Search Documents

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907

By George Beavers

FLASH roasting of iron concentrate is in the experimental stage at Copperhill. The problem is peculiar in that the iron concentrate is predominantly pyrrhotite; the ratio of that mineral to pyrite being 5 to 1. Results so far indicate that the heat, generated in roasting a material containing 52.0 per cent iron and 38.0 per cent sulfur, requires special handling and for this reason the installation costs per ton of roaster feed may be too great to compete with hearth roasting. Interesting features of flash roasting at Copperhill are: 1. The sulfur dioxide content of the roaster exit gas can be varied between wide limits. Eight per cent sulfur dioxide gas, with 1.30 per cent sulfur in the calcine, has been common practice and gas up to 13.0 per cent sulfur dioxide has been possible. 2. Temperatures of the exit gases are very high. When roasting 60 tons or more of iron concentrate per 24 hr. in a modified Wedge roaster, the temperature in the roaster rises to 2000° F. and the calcine is lowered to 0.20 per cent sulfur. If the entire roaster system could be constructed to withstand such temperatures, ideal roasting conditions would obtain as regards sulfur elimination and tonnage roasted.

Jan 1, 1934

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.' It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt' reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements' are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases' and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By Cornelius F. Kelley

SEVENTY-FIVE years ago, in Wilkes-Barre, Pennsylvania, 22 men of vision banded together to initiate this great organization. Ideals and emotions mingled and united in the declaration of a twofold purpose: first, the more economic production of minerals and metals, and second, the promotion of greater safety and welfare for each man so employed-tacit recognition of the inseparability of humanitarian and utilitarian concepts of world progress. The members and honorary members then, as now, were mining engineers and associates from allied walks of life. Under the able guidance of David Thomas, our first president and outstanding ironmaster of the time, there were elected 46 members and associates, and the foundations of the Institute were laid. Conceived in a turbulent postwar era, the problems then faced had some similarity to those we face in this time of war-bashed uncertainty. With a Civil War behind them and once again dedicated to a spirit of national endeavor, they surveyed the landscape, then surged ahead toward a beckoning industrial horizon. That effort has never been relaxed. Poised upon the threshold of a new century, rancher, banker, engineer and businessman paused to contemplate and evaluate his natural endowments. Surrounded by immeasurable God-given wealth, necessity inspired

Jan 1, 1947

By R. C. Hall

DEVELOPED to grow single crystals of alloys of high hardness and high melting points is a simple but effective apparatus described in this note. Growth from the melt, that is, by the Bridgman technique, hay be applied to metals or alloys which are physically hard as long as no phase transformation occurs on cooling to room temperature. The present apparatus was employed to grow single crystals of the ferromagnetic AI-Fe alloys above 1 wt pct Al and the Si-Fe alloys above 3 wt pct Si. Single Crystal Growth In a simple form, the method for growth of single crystals from the melt requires a molten metal charge in a pointed crucible which is slowly low-ered through a heated zone into a colder zone. Solidification starts at the bottom point and continues up the charge as the crucible is lowered through the heated zone. If a single crystal nucleates at the bottom, one crystal may grow throughout the charge under ideal conditions of slow growth.4,5 The presently developed method of growth was designed so that the chances that more than one crystal would grow were small. The single crystals were growth by the apparatus illustrated in Fig. 1. The charge was in the form

