Search Documents

By Milton E. Wadsworth, R. Ted Wimber

Cobalt sulfate solutions containing ammonium acetate and chloroplatinic acid were reduced by hydrogen in a pyrex-glass lined autoclave in the temperature range of 170o to 232°C and hydrogen partial pressure range of 115 to 830 psia. The reduction rate was directly proportional to the hydrogen partial pressure and surface area of the pyrex glass and was independent of the quantity of chloroplatinic acid added initially. Experiments involving the variation of the relative concentration of ammonium acetate indicated that the reducible cobalt complex was probably the diacetate complex of cobalt, Co(AC)4H20, or a new mononcetate complex Co Ac, which was in solubility equilibrium with a pink precipitate of CO(AC)-4HzO. THE reaction in which a metal is dissolved by an acid to produce gaseous hydrogen and a salt solution was discovered early in the history of chemistry. In 1859 Beketoff found experimentally that this reaction could be reversed; i.e., a salt solution could be reduced by gaseous hydrogen to produce a metal and an acid. A review of work done on this phenomenon since that time may be found elsewhere., The hydrogen reduction of a cobalt salt solution is facilitated by complexing the cobalt ion. An ammonia complex of cobalt has been reduced commercially in the recovery of cobalt metal. A new reducible complex of cobalt was discovered5 when it was found that a co-baltous sulfate solution containing ammonium acetate could be reduced by hydrogen at temperatures in the region of 200°C. When a cobalt sulfate-ammonium acetate solution was heated to a temperature below its normal boiling point, a violet color became apparent, indicating complex formation. The nature of this complex was investigated5 by the addition of NH4Ac to a CoSO4 solution maintained at 85o. During the first additions of NH, Ac, the pH of the solution remained fairly constant at about 5.85. However, as the ratio of NH,Ac to CoSO, approached two, the pH rose and then leveled off at about 6.05. The absorption spectra of a Co(Ac), solution and a CoSO,, NH Ac solution were obtained at 85°C and were compared and found to be the same. These findings suggested that the diacetate complex of cobalt, Co(Ac),.4H20, was formed at 85°C. When a cobalt sulfate-ammonium acetate solution was heated to a temperature above about 165o, a finely divided pink precipitate appeared. The X-ray diffraction pattern of this precipitate indicated that it was Co(Ac), - 4H,O. In addition, it was discovered that when chloroplatinic acid, H,PtCl;, was added initially to the cobalt sulfate-ammonium acetate solution, a faster reduction was obtained. The roles of the solution complex, pink precipitate and chloroplatinic acid in the reduction process were then investigated. APPARATUS The experimental work was carried out in a two-liter stainless-steel autoclave. Adetailed description of the autoclave and the auxiliary equipment used in maintaining constant temperature and pressure may be found elsewhere.= Because the stainless steel was corroded, and also because it acted as a hydrogena-tion catalyst, an all-glass liner was fabricated such that the solution came only into contact with flame-polished pyrex glass. EXPERIMENTAL PROCEDURE The solutions used in the experimental work were prepared by dissolving reagent grade chemicals in distilled water. Although variation of the brand of ammonium acetate appeared to have no effect on the experimental results, CoSO, 7H O from the J. T. Baker Chemical Co. of Phillipsburg, N. J.,was found to give faster reductions than that prepared by Allied Chemical and Dye Corp., N. Y. The former was used throughout the course of the experimental work and was weighed up at the outset of each experiment. The ammonium acetate was dissolved to form a 6M stock solution, which was stored under refrigeration. A 10 pct solution of chloroplatinic acid (J. T. Baker Chemical Co.) was diluted to a 1.15 x 1Q2 M stock solution, which was standardized by precipitation of K,PtCl, as outlined by Scott. The appropriate volume of the chloroplatinic acid, H,PtCl,, solution was pipetted into the clean, dry glass liner. The cobalt sulfate-ammonium acetate solution, which had previously been saturated with

Jan 1, 1962

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By Fulton B. Flick

The micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents are available for the development of such structurcs in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Arch-butt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a considerable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it & worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c. c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric acid soliltion.

