Search Documents

By L. S. Darken, H. A. Wriedt

THE constitution diagram of the iron-copper system derived by Daniloff' exhibits, at the iron-rich end, phase fields similar to those of the iron-carbon diagram. At 1484° 1094°, and 850°C there are, respectively, a 6-y-L peritectic, a y-E-Lperitectic, and a a-y-E eutectoid. The phase designated E is copper-rich, containing 4 pct Fe or less according to the temperature. The composition of copper-saturated ferrite (a-solid solution) has been determined previously only twice as a function of temperature. By electrical conductivity measurements, Buchholtz and Köster2 found 3.4 pct Cu in ferrite at a eutectoid temperature of 810°C. They represented the composition of saturated ferrite by the equation, log (%Cu) = 4.32-4125 (1/T) Gregg and Daniloff3 reported that Köster later modified his opinion, raising the indicated eutectoid temperature to 833 °C and the copper content of eutectoid ferrite to 3.7 pct. The literature contains several indications4-7 that the work of Köster and his co-workers is not reliable. Norton,8 using an X-ray method, found that 1.4 pct Cu dissolved in ferrite at the approximate eutectoid temperature of 850°C and that the solubility decreased to about 0.3 pct at 700°C. Below 700°C his experimental data show almost no change in solubility. These findings, although inconsistent with the work of Ruer and Goerens4 and of Smith and Palmer,7 have been used generally since their publication. In investigations involving the observation of arrests in temperature during continuous heating or cooling the precise location of the eutectoid temperature has been obscured by a large hysteresis. The more reliable work 579 where the results are not effected by this hysteresis indicates a eutectoid temperature between 840° and 850°C. The foregoing discrepancies, along with a few observations in this Laboratory relating to the precipitation of copper from ferrite, prompted us to rein-vestigate the lower temperature portion of the Fe-Cu system. In this investigation the solubility of copper in ferrite was obtained by the chemical analysis of high-purity iron equilibrated with copper-silver alloys. This method eliminated the necessity for retaining by a quench the physical state of the specimen existing at the equilibration temperature. EXPERIMENTAL The reaction of the iron with the copper alloy was

Jan 1, 1961

By R. S. Handy

DOES hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Coeur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 1 ½ -in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgically moree canonical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 1 ¼ -in. opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in hand-sorting, then, it must lie in the metallurgical results achieved.

Jan 4, 1918

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

By Zay Jeffries

IT has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500° C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.1 The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 lb. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is affected in an electric furnace in an air atmosphere,

Jan 9, 1919

By Dr. O’Neil Thomas J., Donald W. Gentry

Pure gold was hidden in the quartz, they said, 'Twas proved by dreams and signs, and rods divining, By chemic tests, and spirits of the dead, In fact by everything-except by mining. " from R.E. White, "The Mining Town," Alta California, August 18,1873 Textbooks in mining engineering have traditionally covered ore reserve estimation and mine valuation in a single volume. Indeed, Examination and Valuation of Mineral Property by R. D. Parks (1957), having been the standard of the profession for over 20 years, is a classic example. However, the state of knowledge in these two fields has grown tremendously. Most mining engineering curricula now cover these topics in separate courses, and in practice, these tasks are usually performed by different individuals. Thus, this trend now suggests the need for separate, specialized publications rather than a single volume for both topics. Because of the separate development of the science of ore reserve estimation, it is important to state at the beginning what this chapter does not cover. It does not address in detail the design of sampling programs, sampling methods, or the processing of samples or sample data compilation. There are a number of suitable references available on these topics, including Peters (1978), Gy (1979), as well as the previously cited book by Parks. Furthermore, this chapter does not cover in any substantial detail either the traditional methods for using sample data to calculate ore reserves or the more recently developed geostatistical methods. The traditional methods are thoroughly covered by Popoff (1966) and more concisely by Barnes (1980). Among the more useful references for statistical applications in ore reserve estimation are Barnes (1980), David (1977), and Clark (1979). A thoughtful review of the entire science and art of ore reserve estimation is provided by King, McMahon, and Bujtor (1982). In spite of the fact that expansion of knowledge now calls for separate books on ore reserve estimation and financial evaluation, neither publication can ignore the important interrelationships between the two fields. In regard to this text, the unique and crucial role of ore reserves can not be omitted entirely; however, the field is now simply too extensive to treat here in any comprehensive manner.

Jan 1, 1984

By Ivan E. Goodner, Charles H. Fulton

The subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,' Belles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the snlphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to' date no effort has been made to correlate the data obtained in the latter researches and apply them to the study of the product called " matte," which is made in such large quantities by copper- and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead-iron mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections: I. A review and discussion of the various binary systems of the metallic sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical properties of these sulphides. II. A description of the results obtained from the chemical and microscopic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Jan 1, 1909

By Charles M. Romanowitz

The motivation for the art of dredging for placer mining can be compared in a slight degree to the spread of civilization which started in the Near East and spread both east and west. Dredging started with the "bag and spoon" dredge in the lowlands of Europe reportedly about 1565, went southeast to New Zealand where designs were developed for a bucket-line mining dredge known as the New Zealand type, and westward to the eastern United States where a dredge was developed and used exclusively for excavating. Then it moved to Montana, where it was first used for mining in 1895. The New Zealand-type dredge was imported into California in 1898 (Fig. 1) and was followed shortly by the Montana design. As today, these early dredges were equipped with continuous bucket- line chains, a treatment plant, and a means of waste disposal mounted on a wooden hull. Both types of dredges are complete mining units: they dig the formation, transport the dug materials, and concentrate the valuable ore. After sizing, the fines containing the ore are passed by gravity to the treatment unit, while the barren materials are discharged overboard. By digging the materials to be treated at the bow and depositing all the waste, at the stern, the dredges automatically advance to new reserves without presenting any transportation problems. The main differences between the two types are in the method of holding the dredge in the digging position and in the disposal of the tailings to the rear. The New Zealand type (Fig. 2) uses the headline system with a bow anchor for holding the dredge in the digging position and long tailing flumes or short stackers off the stern for disposal of the barren materials. The California type (Fig. 3) uses box girder spuds projecting into the ground in a vertical position at the stern of the