Jan 1, 1958

By Hsun Hu, B. B. Ruth

The rates of migration of high-angle boundaries in zone-refined aluminum crystals rolled 20 to 70 pct in the (110)[i12/ orientation were studied. Following a recovery anneal at an appropriate temperature to stabilize the polygonized structure, boundary migration rates of artificially nucleated grains were measwed isothermally at several temperatures. Results indicate that the rate of boundary migration depends strongly on the amount of deformation and on the cell size of the polygonized matrix, and is related to the driving free energy by a power function. The degree of anisotropy in growth 0.f the re crystallized grains nn&apos;th preferred mientation is independent of deformation; the migration rates of the fast-moving and the slow-moping boundary segments of a gowing grain differ by as much as one order of magnitude. The actir\ation energy fm a grain boundary migration, although nearly the same for both the fast-moving and the slow-moving boundaries for a given deformalion, decreases from 45 to 30 kcal per mole with an increase in deformation from 20 to 70 pct reduction. Re crstallization by the growth of the artificially nucleated grains results in preferred orientation. The Percentuge of&apos; grains favorably oriented for growth increases with increasing deformation. None of these grains corresponds to the ideal Kronberg-Wilson orientation relationship. The observed growth aniso-tropy is discussed in terms of boundary structure. The boundary velocity as a function of the cell inter -facial area, or the driving free energy, is discussed in the light of current theories of boundary migration. It is well established that recrystallization with re-orientation occurs by the migration of high-angle boundaries of strain-free grains. The driving force for this process is provided by the free energy stored in the metal during deformation. A quantitative study of the effect of varying driving force on grain boundary migration in deformed metals has not been possible heretofore, primarily because of: 1) concurrent recovery steadily decreasing the available driving free energy for boundary migration, &apos;-3 and 2) in-homogeneity of strain in the deformed metal.4 Aust and Rutter3 studied grain boundary migration in striated single crystals of zone-refined lead. Although the driving free energy in such crystals remains unaltered during annealing, this method does not provide a range of driving free energies over which measurements of grain boundary migration can be made. In the present investigation, the rates of migration of high-angle boundaries in deformed aluminum zone- refined single crystals were studied at various temperatures, after deformation ranging from 20 to 70 pct reduction by rolling at -78°C in the (ll0)[i12] orientation. The boundary migration rates along different crystallographic directions were determined under steady-state conditions, i.e., in the absence of competing recovery processes or impingement of recrystallized grains growing into the deformed single crystal matrix. Simultaneous recovery was eliminated by suitable anneals prior to the boundary migration measurements. The recrystallized grains, which grew a ni so tropically into the homogeneously polygonized matrix, developed flat boundary segments during early stages of growth. These boundary segments subsequently migrated along a direction approximately normal to the boundary plane into the matrix rystal. Increasing deformation over the range employed was estimated to increase the driving free energy for boundary migration by about five times. The kinetics of the boundary migration process, examined under these conditions, indicate that the boundary velocity is greatly affected by a small change of the driving free energy in the matrix crystals. These results were examined in the light of the current theories of grain boundary migration. EXPERIMENTAL PROCEDURES Single crystal strips (9 by 1 by 0.125 in.) of zone-refined aluminum, were seed-grown by the Bridgman method in a high-purity graphite mold (<lo ppm ash) at 1 in. per hr. Precautions were taken to minimize contamination of the metal during crystal preparation and subsequent handling. Spectrographic analysis of the metallic impurities in the grown crystals is Qven in Table I. The crystals were rolled in the (110)[112] orientation at -78°C to various reductions in thickness, ranging from 20 to 70 pct, in 10 pct increments. The desired reduction was achieved by many rolling passes, each being no more than 0.002 in. To minimize surface friction, the crystal was rolled between two thin layers of teflon. For those crystals rolled more than 40 pct, it was necessary to remove the disturbed surface layers by electropolishing at -5" to -10°C at an intermediate stage of rolling. The edges of deformed crystals were removed by a jeweler&apos;s saw while submerged in alcohol at -78° C to obtain samples of about ? by i in. The distorted metal at the cut edges and the surface layers were then removed by electropolishing, with removal of a minimum of 0.004 in. from each surface. The thickness of the crystals prior to rolling was chosen so that the final thickness was 0.025 in. for all samples. These deformed single crystals were each prean-nealed for 1 hr at an appropriate temperature in the range of 130" to 280°C, depending upon the amount of deformation. The purpose of this preannealing was to

Jan 1, 1970

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today&apos;s quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By Kenneth E. Mathews, Ross D. Hammett, S. Byron Stewart

Theoretical models have been important throughout the history of engineering as a means of understanding past experiences and predicting future performance. Most modelling involves assumptions and a degree of idealization, and it is shown that it is important that the effects of these be recognized when making use of models. One of the principal concerns in underground mining is the effect of the excavations on the states of stress in the rock adjacent to these excavations. As mining proceeds to depth, stress concentrations may be sufficiently high to cause inelastic behaviour of the rock and yielding along joint surfaces. At this stage, attention must be given to the sequencing of the mining process to ensure that the ground control techniques applied are optimized. Increasing use is being made of computer modelling techniques to assist with design. Three case studies are presented to illustrate the application of computer models in mine planning and ground control. In all cases, the data available for design was limited, but the mines were fully developed and openings could be inspected. The mining methods studied are cut and fill stoping, room and pillar stoping, and longhole stoping.