Jan 1, 1925

By R. W. Smith, K. H. Lee

Bond type simulated closed-circuit grindability tests and batch grindability tests were run on six pure minerals plus a limestone and a taconite ore. The simulated closed-circuit tests were made at five different meshes of grind. The minerals tested varied widely in hardness and breakage pattern. For all simulated closed-circuit tests both Bond and Holmes work indices were calculated and compared. The Bond grindability testlm6 has been widely and quite successfully used for predictions of such items as ball mill power requirements and as an aid in plant comminution equipment selection. The test is interesting in that although run as a series of batch tests it is over-all a simulated closed-circuit test with a circulating load of 250%. The simulated closed-circuit feature is probably the primary reason for the notable success of the test. Perhaps the major criticism that can be brought against the test is that it is time consuming, since it normally takes a trained technician about an eight-hour shift to perform it.4 For many purposes this is an acceptable time requirement. However, if a grindability test is to be used for mill control purposes it should be performed in as short a time interval as possible, preferably under an hour. Sometimes in industry strictly batch tumbling mill tests are run and an attempt is made to correlate such batch tests with plant mill operation. Then an attempt is made to adjust operating tumbling mills based on data from the tests. The tests, however, frequently do not correlate well with operating data. The purpose of the present work was to explore some of the similarities and differences between a simulated closed-circui.t grindability test and a batch type test. Six different minerals plus a limestone and a taconite ore were tested in the experimentation. These materials varied widely in hardness, breakage characteristics, etc. Standard dry Bond grindability tests were mn on all materials at 48, 65, 100, 150 and 200 meshes of grind. Feed material was prepared by stage cmshing to -6 mesh. Initial feed volume was 700 cc. Care was taken to maintain the standard constant weight (about 20125 gm) and number of balls (283) during all the tests. Rotational speed was 70 rpm. Table I lists the materials studied along with pertinent data regarding the materials and Bond grindabilities obtained. In addition, dry batch tests were performed on all materials. These tests were made in the same mill as was used for the Bond tests. An identical ball charge and an identical feed volume were used. After rotating the mill for a predetermined number of revolutions at the same rotational speed as for the Bond test, the material was removed and separated from the ball charge. A screen analysis was performed on this product. Knowing the original size distribution of the feed and the size distribution of the product, it was possible to calculate the grindability or grams of a particular mesh produced per revolution of the mill. After the screen analysis of the product, the various fractions were recombined and placed back in the mill for further grinding. After grinding for additional revolutions of the mill the procedure was repeated. Thus, it was possible to obtain grindabilities for each material at a number of meshes of grind and for various revolutions of the mill. Grind-abilities obtained from batch tests are shown in Table 11. COMPARISON OF BOND AND BATCH GRINDABILITIES Figs. 1A through 1D show relationships between batch and Bond grindabilities. Figs. lA, lB, 1C and 1D show respectively graphs indicating the relationships for batch tests run for 100, 300, 500 and 700 revolutions of the mill. For a particular material on each graph, points are shown for 200, 150, 100, 65, and 48 meshes of grind except for several missing coarse meshes of grind for galena which did not fall conveniently on the figures. For each material and graph the point nearest the origin is for 200 mesh, the next for 150 mesh, the next for 100 mesh, etc. Considering Fig. lA, it is interesting to note that all relationships shown are essentially straight lines. There are, however, considerable differences

Jan 1, 1969

By E. L. Dougherty, J. W. Sheldon

A numerical method for computing the dynamical behavior of fluid- fluid interfaces is described. Results of studies made to assess the accuracy and economy of the method on a computer are reported. It is concluded that it is practical to obtain digital computer solutions for fluid- fluid interface problems with two space dimensions. PROBLEM DEFINITION We consider two-dimensional flow in a rectangle as shown in Fig. 1, where a fluid-fluid interface divides the rectangle into two regions. The pressure is specified along the lower boundary (the injection boundary) and upper boundary (the withdrawal boundary). There is to be no flow of fluid across the side boundaries, which are walls of symmetry for the flow, and px = 0 along these boundaries. The fluids are incompressible, the absolute permeability and porosity is constant, and each fluid has its own constant mobility. Thus, the pressure satisfies Laplace's equation in each region. Across the interface, pressure is continuous and the normal component of fluid flux is 1. These conditions are shown in Fig. 1. The velocity of a point on the interface in the direction of the normal from Fluid 1 into Fluid 2 is U,/ Q, where Un is the normal component of volumetric flux at the point on the interface, i.e., For brevity, we call the problem defined above "Problem A". Problem A is a simple example of a dynamical fluid-fluid interface problem. However, the same numerical methods which we use to solve Problem A can be extended to the solution of a large number of fluid-fluid interface problems which are mathematical models for various oil recovery processes,l hence our interest in Problem A. We define the interface by prescribing the x, y coordinates of a finite set of points. These points are called "interface mesh points" and are illustrated by triangles or asterisks in the figures. Fig. 2 is a procedural (flow) chart displaying the main steps in the solution. We comment briefly on some of these steps in this section and then give further details in subsequent sections. For mobility ratio greater than one it is well known that Problem A is unstable.*2 Small amplitude,

