Search Documents

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By R. W. Raymond

Under the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been, that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them—Texas—came into the Union by its own voluntary

Jan 1, 1913

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By C. A. Heiland

Measurements of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for comprehensive engineering information on the subject. The working principles of a number of gravimeters will be illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as elementary form as possible. A description of calibration methods constitutes the last part of the paper. The symbols shown at the top of page 197 will be used in equations throughout the paper. Dynamic and Static Gravity Methods Methods of measuring gravity fall into two groups: dynamic and static methods. The first group involves the measurement of time. Examples are: determinations of the period of oscillation of a pendulum, measurements involving the free fall of a body, and comparisons of gravity with the centrifugal force of a rotating body. Measurements in the second group of gravity methods are concerned with deflections of certain indicators when the force of gravity is in equilibrium with another comparison force.

Jan 1, 1940

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal.

Jan 1, 1943

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

A LARGE attendance at the annual dinner of the Institute, to be held this year on Tuesday eve-ning of convention week, is already assured. Presentation of the Douglas, Hunt and Saunders medals will attract unusual attention since not only in Blaylock, Mathews and Hoover the Institute will be honoring men who have made notable contributions to the advance-ment of their profession, but as to one of them each person as he passes down the reception line will be won-dering whether in renewing acquaintance with our past-president and present Secretary of Commerce, he is not greeting the next president of the United States. Elsewhere in this issue accounts of the professional careers of these three men appear as also of the two younger men, Charles H. Herty, Jr., and P. H. Royster, who are to receive the Robert W. Hunt and the J. E. Johnson awards. Institute honors go for technical achievement, but the Institute will be proud and happy if the nation should later confirm its own judgment by placing larger responsibilities on one of its members. The medals are to be presented at the annual dinner following the President's reception and preceding the dance. There will be no. other speeches and since the occasion falls on Carnival Night a particularly gay evening is anticipated. The event will be at the Wal-dorf as usual, and members are urged to return prompt-ly the reservation cards sent them by mail. Other entertainment features will include a Smoker, Monday evening at 8.15, held at Mecca Temple and in charge of a new committee with Fred Kay of the Petro-leum Division as chairman. He promises that vocal music will not be allowed to interrupt conversation. Lunch will be served each day on the Fifth Floor of the Engineering Societies Building, and ten special luncheons and dinners have been arranged for particu-lar committees and groups as shown by the detailed program. The Woman's Auxiliary has laid out a gen-erous program including luncheons, teas, a theater party on the night the men folks go to the Smoker, visits to museums and, not the least important, a round of the leading shops. The Excursion Committee is arranging for an excur-sion sure to be of interest. The American Smelting and Refining Co. has opened its great Perth Amboy plant to the Institute, and on Thursday, Feb. 23, a party will be taken to it by bus traveling through the Holland Tunnel en route. Full opportunity will be afforded those interested to see the workings of the ventilation system of that great public work. If a sufficient number indicate interest, arrangements will be made for group excursions to other plants in the vicinity of the city.

Jan 2, 1928

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By J. H. East, E. R. Maize

INTRODUCTION PROBABLY no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines, testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. So far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. ADJUSTMENTS OF DIESEL ENGINES FOR UNDERGROUND USE A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn 1 lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:I, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Diesel operates in confined places should contain less than 1/2 pct of carbon dioxide and at least 20 pct of

Jan 1, 1947

By B. D. Cullity, S. S. Hsu

The stress distribution at the surface of a twisted cylinder is analyzed along the boundary of a slip plane of arbitrary orientation and this analysis is applied to the torsion of cylindrical crystals of magnesium. A criterion for slip is developed and the critical resolved shear stress of magnesium in torsion is found to be 0.038 kg per sq mm. The mechanism of torsional deformation in magnesium and aluminum is described, as well as the relaxation of a twisted crystal at elevated temperatures. THERE has been considerable fundamental study A of the mechanism of slip occurring during deformation in tension and compression but comparatively little attention has been paid to the mechanism of torsional deformation. This paper is concerned with the way in which a single crystal deforms in static torsion and with the phenomenon of untwisting which a twisted crystal undergoes during annealing. Particular attention is paid to the application of the critical resolved shear stress law to torsional deformation. Probably the most likely mode of torsional deformation that can be imagined consists of rotation of one part of the crystal relative to another on the active slip plane. Here the most interesting feature is the slip direction. If a cylindrical single crystal is twisted about its axis and if, to consider the simplest case, the active slip plane is normal to the specimen axis, then the direction of gross slip at any point must always be at right angles to the radius drawn to that point. It follows that the crystallographic direction of slip must be continually changing, in sharp contrast to slip in tension which occurs in a crystallographically constant direction. Extensive investigations of slip in torsion have been made by Gough and his associates.' They made torsional fatigue tests on metal single crystals belonging to a number of different crystal systems and observed, with a microscope, the appearance of slip lines on the surface and of strain markings on the transverse cross section of cylindrical specimens. They concluded that the critical resolved shear stress law was just as valid in torsion as in tension, in the sense that slip occurred on that plane and in that direction in which the resolved shear stress was a maximum. They also established that the operative slip planes and directions were the same as in tension. They did not, however, measure the critical resolved shear stress in torsion nor, in fact, did they establish that a critical value of the resolved shear stress was necessary for the initiation of slip. Their investigations were, moreover, restricted to torsional fatigue tests which necessarily involve small strain amplitudes. Wilman,' studying crystal growth and the abraded surfaces of crystals, observed crystal fragments