Jan 1, 1983

By D. O. Ehrenburg

DURING the earlier period of electrical prospecting, the search for orebodies was by far the most important application of this method of geophysical prospecting. In the past few years, however, increasing attention has been paid to the possibilities of this method in the investigation of subsurface structures. Not only have fault zones been located, but attempts have been made to determine the depth to certain strata and thus contouring on some bed which proves to be a good "electrical marker." Many workers have published the results of field tests showing how their particular interpretations have agreed with the actual field conditions, but very few have stated their method of interpretation. Weaver, Hummel and Stefanesco and Schlumberger1 have given a more theoretical discussion of the resistivity methods. Hummel and Stefanesco and Schlumberger have published mathematical solutions for the flow of electricity in a medium involving four layers. In this paper the authors present a solution for the flow of electricity in a medium of any number of horizontal strata. By means of this solution, curves showing the relationship between the apparent resistivity and the electrode spacing can be computed for ideal cases.

Jan 1, 1931

R. L. Bullock (St. Joseph Lead Co., Bonne Terre, Mo.)— The progressive approach of The International Salt Co. as described by Mr. Ryon is certainly commendable as is his paper. St. Joseph Lead Co. has been shooting AN/FO in 13/8 to 1 1/4-in. holes for several months now (as of October 1960) on a trial basis. The results thus far obtained are excellent, but conclusive evidence at this date is premature. One point that he gave should interest even the most ardent skeptic. That is, they are getting a detonation of the 1 1/4-in. ANDO charges in 2 1/4-in. holes. In light of its low sensitivity and critical diameter, this would appear to be one of the worse conditions that one could expect in which to get proper detonation of AN/FO. It has been shown* that partial confinement sometimes decreases sensitivity of a column of explosive because the air space above the explosive becomes highly compressed and in turn compresses the explosive prior to passage of the detonation front. Apparently, this does not happen in their shooting and the poor explosive coupling caused by the 2 1/4-in. holes yields a minimum of overbreak and is an ideal condition for their back.

Jan 1, 1961

By V. I. Purcell, R. E. Snow, S. C. Sun

FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo- wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being pre- dominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon.

Jan 1, 1957

THE Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered under Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library" The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpetually as a meeting place and headquarters for the Founder Societies Thus the Carnegie gift realized the ideal of bringing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint interests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and

Jan 1, 1952

By Edward Hanrahan

September 1981 I&apos;m here today to report on a revolution -- a revolution in the way the Federal Government looks at energy. I&apos;m not talking about a simple change in the relative emphasis on sources -- such as more recognition for coal and nuclear power, with less rhetoric about "soft- technology." Nor am I describing a mere change in focus -- from the demand side to the supply side. And I am not referring exclusively to our obvious goal of budget cuts. No, I&apos;m here to discuss a fundamental change in Federal direction -- one that started as soon as President Reagan was inaugurated, and one that is articulated in the National Energy Policy Plan he sent to Congress in July. That brief policy document was backed up by three volumes of supporting data; but I think I can catch it&apos;s flavor for you in just three phrases: * First, various energy forms complete with each other and complement one another. * Second, fair competition among them (which includes honest pricing) will give us the best "energy mix." • And, finally there may be ligitimate arguments about where Federal responsibility in regard to energy spills over into Federal interference; but it&apos;s about time we drew the distinction -- and eliminated the latter. This Administration&apos;s national energy policy is quite different from any we have had in recent years. It is tuned to human nature and changing times. We are seeking the best practical solutions in the energy -a lot better than the ones we have been offered before, but still something less than perfection. One way we do that is by counting on a fully informed public to guide it&apos;s own destiny. And, instead of treating energy as an isolated entity, we recognize it as part of the overall economy. The President&apos;s Program for Economic Recovery is as much a factor in energy policy as the specific actions of the Department of Energy. One striking difference from the past energy policy 1s that this policy plan does not say: "In 1985 we will -produce so many hundreds of millions of tons of coal: . . . or . . . "By the end of this century the Nation will be deriving X percent of it&apos;s electricity from wind generators." Unfortunately, targets like these are what many people have come to expect from the Federal Government -- and what they think of as energy policy, whether the figures hold up in the long run or not. But . . . think about it! Nether the Department of Energy nor any other part of the Federal Government produces coal, or mines uranium, or manufactures solar collectors. There are only a few sections of the country where the Federal Government generates and sells electricity. So it does not take any great insight to recognize that the amount of energy we will produce or consume as a Nation In the future depends on many factors beyond direct government action. And those future totals cannot be predicted precisely, anyway -- by the Government or by anybody else. According to our way of thinking, the choices should be up to the people. When the free market works within a healthy economy, individuals express their preferences in the marketplace -- adjusting the balance of all energy factors continually in a way that no computer could be programmed to reflect perfectly. So, instead of having the Government issue a rigid set of numerical goals, our main concern simply is that there be enough energy. We want the Nation itself to decide how much that should be, what form it should take, and how that energy should reach consumers. The marketplace decides. Considering the recent past, this is indeed a revolutionary idea. It has some pitfalls, and we won&apos;t reach this ideal of free choice overnight. But that is where we are headed. And I&apos;ll offer some evidence in a few minutes that the policy has already started working. First, let me give you some of it&apos;s highlights: 1) Nobody who appreciates the philosophical underpinnings of this Administration will be surprised that the energy policy shows faith In domestic energy production and the supply side of the economy; but it also recognizes the important role of energy conservation -- the wise and efficient use of energy resources.

