Search Documents

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick's equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By A. Tanaka, K. G. Carroll

The existence of local room-temperature plastic flow in germanium, which has been a subject of controversy for nearly two decades, has recently received renewed attention, albeit no more agreement than hitherto. Phenomenologically one major facet of the problem has been reduced to the question whether or not indentation can be effected in germanium without the introduction of cracks. That plastic flow can be induced at room temperature by fracture appears to have been rather convincingly demonstrated recently by Suzuki and Kamada and by Noble and Henisch.1 The literature contains both direct and incidental references to Vickers and Knoop indentations showing no cracks, within resolution of optical microscopy. Recently, however, following a controversy on the subject,2,3 johnson4 made a study of indentations produced by spherical indenters and concluded that these are accompanied by cracking. This study in-

Jan 1, 1969

By Lawrence Adler

For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.' This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.'

Jan 5, 1960

By P. Ramakrishnan, Ramjilal

Fine powders of lead zirconate titanate have been prepared by three different methods such as ball milling, conventional coprecipitation and spray drying. Different powders have also been prepared by changing the process variables in each method. These powders were analysed for particle size chemical composition and reactivity. DTA, TGA and x-ray analysis have been carried out to study the lead zirconate titanate formation with reference to calcination temperatures. The calcined powders were then consolidated by compaction and sintering. An attempt has bean made to explain the consolidation behaviour of these powders on the basis of powder characteristics.

Jan 1, 1980

By P. Somasundaran, G. E. Agar

The role of calcium, phosphate, and fluoride species in determining the zeta potential of apatite in aqueous solutions was investigated in this study. The zeta potential of apatite was determined by streaming potential measurements over a wide range of concentrations of potassium nitrate, calcium nitrate, potassium dihydrogen phosphate, and potassium fluoride solutions at various pH values. While the addition of phosphate made the apatite surface more negative at all pH values, calcium caused a significant increase of the zeta potential only when the zeta potential was negative. Fluoride addition had only a minor effect on the zeta potential, but both negative and positive values were increased.

Jan 1, 1973

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

By R. W. Raymond

The death of Louis Janin, which took place Mar. 6, 1914, at Santa Barbara, terminated the earthly career of almost the last survivor, and one of the most illustrious members, of that group of American mining engineers and metallurgists who, in the last quarter of the nineteenth century, directed the development of the mineral resources of the Pacific slope. Louis Janin was born in 1836 at New Orleans. His grandfather, an officer in the French army, had emigrated to this country, with his family, at or before the outbreak of the French revolution. His father became an

Jan 1, 1915

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes. The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper1 described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely.

Jan 12, 1954

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932

By T. M. Geffen, R. E. Gladfelter

Lipson1 has recently presented a technical note wherein theoretical considerations were used to demonstrate. that the adsorption us saturation relation for a linear absorption method is not necessarily a single valued function of saturation.1 It was concluded that the absorption us saturation relationship is subject to the same hysteretic effect as is the flow behavior between the drainage and imbibition systems. It is the purpose of this note to show, by experimental results, that for the manner in which fluids are distributed in porous materials during fluid flow, the relative X-ray absorption us saturation relationship is single-valued regardless of the saturation history. The design of the apparatus used to measure relative X-ray absorption of cores undergoing fluid flow tests is similar to that described by Morgan, McDowell and Doty. A few modifications have been incorporated in the design to increase sensitivity and simplicity of measurement. The sensitivity is such that for usual types of cores a recording pen movement of approximately 12 linear in. is occasioned between the recording of the core dry and when it is completely full of an absorbing liquid, a solution of approximately five per cent by volume of iodo-benzene in a close-cut hydrocarbon fraction, or a solution of 50,000 ppm sodium iodide in water. Two types of experiments were conducted, one in which the liquid was inside the core, and the other with the liquid outside the core. Tests with the liquid inside the core were run to cover the saturation range encountered in both the drainage (gas drive) and imbibition (liquid flood) flow systems. It is pointed out that the same core was used, but the tests were conducted at different times with the recording mechanism balanced at a different position. Therefore, the absolute values of relative X-ray intensity at any saturation are not the same in each test. In the second type of test the same core was used, but this time its pore space cmtained only gas, and various thicknesses of oil contained in plastic cells were placed in front of the dry core. As before. the relative X-ray ah- sorption was measured and compared to the quantity of oil in front of the core. The arrangement of the fluids with respect to the path of X-rays in these two types of tests represent fluid distributions of a wider difference than can be expected between that established in a core just due to imbibition and drainage saturation flow histories. Thus any deviation from a straight line relationship of the log of the relative X-ray intensity us saturation calibration should be readily apparent. Results of the laboratory tests are given in Fig. 1. A schematic diagram showing the position of the fluids with respect to the path of the X-ray beam is given for the two cases investigated. In the case where the oil existed outside the core (Case B), the log of the X-ray intensity (log, I/I,) is related directly to the cell thickness (amount of oil in X-ray beam path). This correlation is in full agreement with X-ray theory. In the case where the oil or water existed inside the core (Case A) which covers both drainage and imbibition types of flow processes, again the relationship between absorption and saturation (amount of oil in X-ray beam path

