Search Documents

By George T. Hansen

WHY try to find oil in Utah? Why try to find oil anywhere? Isn't there too much oil already? Answers to these questions involve general oil conditions but are pertinent to my subject. In the first place oil produced in Utah up to the total amount of local consumption would not be subject to nor concerned with the national oil situation. An oil field in this State capable of producing up to 15,000 bbl. per day would have a large value and prompt realization. In the sec¬ond place, there is not too much oil nationally although the markets have been upset temporarily from time to time. Petroleum is so necessary and is in such general demand that an oil field anywhere, anytime, is a valuable and live asset. The oil business in general shows the best condition of any major industry. It has never been hit as hard as most industries and 1932 was a large improvement over its low spot of 1931. It can be and probably will be the one to lead the country back into business stability. Consumption of its products has been reduced less than that of any other important commodity. There are good and valid reasons why it should have been making a normal profit continuously. It has the oil and the processes and the facilities and the policies and the consumption of its products. There is only one reason why it has not been profitable recently and that is the lack of intelligence of from five to ten per cent of the producers. An op¬erator lacks intelligence when he cannot see that it is better for him to sell one barrel of oil at $1 than two or three barrels at 25 or 35c. per bbl.

Jan 1, 1933

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By Noel Cunningham

MANY excellent descriptions of the mills of the, Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 2 ½ years' mill operation in the district-i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.-There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15? of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured .and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a ½ -in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling.' In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more-or less blocky at times, and with ref¬erence to Class B this is indicative or low gold content.

Jan 3, 1915

By John F. Wiggert

DURING the early years of Homestake operations, shaft signaling from the cage tenders to the hoisting engineers was done by mechanical means. Small steel cables or jointed steel rods were suspended in the shaft compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' stations by means of bell cranks and steel wires. The system was simple and economical and served the purpose well until the mine reached a depth of 1000 ft., then the system became slow and cumbersome and required a considerable amount of muscular effort to operate it with much speed, because of the inertia of the heavy moving parts. The mechanical signaling was superseded by a simple electrical system consisting of a single pair of wires in steel conduit for each shaft compartment. In the shaft at each station a pull switch was connected to the wires. The switches were operated by means of bell cords, which extended from station to station. This electrical system was a great improvement over the mechanical one, but it had one serious drawback, which also applied to the older system; namely, the engineer did not know where a signal originated. Later on this signaling was improved to overcome this drawback, and to give the engineer a positive indication of a signal's origin. In this system a separate return wire from each pull switch is carried to an annunciator at the engineer's station, where it indicates the signal's origin. While the annunciator system used by Homestake is very safe and reliable, it has the inherent drawback of all wire-connected systems in that it is impossible to send a signal from a moving cage. A number of years ago Homestake became interested in the possibility of using some sort of radio transmission for shaft signaling. The company did much experimental work with purely radio signal transmission, but no practical way was discovered to use radio transmission in a mine shaft for signaling to or from a cage. Therefore, all efforts were directed to devising a practical way of using the hoisting rope as part of the circuit. It was realized that the return circuit from the rope would need to be through electrostatic coupling between the cage and the earth or ground sides of the shaft, because the guides would not always be wet enough to make possible good electrical contact between the cage and earth, therefore relatively high-frequency alternating current was chosen as the medium of transmission. Soon a practical system was developed for transmitting an electric current from a moving cage over an electric circuit of which the hoisting rope was a part. A high-frequency electric current is used as a carrier to transmit the signals or mes-

Jan 1, 1941

At the annual meeting of Southern California Section, held on May 28, the following officers were elected: Chairman, W. F. Staunton, vice-chairman, L. C. Mott, secretary-treasurer, A. B. Carpenter; executive committee, J. W. Neill, C. Colcock Jones, Mead Goodloe. ALVIN B. CARPENTER, Secretary-Treasurer.

Jan 8, 1919

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

Established as a Division March 24, 1922 R B Gilmore, '57, Chairman G L Yates, '56, Vice-Chairman Phil J Lehnhard, '56, Vice-Chairman John R McMillan, Past Chairman T A Pollard, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Building Dallas 1, Texas

Jan 1, 1955

[OFFICERS AND COMMITTEES J. W. Woomer, President A. B. Cummins, President-elect S. D. Michaelson, Past President C. E. Lawall, Eastern Regional Vice-President D. W. Scott, Central Regional Vice-President J. D. Forrester, Western Regional Vice-President R. B. Ladoo, Treasurer John Cameron-Fox, Secretary]