Jan 1, 1955

By C. E. Sims, G. A. Moore

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By E. S. Davenport, R. J. Hafsten, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By R. J. Hafsten, E. S. Davenport, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By Clarence Seyler

THE technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter1 published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and cannels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened' with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 c.c of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 3, 1925

By A. U. Seybolt, J. L. Walter

The effects of the addition of 0.5 pct ThO2 (by volume) on the grain structure and texture of heavily rolled tungsten sheet were studied. Powder metallurgy ingots were rolled to sheet, 0.001 in. thick, and samples were annealed at temperatures from 1200" to 2500°C. The heating rate to the anneal temperature was varied from 3°C per min to 6500°C per min. The orientations of the largest grains were determined by X-ray diffraction. The disposition and loss of the ThO2 particles were determined by electron transmission microscopy and the activation energy for remozlal of the thorium was measured by mass spec-troscopy. Heating rates below about 800 C per min produced large, highly elongated grains. Higher heating rates produced much smaller, less elongated grains. The grain structure and texture of the slowly heated samples were identical to the structures and textures of heavily rolled tungsten foil conventionally doped with aluminum, silicon, and potassium but the recrystallization temperature was about 200°C lower. There was stringer-like dispersion of larger ThO2, particles superimposed on a uniform dispersion of fine particles. The particles increased in size and decreased in number with time at temperature. The loss of particles was accompanied by formation of grain boundary voids and surface pits. The activation energy for removal of the ThO2 was about 40 kcal per mole. THE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of heavily rolled sheet1 or drawn wire."4 Thus, "doped" tungsten sheet, rolled to 0.001 in. and recrystallized, develops a structure consisting of large, highly elongated grains of a specific preferred orientation.' It has been shown that the elongated grain structure was caused by a dispersion of particles, identified as mullite (Al6si2O13),1,4 in strings parallel to the rolling direction in sheet or to the wire axis. Identical results were obtained for iron which was doped with glass and rolled to 99 pct reduction of thickness and recrystallized.5 Again, the glass particles were disposed in strings parallel to the rolling direction. The strings retarded boundary migration in the lateral direction but grain growth was able to proceed relatively unhindered along the direction parallel to the strings.1,5 In both the doped tungsten and the glass-doped iron, the particles were highly plastic during the high-temperature deformation. Since mullite melts at about 1800°C and the glass employed melts at about 810ºC, the particles were probably molten during the recrystallization anneals (above 1800°C for the doped tungsten and 850°C for the glass-doped iron). There are indications in the literature that particles not plastic at hot-working temperatures (up to about 1550°C for tungsten) may also impart elongated grain structures by primary recrystallization of worked alloys. Examples are dispersions of tantalum carbide in chromium,6 and ThO2 in nickel where elongation ratios of recrystallization grains of up to 20:l were obtained.7 Strings of ThO2 particles in W-ThO2 wire have been seen by Rieck.8 In view of the available evidence, it was of interest to extend the previous studies of doped tungsten and glass-doped iron to include W-ThO2 sheet materials. Of specific interest was the grain structure, preferred orientation, recrystallization temperature, and disposition of the thoria particles. EXPERIMENTAL PROCEDURE A) Material Preparation. About 380 g of blue tungsten oxide (approximate composition WO3) was wet with a sufficient amount of aqueous solution of Th(N03)4 to provide 0.5 vol pct ThO2. The wet mixture was stirred to distribute the doping material uniformly throughout the powder. Stirring was continued while the mixture was heated until it was completely dry. The dried, doped mixture was then reduced to tungsten powder by heating at 850°C for 2 hr in a stream of dry hydrogen. The doped tungsten powder was hydropressed in a rubber sack at pressures of 50,000 psi to produce an ingot approximately 2 cm diam by about 5 cm long. Next, the pressed cylinder was heated in hydrogen for 2 hr at 1350°C to render it strong enough for machining. The cylinder was machined to a square cross section of 1.6 by 1.6 cm with rounded corners. Finally, the bar was heated for 2 hr at 2150°C in hydrogen to provide a sufficiently dense mate rial to withstand the hot-rolling operation. Prior to rolling, the ingot was reduced in thickness by about 20 pct by forging at 1550°C. This served to increase the density of the material and to widen it slightly for better rolling characteristics. The forged ingot was then rolled at 1550°C to a reduction of 45 pct of thickness, following which the rolling temperature was reduced to 1300°C and the slab rolled, with several reheats, to 0.050 in. Further reduction was accomplished at 800°C in tungsten sheet packs to a total reduction of about 99.85 pct. B) Annealing Treatment and Observation of Structure. Small samples of the rolled foil were annealed in one of two ways. Some of the samples were suspended in a covered tungsten can and annealed at temperatures from 1200" to 2200°C for various times in vacuum of l0-7 to 10-6 mm Hg. The can was heated by induction and temperatures were determined by optical pyrometry