Jan 1, 1952

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

P. W. SHIMER, Easton, Pa. (written discussion*).-When lump calcium cyanamid is immersed in the melt of mixed chlorides of the alkalies and alkaline earths in the manner described in the paper, the amount of sodium cyanide formed in the melt, as shown by numerous analyses, is but a small fraction of that formed by the reaction referred to by Mr. Johnson. The case-hardening effects in my process are, however, at least as good as when the common cyanide baths are used. Moreover, when compared with the cyanide baths, the gases evolved in the new process are harmless, consisting of nitrogen, carbon monoxide (which burns to carbon dioxide on the surface of the melt), and occasionally a little carbon dioxide. These gases are not irritating or poisonous, whereas the vapors arising from cyanide baths are both irritating and poisonous. The complex chemical reactions that take place in and on the surface of the melt are being investigated by the writer, who hopes, in due time, to communicate the results of his work.

Jan 7, 1919

This listing of members is arranged to show company affiliation The primary breakdown is by state or country, then by company name and political subdivision At the end of each major group is a general list showing members affiliated with schools or colleges and those who did not indicate any company affiliation The listing, for countries outside United States, is broken down generally by continents and alphabetically within the continent by countries The various countries are indexed on the preced¬ing page *-The asterisk indicates members available for consulting work Anyone desiring to be listed with AIME as available for consulting work can do so by sending a written request to the office of the Secretary.

Jan 1, 1952

By Walter B. Devereux

Metallic copper is a product of native metallurgy in various parts of Mexico, and by somewhat varied processes. While recently examining copper mines in the State of Jalisko, I had an opportunity of witnessing Mexican copper smelting by a process which I have not seen described, and which is interesting from the fact, that a fine quality of copper is produced from sulphurous ores in three metallurgical operations, and apparently without excessive loss. The process was carried on in buildings which were part of a plant erected by an American more than twenty-five years ago for the purpose of smelting and working copper. After a few years this man met with accidental death, and the works have been but little used since. Located in the centre of a high range of mountains, far from any town or seaport, and inaccessible except over difficult mule trails, these substantial buildings, filled with furnaces and heavy machinery,

Jan 1, 1883

By Thomas M. Drown

The process for determining phosphorus in iron now in most general use in the laboratories of iron and steel works, is, I think, the one proposed bv Mr. Emmerton." In this process the solution of the iron for precipitation by ammonium molybdate is effected by treating the iron with nitric acid, evaporating to hard dryness in a dish, taking up with hydrochloric acid and driving off the greater portion of the hydrochloric by nitric acid. This procedure accomplishes, first, the destruction of all the carbonaceous matters; and, second; it renders all the silica insoluble. Experience has proved the former—the complete oxidation of the carbon—to be absolutely essential; but the explanation usually given, namely, that unless the carbon compounds are destroyed they will have a solvent action on the yellow precipitate, I am inclined to

Jan 1, 1890

By Warren H. Westphal

For mining and exploration, and indeed the entire mineral industry, the first century of AIME has ended with far more problems than it began. Paradoxically, most of these problems have arisen not because, the industry has been unsuccessful, but rather because it has succeeded too well. Whatever the public demand for minerals over the past 100 years, it has somehow been met-and met at a price well within the public's ability to pay for the products. But as AIME moves into its second century, the past successes of mining and exploration are beginning to levy a tax on the future. Prospectors have already found most of the rich and ready ores, and miners have dug them out. New mineral assets grow progressively harder to come by, and as they do, the need for them grows inversely more pressing. How and where and at what cost can adequate supplies be found? How and at what cost can they be mined from heretofore inaccessible recesses deep underground and under the seas-or from vast surface tonnages containing only minor values? And once they are found or won, how can these assets be husbanded for generations to come? How also can they be extracted without injury to the land, air and water on which we and our successors must depend? And what constructive use can be made of the incidental materials now treated merely as wastes-sometimes at great expense?

Jan 1, 1971

Briefly, an open stope is one in which the ore is taken out and no filling is put in; the only support for the walls may be posts or pillars of ore. Such a method is limited to orebodies with strong walls and ore strong enough to stand unsupported over the back of the stope. Details vary and depend on the dip of the vein, mode of breaking ground, method of handling broken ore, and so forth. The examples given are the Beat-son, Birmingham district, Mineville district, and Cornucopia.

Jan 1, 1925

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929