Jan 1, 1965

By W.M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By Robert S. Williams

On several occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825" C. and is then reheated, the writers have noticed that reerystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens 1 in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840' C. for 2 hr. and then quenched ' in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen and duplicate observations were possible. The specimens were held at the reheating temperatures for periods of 15 min., 30 min., 1, 2, and 4 hr. All specimens were etched with a freshly prepared mixture of equal volumes of concentrated NH4IOH and H2O2.

Jan 1, 1924

By W. M. Peirce

The present work has been done in an endeavor to correlate and complete the data on the constitution of alloys of zinc with other common metals, dealing exclusively, however, with the zinc-rich alloys in which the zinc content is between 90 and 100 per cent. This investigation has included the systems lead-zinc, cadmium-zinc, iron-zinc, copper-zinc, aluminum-zinc, nickel-zinc, manganese-zinc, cobalt-zinc, tin-zinc, and magnesium-zinc. The important ternary system zinc-lead-cadmium and the zinc corners of other ternary systems have been investigated in connection with this work but will not be dealt with here. Zinc does not form a single homogenous zinc-rich solid solution over any considerable range of concentration with any of the metals mentioned. A limited range of solid solubility is said, by previous investigators, to occur in several cases and certain effects on the properties of zinc are attributed (with varying degrees of consistency among different writers) to the presence of certain other metals dissolved in zinc. The increasing use of rolled zinc and the possibilities offered by zinc as a casting alloy in certain fields have made it essential to determine precisely these equilibrium relationships. In carrying out this investigation reliance was placed chiefly on two methods, conductivity measurements and microscopic analysis. The first method proved valuable in determining the existence and extent of solid solubility. The second method stands alone as a means of determining structural characteristics and supplements the first method in the measurement of solid solubility. The scleroscopic hardness of all conductivity specimens was measured partly for its value from the point of view of mechanical properties and partly as a check on the conductivity curves in indicating the limits of solid solubility. No hardness curves are included in this paper, for in no case were they important in arriving at the constitution of any system. Conductivity measurements were in all cases made on cold-rolled strips 0.020 in. thick and 0.5 in. wide, both as cold rolled and after an

Jan 1, 1923

By David B. Brooks

INTRODUCTION Resources are not; they become (Zimmermann 100) . The companion concepts of reserves and resources appear, one way or another, in almost all considerations of mineral supply. Yet, no other concepts in the economics of the mineral industries have occasioned so much confusion. Whereas everyone agrees that in general the terms refer to the amounts of material that-depending upon technology, market conditions, and institutions-will become available for production in the near or more distant future, the apparent agreement disappears when we come to more specific definitions or to application of the definitions. Some definitions emphasize the physical aspects of reserves and resources, while others emphasize the economic. Some treat reserves and resources as fixed quantities, while others regard them as continually varying. Some consider that reserve and resource estimates have validity only for individual deposits, while others insist that they can be measured with sufficient accuracy for regional or national planning. This confusion in concepts that lies at the very heart of mineral economics is both strange and not so strange. It is common in the social sciences to find concepts that have been adopted into scientific jargon from popular usage and given rather special meanings -at the same time that they continue to be widely used without such qualifications. Psychologists have the same trouble with personality and sociologists, with community. Nevertheless, an attempt must be made to straighten out the various meanings of reserves and resources, or at least to clarify the conditions under which different meanings are applicable, before much progress in analysis of mineral problems can be expected. That is the objective of this chapter. Throughout the chapter, an attempt has been made to provide enough references to guide the interested reader to the most pertinent works on the concepts under study. However, even in a review article, it is no longer feasible to provide a comprehensive set of citations; there are simply too many. In many instances the works cited will themselves include the bibliographies needed to complete a literature search; those that are particularly useful in this respect are so noted. Also, because of the limited availability of foreign periodicals, some important works -originating largely in Canada, France, the