Jan 1, 1961

By Axel Sahlin

Jan 1, 1898

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

By Fred D. Fox

INTRODUCTION Approximately two years have elapsed since the first summary of the Grizzly Gulch Tailings Disposal Project was presented (1). Since that time, various physical modifications and additions to the existing treatment system have transpired. Further, Homestake and the entire mining industry have been impacted severely by additional modifications and additions concerning regulatory reform aimed at total disciplinary permitting and hazardous waste management. The following paper summarizes the past accomplishments relating to the Grizzly Gulch Tailings Disposal Project, correlating these accomplishments with future plans that are being developed to comply with regulations and to continue Homestake's commitment to environmental protection. The famous Homestake Gold Mine, located in Lead, South Dakota, has been operating in the Black Hills region for over a century, approximately 12 years before the south half of Dakota Territory was admitted to the Union as the State of South Dakota (2). During the 104 years of operational development, Homestake's Gold Mine, as well as the entire mining industry, have been influenced by numerous governmental regulations dating back to the Refuse Act of 1899 which regulated the deposit of debris from mines and stamp works. The enactment of the National Environmental Policy Act of 1969 may be thought of as the beginning of a long line of unplanned steps to deal with the many concerns of matters pertaining to the environment. Environmental awareness continued into the 1970’s, in which the Clean Air Act, Federal Water Pollution Control Act, Safe Drinking Water Act, Toxic Substances Control Act, and the Resource Conservation and Recovery Act (RCRA), to name a few, surfaced.

Jan 1, 1983

University of Alabama University, Alabama Mining and Metallurgical Society JOSEPH CHARLES MEAD, President WAYNE G. BRIGGS, Secretary J. R. CUDWORTH, Faculty Sponsor RICHARD L. BOWRON, Counselor University of Arizona Tucson, Arizona Miners' Society W. JAMES THOMAS, President LAMONT WEST, Secretary J. B. CUNNINGHAM, Faculty Sponsor B. R. HATCHER, Counselor

Jan 1, 1938

ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E. Auburn, Brown, R. L. Bessemer, Abbott, C. E., Ferguson, V. Birmingham, Aldrich, T. H., Aldrich, T. H., Jr., Allen, A. W., Bowron, J., Burbidge, T. A., Crawford, G. G., Crockard, F. H., Davis, F. H, Dimmick, F: D., Ellis, E. E., Geismer, H. S., Hiller, E., Johnson, G. R, Ludwig, C. P., McCormack, G. B., McCrery, Peters, R, Jr., Phillips, W. B., Pill, J. R., RamSay, E. Coal City, Pattberg, 0. F. E-msley, Wil¬liams, E. P. Helena, Squire, J. Holt, Shook, J. W. Huntsmlle, Moss. Ironton, Hudson, J., B. Lehigh, Toulmin. Bock Bun, Garvin, J. M. Woodward, Wood¬ward, A. H.

Jan 1, 1910

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve -Engineers. AMBLER, HARRY A., Second Training Camp, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22c1 Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers' Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 10, 1917

AARONS, J. BOYD; Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. AMBLER, HARRY A., Second Training Camp,, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy' Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers' Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 11, 1917

By John V. Beall

AMONG electrical manufacturers, interest in the outlook for copper supplies has not diminished despite signs of a healthier market following price decontrol. Reason: Electrical utility industry output is expected to grow at an average annual rate of 6 pct for the next 15 years. A more graphic description of the growth ahead is given in the Eighth Quarterly Report of the Director of Defense Mobilization as follows: "Power generating capability, which amounted to 63 million kw at the time of Korea, now stands at more than 81 million. The established goal for installed capability at the end of 1955 is 116 million kw. Orders already on the books of power equipment manufacturers, if fulfilled on schedule, will bring installed capability to over 123 million kw by the end of 1956-and more orders for equipment are yet to come." These statistics portend an impressive requirement for copper, not only for power plants and distribution lines themselves but for the multitude of industry and domestic end-uses.

Jan 4, 1953

By J. E. Tobey

NATIONAL DEFENSE should not create a dilemma in coal utilization such as obtained during the World War. Even under the heavy pressure of a total preparedness program there should be a smooth flow of the right coals from mines to plants. The more than 100,000 industrial plants of the nation must he served with coal of such characteristics and qualities for their individual requirements that no loss of production due to coal failure shall occur. This problem challenges the ingenuity and cooperativeness of producers. transportation executives, consumers and engineers.

Jan 1, 1941

By Henry J. Sandri

The use of economic models for forecasting purposes is an inexact yet necessary tool for mineral decision making. One method not commonly used is cyclical analysis because of its "non-scientific approach". However, under certain circumstances a modified cyclical approach can provide useful insight to mining companies. The current paper discusses mineral modeling, the type of economic models and the use of cyclical forecasting for mining firms (not speculators) involved in precious metals.

Jan 1, 1984