documents

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

By W. Rostoker, R. P. Elliott

TWO intermediate phases enter into equilibrium with the primary solid solutions of titanium.' The TiMn2 phase was identified by Wallbaum2 as of the C14 type isomorphous with MgZn2. Contrary to Maykuth, et al.,¹ the phase occuring at about the 50-50 atomic proportion has been shown to derive from a peritectoid reaction.:' A 30 day anneal at 900°C of an alloy containing 52 wt pct Mn developed sufficient of the new phase to give a clear and predominant diffraction pattern. The powder pattern was taken in a 14 cm diameter powder camera using filtered Cu Ka radiation. In all, 75 lines were recognized and measured. Interplanar spacing and observed intensities for the first 26 of these are given in Table I.

Jan 1, 1954

By P. Nicholls

THOUGH the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more com-mon types. No new investigational data are included, but the deduc-tions are largely based on a recent publication of the U.S. Bureau of Mines1. DEFINITION OF TYPES There are three primary types of fuel beds: (1) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in .which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed hori-zontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1935

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By Robert Bakish, William D. Robertson

AFTER more than fifty years of investigation and continuing failure in service, a satisfactory mechanism to explain stress corrosion cracking in homogeneous alloys is still lacking. The relative chemical activity of grain boundaries and adjacent grains, inferred from the boundary structure, has been used to explain intergranular cracking in a brass.' This concept is probably correct as a general hypothesis, but it requires much more extensive development in order to explain satisfactorily the observed phenomena. For example, the specific function of the solute in an alloy must be considered, because intergranular failure does not occur in pure metals,' which are structurally similar to homogeneous alloys. Also, in this connection, an inter crystalline fracture path in binary copper alloys can be changed to a transcrystalline path by relatively small ternary additions.' The fracture path in ß brass is predominantly transcrystalline,' in contrast with an inter crystalline path in a brass. Whether the two different fracture paths are the result of a difference in composition, crystal structure, or the state of long range order is unknown and cannot be determined with ß brass, because only the ordered state can be obtained at room temperature. The study of chemical activity at structural sites in the Cu-Zn system is restricted by the formation of opaque films in an ammonia environment in which stress corrosion cracking is generally observed. Furthermore, both components of the alloy are chemically active and the interpretation of observations is therefore relatively complicated. The Cu-Au system is a better choice for the purpose of studying structural factors. In particular, CuAu is very susceptible to cracking in ferric chloride and opaque films are not formed in this solution; it may be obtained in different states of long and short range order; and, finally, only copper is oxidized in dilute ferric chloride, which considerably simplifies the chemical problem. To provide information necessary for a more general explanation of stress corrosion cracking in homogeneous solid solutions, the following structural factors have been investigated in a Cu-Au alloy having a composition corresponding to Cu,Au: 1) the effect of long and short range order; 2) the structural sites from which copper is removed from the annealed and cold worked polycrystalline alloy; and 3) the effect of annealing time and temperature on structural reactions in the cold worked alloy. Experimental Procedure A Cu-Au alloy of nominal Cu3Au composition was cast from cathode copper and high purity gold and fabricated into sheet and wire. Chemical analysis for copper and gold indicated 48.92 wt pct Cu and 51.01 pct Au. Quantitative spectrographic analysis indicated 0.01 pct Ag, 0.002 pct Pd, 0.001 pct Pb, and 0.002 pct Fe, with traces of magnesium, silicon, and zinc. Presumably most of the remaining 0.055 pct corresponds to the limits of analytical precision. Heat treatments of wire and sheet were conducted in argon or vacuum. Wire specimens, 0.064 in. diam, were heated for 1 hr at 850 °C to establish a definite

Jan 1, 1957

Thirty years ago a party of American Engineers, with members of their families, belonging to the four national engineering societies, sailed for Europe and visited England and the Paris Exposition of 1889 and received many courtesies, official, professional, and individual. Plans: have been made for a reunion dinner to be held in New York City, about May 26, at which it is hoped that all survivors, ladies as well as men, of that trip may meet again. It is, therefore, urgently requested that anyone who was of that party communicate immediately with the Secretary of the Committee, Jesse M. Smith, Engineers' Club, 32 West 40th St., New York, N. Y. Announcement of the precise date and place, and full details, will he sent to every individual who can he reached.