Jan 1, 1976

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By L. F. Mondolfo, B. E. Sundquist

The undercooling associated with the nucleation of the secondary phase from the liquid by the solid primary phase was studied in sixty binary alloys by means of a hot-stage microscope. It was found that in a system of a and ß, a usually nucleates ß at low undercoolings, but ß does not nucleate a, except possibly at undercoolings approaching homogeneous nucleation. This behavior can be explained in terms of relative interfacial energies and shows that crystallographic disregistry is only a minor factor in heterogeneous nucleation from metallic liquids. PREVIOUS experimental work1-6 on nucleation of solids from liquids has shown that normally nucleation is heterogeneous, and that small solid particles present in the liquid are responsible for the nucleation. These experiments and the theory that has evolved from them have made apparent that there is a "characteristic undercooling" associated with the nucleation of the solid from a given liquid by a given impurity. Little is known, however, about the chemical and structural relationships between the nucleating agent and nucleated solid that control the effectiveness of the nucleating agent in catalyzing the nucleation, as measured by the required undercooling. A review of the literature has yielded seventeen undercoolingsL-6 for the nucleation of solid from liquid metals by "known" nucleating agents. All values come from experiments in which the metal studied was divided into a number of particles (10 to 300 pin diam.) much larger than the number of extraneous impurity particles so as to obtain a large number of particles free of foreign nucleating catalysts. Known nucleating agents are then introduced by coating the droplets with particles or a thin film of the catalyst. Six of the seventeen undercooling values referred to cases where, for various reasons, the identity of the nucleating species was not at all certain. Another six cases involved nucleating agents with a crystal structure that was not known. Four other cases involved undercoolings listed as greater than or equal to undercoolings which were very likely those for homogeneous nucleation. One investigation3 involved adding to droplets powdered oxides, carbides, and so forth that were doubtlessly covered with adsorbed oxide or nitride films. The highly variable nature of these films resulted in highly variable undercooling (as was also found in preliminary work in this investigation). It is apparent that the information on heterogeneous nucleation in liquid metals is too limited to give rise to any definite conclusions on the nature of the catalytic process. With these problems in mind a new method was