Jan 1, 1982

By F. R. Morral, K. T. Aust

The preferred orientation and earing characteristics of ZS aluminum were studied. An empirical correlation was obtained relating earing behavior and variation of mechanical properties for face-centered cubic metals. Strain-ratio mecsurements for ZS were found to be in good agreement with Hill&apos;s theory of plastic anisotropy. DIRECTIONALITY in sheet metals may be revealed by earing in a cupping test, or by the variation of mechanical properties of tensile specimens taken at different angles to the rolling direction. However, no simple correlation appears to exist between earing and variation in mechanical properties in metals and alloys studied.1-5 Aluminum of commercial purity (known as 2S, with a specified minimum of 99.0 pct Al) cast by the direct casting process was chosen in the present investigation since ears at 45° or 0°, 90° can readily be obtained. Preferred orientation is often the principal cause of uneven metal flow, such as earing, and variation in mechanical properties. Consequently, the preferred orientation characteristics of 2s aluminum were initially studied using both X-ray diffraction and micrographic techniques. The variation of mechanical properties with angle to the rolling direction was next determined in an effort to clarify the apparent lack of correlation of earing behavior with mechanical properties for face-centered cubic metals. Strain-ratio*5,8 measurements were finally conducted to determine first, if the maximum values of the strain ratio occurred at the earing positions, and second, if Hill&apos;s theory of plastic anisotropy7 is applicable to other face-centered cubic metals such as aluminum. Detailed treatments, working, and heat treating are not given in this paper since this study is not concerned with the methods to produce earing, but to correlate earing with other properties and characteristics of the material. The percentage of earing was measured using the formula specified by the x—Y Aluminum Association, -------- X 100 = pct earing, where x is the height of the ear and y is the height of the valley from the bottom of the cup. Preferred Orientation Characteristics of 2S X-ray Studies: Beck and coworkers8 have determined that the rolling texture of 2s after 95 pct cold reduction may be approximately described by four equivalent ideal orientations near (123) [121]. Also, the recrystallization or annealing texture of 2s aluminum consists of four components of the (123) [l21] type, retained from the rolling texture, and of a (100) [001] or cube texture component." Fig. 1 illustrates the typical appearance of deep drawn earing cups with the corresponding X-ray diffraction patterns. The X-ray patterns were taken with copper radiation using the structure-integrating method&apos;" in which the specimen is scanned during the X-ray exposure. The rolling direction was vertical and the rolling plane was perpendicular to the horizontal X-ray beam. It was found that an increase in the retained rolling texture component resulted in a greater 45" ear height, while an increase in the recrystallization texture component (i.e., cube texture) caused greater 0°, 90° earing. X-ray diffraction studies of 2s cold rolled to final thickness followed by a final anneal have shown that the rolling texture, and also the retained component of the rolling texture after annealing, are increased with greater cold-rolling reduction. The preferred orientation characteristics of 2s sheets given an intermediate anneal between cold rolling followed by a final anneal were found to depend on the position of the intermediate anneal during cold rolling. For instance, three identical samples of 2s homogenized ingot, each 1 in. thick, were given the following cold-rolling and annealing treatments: 1—50 pct reduction, intermediate anneal, 96 pct reduction to 0.020 in. and a final anneal; 2—75 pct reduction, intermediate anneal, 92 pct reduction to 0.020 in. and a final anneal; and 3—90 pct reduction, intermediate anneal, 80 pct reduction to 0.020 in. and a final anneal. The intermediate and final annealing treatments consisted of a 70°F per hr heating rate, held 6 hr at 800°F and air cooled. Typical X-ray patterns after each of these treatments are shown in Fig. 2. It was evident that after treatment 1, the retained rolling texture component predominated; after treatment 2, the retained roll-