Jan 5, 1919

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.' Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth's atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.' Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb', with a radius of 1.47 A, is close enough in size to K' (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

By H. O. Hofman

WHEN dry chlorine gas is made to act in the cold upon finely¬divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au2CI4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and aerie chloride, Au2C14 = AuCI + AuCI3; treatment with water converts it into auric chloride and gold, 3 Au2CI4 = 4 AuC13 + Au,. Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCI = AuCI3 + Au,. These decompositions of auro-auric chloride and of aurous chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose,' fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also states that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed checks, and finally stops, further action, if the percentage of silver be increased beyond a certain undetermined amount. Bromine' acts upon finely-divided gold in a manner similar to chlorine; the auro-auric bromide, Au2Br4, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach-

Mar 1, 1905

Jan 1, 1959

By AIME AIME

THE American Engineering Council, which is the working body of The Federated American Engineering Societies, held its first meeting in Washington, Nov. 18 and 19, 1920. The Federated American Engineering Societies was formed in Washington in June and is composed of engineering and technical societies, national, state, local and regional. These Member Societies elect delegates to the American Engineering Council, which is the administrative body of the Federated. The meeting was called to order by Richard L. Humphrey, Chairman of the Joint Conference Com¬mittee, and the program (which is printed below) was carried out without substantial change by E. S. Carman, who was elected temporary chairman. Under the Constitution, the Council appoints an Executive Board, the members of which are chosen according to the proportional membership of the vari¬ous Member Societies in their respective districts. Under this plan, with the present membership, 'the national societies will have 14 members and the local societies 6 members on the Executive Board.

Jan 1, 1920

Jan 1, 1947

Jan 1, 1947

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By W. V. Long, D. H. Reynolds, R. B. Bhappu

Equilibrium distribution coefficients were determined for some monovalent and polyvalent ions for several absorbing and exchanging media as functions of pH and initial ion concentration. Among ions studied were NH4 (I), K(I), Ni(II), Ce(III), Th(IV), and Mo(VI). Absorbents used were: ion exchange resins; a tertiary, and a quaternary amine in an inert solvent; and some activated carbons. The ions studied were in aqueous HCI, HNO3, H2SO4, or HC104 solutions. The classical mass action expression proved of little value in describing the variations observed. The data indicate that the determining factors in absorption and ion exchange may be the ionic species in the aqueous solution, which in turn depend upon pH, dilution, and perhaps other conditions. Three sorption processes have become prominent in recovering values from leach solutions. These are: 1) ion exchange, 2) solvent extraction (liquid ion exchange), and 3) physical adsorption by materials of high specific surface. In the first two of these processes the exchange reaction is considered chemical in nature, and is discussed in terms of the mass action principle. The third is considered a surface phenomenon and is discussed in terms of surface areas and various forms (Gouy, Stern, Grahame, etc.) of the Helmholtz double-layer theory. Generally speaking, we have found in chemical analysis and hydrometallurgical studies that there are close similarities between the three sorption processes, and also differences which are difficult to reconcile with any of the usual theoretical treatments. That others have experienced the same troubles is shown by the fact that usable processes, in chemical analysis as well as in hydrometallurgy, generally are discovered by empirical procedures. EXPERIMENTAL CONSlDERATlONS The gaps between theory and practice have allowed many conflicting statements to appear in the litera- ture. To learn, in particular, the behavior of some metallic ions on a cation exchange resin at a constant pH, equilibration studies were made over a wide range of concentrations.' Results are shown in Fig. 1 for four metals in hydrochloric acid solution on a strongly acidic cation exchange resin, AG 50W-X8 (Bio-Rad). The distribution coefficient, defined as D = amount of metal extracted per g of resin/amount of metal unextracted per ml of solution is seen to vary in a way to support all manner of reports about its behavior with changes in solution concentration. The metals used were chosen from those least likely to form stable chloro-complexes. The changes of slope in the various isotherms may reflect formation of unsuspected chloro-complexes of low stability (ion-pairing for example) whose concen-

Jan 1, 1967

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By C. F., Christopher

The purpose of any steel-making process is to convert the two raw materials iron and scrap into steel. The chemical analysis of the steel is set within certain limits which involve the physical proper- ties desired by the consumer. In addition to tensile properties a large number of other properties are at the present time desired, such as impact resistance, grain size regulation, specific degrees of hardenability, resistance to creep at high temperatures, resistance to expansion on heat treatment, the ability of the product to undergo extreme amounts of cold deformation without failure, and many other properties which are not directly related to the specified chemical analysis. Variations in many of the properties of plain-carbon steels are due to elements and compounds not included in the ordinary "five element"§ composition. Such variations result primarily from variations in oxidation of the metal in the furnace and from the deoxidation method employed. The steel-making problem therefore resolves itself into two distinct sections: (I) the elimination of certain elements from the charge (the iron and scrap entering the furnace) and the addition of materials to meet the chemical specifications for the heat; (2) the manipulation of the slag and metal and the process of deoxidation to give certain desired properties in the steel entirely apart from the chemical analysis specified. Each of 'these two ends must be attained

Jan 1, 1957

Jan 1, 1902

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963