Jan 1, 1962

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By W. F. Stowasser

downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in cooperation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace. Process Description The first of two process steps incorporates the art of balling and prepares the concentrates for burning. The second step consists of burning the green balls on the grate machine to the hardness required for shipping and handling purposes and for reduction in blast furnaces, see Fig. 1. Facilities are provided at the pilot plant to receive carload quantities of concentrate. The concentrates are loaded into a 50-ton bin direct from railroad cars. Because of the variable moisture content of the concentrates after shipment in an open railroad car it is necessary to repulp and refilter the concentrates to maintain a uniform and proper moisture content for the balling operation. Concentrates are conveyed to slurry tanks, and the slurry, at 50 to 60 pct solids, is pumped to a 4x4-ft drum filter. The filter provides feed of uniform moisture to the plant. Magnetite concentrates are normally filtered to produce a cake containing about 10 pct moisture, a necessary requirement for the following balling operation. The filtered concentrate is conveyed to a rotary bin table feeder which acts as a surge bin for the filter cake and delivers a steady flow of concentrates to the balling drum. It is often desirable to make additions to the concentrates as they are fed to the balling drum. These additives, such as bentonite, increase the strength of the finished green pellet and improve ballability of the concentrate. A vibrating feeder supplies additive to the feed belt, and the additive is mixed with the concentrate in the balling drum. The balling drum, shown in Fig. 3, is 8x3-ft diam. An oscillating cutting bar maintains the lining in the drum by trimming off the buildup of excess concentrate as it forms. The drum is operated in closed circuit with a lx4-ft rod-deck vibrating screen. Undersize pellets or seed pellets from the screen are returned to the balling drum until they grow to the desired size. Size of pellets is controlled by the opening in the screen deck. The formation of pellets in the balling drum is affected by many variables. Some of these are: the size distribution of the feed, the particle shape of the concentrate, the feed rate to the drum, the moisture in the concentrate, the speed of rotation of the drum, the slope of the drum, and the type of trimming obtained with the cutting bar. In this process, attempts are made to control the pellet size within the limits of % to 5/8 in. diam. The screened oversize pellets are conveyed under a coal feeder where sufficient powdered coal is added to the belt to produce desired results in the burning process. The top size of the coal successfully used has been 20 mesh, and anthracite was used in the test program. Fig. 4 illustrates the vibrating screen and the coal feeder. The pellets and free coal are conveyed together to the 5x3-ft diam- reroll drum that rolls the coal onto the surface of the pellets. This drum is also equipped with a cutting bar. The prepared pellets, containing bentonite, water, and surface coal, are elevated to the traveling grate, which consists of a continuous strand of 37 pallets. Each pallet, with a grate bar area 2 ft wide by 1 1/2 ft long, has 14-in. high side plates, Fig. 5. Feeding and distribution of the green balls to the grate is handled by a short conveyor which oscillates back and forth across the 2-ft width of the grate. An adjustable vertical plate located several inches in front of the head pulley of the oscillating conveyor controls the height of the bed and levels the moving bed of pellets. This method of feeding prevents segregation of various size pellets as well as fines and produces a uniform, permeable bed. The pallet train moves under the furnace and across four windboxes, located beneath the pallet frames, see Fig. 2. As the green pellets are deposited on the grate, partial drying of the pellets begins over a 2-ft long updraft windbox. The low temperature air reduces the moisture in the pellets in the lower level of the bed and this operation is essential to prevent sagging of the bed during later stages of the Process. The air used for this drying is recuperated from cooling the pellets on the grate, and supplemental heat, required for starting the Process, is obtained from an auxiliary burner. The pellets are then moved by the grate into the furnace and over an 8-ft windbox, designated as the downdraft waste windbox. Products of combustion are exhausted from this windbox to atmosphere. The furnace, shown in Fig. 6, is constructed with three chambers to provide downdraft drying, preheating, and ignition, respectively, to the pellet bed as it passes through. Overall length of the furnace is 5.57 ft; however, the exterior wall ends may be moved to reduce the length and also adjusted to Obtain the bed height desired, The drying, preheating, and ignition sections of the furnace are supplied with medium temperature