Jan 1, 1954

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy&apos; presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. &apos;References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,&apos; and Carter et a1.&apos; treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy&apos;s law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By S. Vela, R. M. McKinley, L. A. Carlton

Johnson et al. have described a new well-testing technique that measures formation flow properties between wells.&apos; The technique, called pulse-testing, requires a sequence of rate changes in the flow at one well and measzcrement of the re.rulting pressure changes at an adjacent well with a very sensitive differential pressure gauge. This paper describes an extensive application of the technique in a producing oil field. Pulse-tests on 28 of 45 possible well pairs in the field provided a picture of the areal distribution of reservoir hydraulic diffusivity, trans-missibility and storage. The primary objective in presenting these data is to demonstrate the potential of the methcid for reservoir description. A second objective is to show in three ways the qualitative and quantitative accuracy of reservoir parameters determined from pulse-tests: (I) pulse-test data show a nonuniformity in the field, closely correlating with the oil-water distribution as given by production data: (2) pulse-test values for permeability are comparable with core va1ue.s; and (3) perhaps most important, the field responds to a conventional interference test in the manner in which pulse-test data predict it should. The pulse-testing technique by Johnson et al.&apos; is an ideal source of data for purposes of reservoir description, for it provides a measurement of formation storage S = +ch, hydraulic diffusivity 91 = k/+cp and transmissibility T — This paper describes an application of this method in a producing oil field. Results were analyzed to give numerical values for the parameters 7, T and S. These values were compared with oil-water production data (for the effect of fluid saturation), with core data and with data from an interference test. The reservoir in which the pulse-test survey was run is the result of a structural trap formed by a fault along the east side of a north-south trending anticline. A down-structure aquifer providcs a natural flank water drive for the pool. The producing formation is a dolomitic lime- stone having mainly vugular permeability; the formation oil has a gravity of 29" API with negligible dissolved gas. The field contains 19 wells, all on pump, arranged on 40-acre spacing along the top of the anticline. Fig. 1 shows the location of all these wells except two at the south end of the field. The dashed line on the right-hand side of the figure represents the approximate location of the fault with respect to well positions. Pulse-Test Survey and Analysis of Data A pulse-test requires a pulsing well and a responding well. In the field, changes were made in the rate of flow at the pulsing well by stopping and starting the pump periodically and measuring the corresponding pressure

Jan 1, 1969

By C. W. Waidner

THE standard scale of temperature that it is attempted to realize in practice is the centigrade thermodynamic scale, as defined by Kelvin about the middle of the last century. This scale would be exactly realized with a perfect1 gas in an ideal gas thermometer, and is closely realized with the more permanent gases. From the departure of certain properties of these gases from those of a perfect gas, it is possible to deduce the amount of the departure of the temperature scales, defined by their use, from the thermodynamic scale. In nearly all the precise experimental work done during the latter part of the last century, it was necessary for the experimenter to establish his own gas-thermometer scale, and the labor involved in this was often greater than that involved in the prime object of the experimental work undertaken. The experimental difficulties involved in gas thermometry led to the establishment of temperature scales differing from one another by amounts considerably greater than could be accounted for by the differences in the properties of the gases used. Results were, therefore, expressed in terms of somewhat different temperature scales, snaking correlation of such results difficult and uncertain.

Jan 9, 1919

By Harry E. LeGrand

Most mine operations are hampered to varying degrees by excessive inflow of water into mines or scarcity of water for processing the materials. These internal problems are compounded in many cases by such external hydrological problems as lowering of ground-water levels in areas outside the mine properties, subsidence of ground surface, adverse geochemical changes, and pollution. The development of a mine below the water table disturbs the natural ground-water system, causing a convergence in the flow of water from a surrounding area. The mine becomes the apex of a depressed cone in the water table. The fact that mines are commonly located in complex and somewhat anomalous geologic environments prevents an idealized treatment of the mine as a well that would be similar to a water well in a homogeneous aquifer having isotropic conditions. Yet, adherence to some principles of ground-water behavior is helpful when combined with an understanding of the local geology. A program calling for an appraisal of all pertinent hydrological conditions prior to mining and during various stages of development should supply adequate information for mine officials to anticipate difficulties and to allow for corrective measures. Before and during mining operations there should be a mine hydrology framework and plan, in which there is continual upgrading of such considerations as anticipated actions, consequences of actions, remedial plans, and contingencies.

Jan 1, 1973

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953