Jan 1, 1970

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,' and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By G. J. Heuer, J. N. Dew, G. C. Clark

The effect on well behavior of partial permeability barriers, changes in producing rates and well spacings have been calculated through use of a radial, unsteady-state, two-phase-flow mathematical model. This model allows for variations in permeabilities and porosities with distance from the wellbore. The numerical methods necessary to solve the problem require use of a highspeed digital computer, in this case an IBM 704. In each instance, pressure and saturation gradients, gas-oil ratios and recoveries around a well producing by solution-gas drive have been calculated as a function of time and distance from the wellbore. Comparisons are made to show the effect of changes in producing rate and of varying permeability near the wellbore and out in the formation on the production and pressure history of the well. The effect of different well spacings on producing rate and ultimate recovery is considered. Although the mathematical description of the reservoir is simplified in comparison to an actual reservoir, the results do give some insight into the difficult problem of spacing and proration in a heterogeneous solution-gas-drive reservoir. Results show that for the cases considered spacing has little effect on ultimate recovery and that permeability barriers removed from the well decrease producing rate for a period of time but have only a small effect on ultimate production. INTRODUCTION The effect of spacing and producing rate on the production characteristics and ultimate recovery of a well producing by the solution-gas-drive mechanism have been topics of interest to the oil industry for many years and the subject of many hearings before state regulatory bodies. The problem is very complicated because of the difficulty of simulating in the laboratory a reservoir producing by the solution-gas-drive mechanism under anything like normal field conditions. This paper gives the initial results of a study aimed at determining the effect of these factors on production from reservoirs simulated by a mathematical model. Two-phase, unsteady-state equations are used to calculate pressures, saturations, and rates of oil and gas flow as a function of time and distance from the wellbore. The model is radial, and reservoir properties may be varied with distance from the wellbore. A decrease in permeability at a given distance results in a low-permeability ring concentric with the wellbore through which all the fluids from more distant portions of the reservoir must flow. The current mathematical model allows for variation of permeability, porosity and saturations as a function of distance from the well. Any desired drainage radius for the well may be selected. Drainage radii of 745 and 1,053 ft, which correspond to 40- and 80-acre spacing, were chosen for the calculations which follow. A large amount of the input data has been held constant. No investigation was made into the effect of changes in fluid properties and relative permeability characteristics on oil and gas production behavior. Fluid properties and relative permeabilities are essentially those of the White Mesa portion of the Greater Aneth area in southeastern Utah. A recently concluded hearing before the Utah Oil and Gas Conservation Commission to determine spacing for the field aroused interest in the possible effect of permeability constrictions located some distance from the well on production and recovery. This interest stimulated the present study. In this paper, no attempt has been made to simulate any field production characteristics exactly. Only the solution-gas-drive mechanism has been investigated, and production by liquid expansion has not been considered. This investigation is exploratory in nature but does give some insight into the problems of spacing and proration in a solution-gas-drive field having permeability variations. THE MATHEMATICAL MODEL The mathematical model is similar to that proposed by West, Garvin and Sheldon.' Approximately the same techniques have been used in arriving at a solution. The equations are nonlinear, partial differential equations which have been known for some time. The particular equations used for this study neglect the effects of capillary pressure and gravitational forces. The advent of modern digital computing equipment has made their solution practical. Basically, the method solves for pressure, saturations, and oil and gas flow rates as a function of distance and time. In our model, distance to the

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to sup- ply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their useful life; however, the partial redesign

Jan 1, 1964