Jan 1, 1956

By M. J. Duggin

Structural similarities between the E, X, and iron carbides are illustrated. Experimental evidence regarding phase transformations occurring during ternpering reactions in finely divided carbides, thin-film carbides, and carbides which occur in steels is considered and possible mechanisms for the E — x and x — 9 transformations proposed. HOFER1 has shown that within the appropriate temperature ranges carbon monoxide will react with finely divided a iron to form either iron carbide or x iron carbide. He has shown that at an elevated temperature the E iron carbide will transform to the x iron carbide (Hagg carbide) which, upon further elevation of temperature, will transform to 9 iron carbide (cementite). Jack,2,3 using X-ray diffraction methods, has observed that during the tempering reactions occurring in steel the E iron carbide formed in the first stage of tempering passes into two-dimensional platelets of 0 iron carbide during the second stage of tempering. The three-dimensional form of the 0 carbide is formed during the third stage of tempering. Jack suggested2 that the two-dimensional platelets of 0 carbide could be related to the faulted x iron carbide. Okada and Arata4 investigated a Swedish steel containing 1.05 wt pct C and approximately 1.0 wt pct Mn using permeability measurements at low field strength. A Curie point of 360°C was observed in the quenched steel, which indicated the presence of E iron carbide. On tempering at 400°C the specimen developed a Curie point at 230°C, indicating the presence of x iron carbide, and on tempering at 700°C the specimen developed a Curie point at 190°C which was assigned to 0 iron carbide. The carbides were extracted electro-lytically and the use of X-ray diffraction techniques4r5 indicated the carbide with a Curie point of 230°C to be x iron carbide. The Curie points of the carbides are 10 to 22°C lower than the accepted values which is probably due to the presence of manganese in the carbides, since it has often been observed (e.g., Ref, 6) that a partial substitution of manganese for iron in cementite will lower the Curie point of this carbide. Hofer' summarizes additional evidence of the tempering reactions in steel in which E iron carbide, formed during the first stage of tempering, transforms to x iron carbide during the second stage of tempering. During the third stage of tempering, the x carbide disappears as the 0 carbide is formed. By carburizing thin iron films in a CO gas stream, ~a~akura' has been able to produce the E, X, and 0 iron carbides. He found that below 250°C the E iron carbide was formed; between 250" and 350°C the x iron carbide was formed and above 350°C the 0 iron carbide was formed. He has shown that the E iron carbide transforms to form x iron carbide at 380" to 400°C and that the x ir°n carbide transforms to form the 0 iron carbide at approximately 550" C; both of these phase transformations are irreversible. Hofer' presents a review of evidence to show that the sequence of reactions occurring during tempering processes subsequent to the formation of E iron carbide formed by the direct carburization of finely divided a iron is the same as the sequence of reactions which occur during the tempering processes subsequent to the formation of E iron carbide in steel during the first stage of tempering. It is evident from Nagakura's work that identical tempering reactions are found in thin films of iron which have been carburized to form iron carbide. The purpose of this paper is to discuss the structural similarities between the E, X, and 0 carbides and to suggest a possible mechanism by which regions of the E carbide, formed during the first stage of tempering, may transform to the x carbide during the second stage of tempering. For the finely divided or thin film carbides a mechanism will be proposed for the transformation of the x carbide to the 0 carbide during the third stage of tempering, although it will be suggested that there is evidence that such a transformation may not occur in steels. STRUCTURAL DATA OF THE E, X, AND 0 IRON CARBIDES € Iron Carbide. It is evident from X-ray diffractions and electron diffraction', investigations that the metal atoms in the E iron carbide form an hcp structure with lattice constants ah = 2.752A, ch = 4.3534, using electron diffraction, reports the lattice paramet$rs of the superlattice cell to be a = 4.767A, c = 4.354, c/a = 0.9134. He finds that the carbon atoms occupy the octahedral voids in the metal atom structure so as to form a hexagonal stacking sequence with its basal plane parallel to that of the metal atoms. Considerable long-range disorder occurs in the positioning of the carbon atoms, however, which is in agreement with the possible range of composition Fe2C-Fe3C discussed by Hofer.' Barton and ale" have made X-ray diffraction measurements on a sample of E iron carbide extracted from a catalyst in an organic process. Although there were few reflections recorded on the obtained X-ray powder diffraction pattern, they have proposed that the structure could belong to one of the three possible space groups p3m1, P63/mmc, or Pbcn if one assumed the composition to be Fe2C. Nagakura, using electron diffraction data, suggests a space group of P 6322 for a specimen of c iron carbide of apparent composition Fez.&. x Iron Carbide. The x iron carbide has been studied by Duggin and Hofer" and by Jack and wild,' who

Jan 1, 1969

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800's, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By S. E. Maddigan

MANY experimental and theoretical investigations have been made on the processes involved in annealing and recrystallization of metals. Most of these, however, have treated the time element as constant and heat-treatments used have been for relatively short times. Aside from the early work by Carpenter and Elam,1 the few that have investigated the effect of time on the processes have usually done so for fairly short time periods. During recent years the growing interest in long-time creep properties of metals and alloys under stress has made increasingly important a better knowledge of the recrystallization during prolonged heating. The recrystallization temperature of 70-30 brass given by Clark and White2 in 1932 was somewhat above 400°F. (204°C.) but under 500° (260°C.), whereas in our laboratory recrystallization has been observed in creep specimens at 204°C, the lowest temperature of Clark and White's range. Since the creep properties are quite different above and below the recrystallization temperature, erroneous conclusions can readily be drawn by the application of short-time recrystallization data to creep problems. It was thus considered of both practical and theoretical value to make long-time annealing studies near the minimum recrystallization temperature. In this way useful additions could be made to data on recrystallization temperatures and, since the reactions in this range are relatively slow, additional insight could be obtained into the factors involved in annealing. Several comprehensive reviews of recrystallization processes have been written,3-5 therefore only a brief review of the generally accepted facts will be given here.

Jan 1, 1940