Jan 1, 1969

By D. F. Hewett

ALTHOUGH most persons will agree that an individual or a nation can profit from the experience of other individuals or nations, there is always room for debate over the degree of similarity of their past and present conditions and of their future problems. Noting the increasing interest that Americans are showing in our mineral problems, I have felt that we could profit from reviews of the experiences in mineral exploitation acquired by the industrial nations of Europe. Whether we can learn much from Europe's experience in exploiting such minerals as petroleum may be debatable, but certainly, with a record of metal production extending back nearly 3000 years, Europe should hold much of value for America. A trip to Europe in 1926 permitted me to visit 28 mining districts, of which about half are now or have been in times past outstanding sources of several metals. The districts range from England to Greece and from Spain to Poland. To summarize briefly my impressions of these mining districts, as well as such reactions to the thought and life of Europe as so short a visit permits, I shall only venture the opinion that Americans can review with great profit the ideas and actions of Europeans, with regard not only to the production of metals but to many expressions of life. I believe that America has made and is making new contributions to the art of living, as well as to the arts of mining and metallurgy, but in so far as Europe is and has been a laboratory of economic, social and political experiments, the results she has attained deserve the thoughtful attention of America. I have come to believe that many of the problems that harass Europe lie in our path not far ahead. I have therefore hoped that a review of metal production in Europe in the light of its geologic, economic and political background may -serve to clear our vision with regard to our own metal production.

Jan 1, 1929

By A. N. Mitinsky

Discussion of the paper of A. N. MITINSKY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1697 to 1705. LAWFORD H. FRY, Burnham, Pa. (communication to the Secretary*). -The author assumes that the proportional limit and the elastic limit are coincident or very nearly so, and then further assumes that the stress corresponding to these two points is the least stress which if repeated will cause failure. The point is extremely interesting and it is to be regretted that the author did not quote experimental data to show the relation between the limit of repeated stress and the other properties of the material. The author's suggestion that a steel of poor quality may have a normal value for the yield point and tensile strength (see Fig. 2) and an abnormally low elastic limit, and that this will correspond to a low resistance to repeated stress, may account for a number of failures of axles in which the tensile tests show normal physical properties. If so and if a determination of the proportional limit would have eliminated the material before it was put into service, this determination will merit most earnest attention. It appears, however, that considerable further research is necessary before any definite conclusion as to the quality of a steel can be drawn from its proportional limit. Mr. Mitinsky's paper is extremely interesting and if it stimulates thought and work along the lines indicated, it may prove of considerable practical benefit. H. V. WILLE, Philadelphia, Pa.-The paper discusses the difference between the proportional limit, or elastic limit, and the yield point, and refers to the fact that much harm results from confusion of the terms yield point and elastic limit. Similar confusion has arisen in this country; the American-Society for Testing Materials does not even consider the elastic limit and proportional limit to be identical and recently adopted the following definitions:

Jan 12, 1915

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards&apos; work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By F. M. Simonds, E. Z. Burns

The Rawley property is located in the Kerber Creek mining-district, Saguache county, Colorado, at an elevation of 10,600 ft. (See sketch-map, Fig. 1.) Ore was found in this vicinity as early as 1880, and claims covering a large area were located and in many instances patented. The ores, however, being of comparatively low grade, and the nearest railway station, Villa Grove, being some 20 miles away, it is extremely doubtful whether any considerable amount of ore was ever handled at a profit. It is safe to say that several hundred thousand dollars were spent (a large part in building mills) previous to 1902-03. About that time a very capable promoter gathered together a group of these claims and interested some New York people, who had had no previous mining experience, in the purchase of these claims. Following the organization of a company, this promoter became General Manager. As often happens under such conditions, the first step was to erect a mill to treat 100 tons per day. It may not be fair to this enterprise to say that the failure which followed might have been foretold, simply on general principles, but this much is certain—the water supply fluctuates in the course of a season through a wide range and for a considerable portion of the year was inadequate to run this mill at capacity. Further, it is currently reported that some of the mill foundations were placed on ice. However true this statement may be, it is a fact that, when first inspected by us, many of the belts in the mill were held on&apos;their pulleys by means of idlers. A shut-down followed, with a material re-adjustment of interests, at which time we became consulting engineers for the company.

Jan 1, 1914

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By F. W. Jessen

The Mechanism of solution of salt and mixed halites of sodium and potassium is reviewed. The variation in the rate of salt removal under both laminar and turbulent flow conditions is discussed. Many changes are possible in the development of solution cavities whether used for production of salts or for storage of hydrocarbons. The parameters influencing the type and shape of cavity formed with single well or multiple well systems are examined and information presented regarding field application of techniques developed and the means of controlling overall configuration of solution cavities.

Jan 1, 1972

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique: the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi- normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By Charles T. Baroch, Charles J. Baroch

Nuclear energy probably has greater potentialities for changing the world&apos;s way of life than any other recent discovery. The atomic-bomb bursts over Hiroshima and Nagasaki suddenly changed the concepts of war. Peaceful uses of nuclear energy are advancing so rapidly that no study of economic trends is complete without giving them consideration. The minerals specialist, especially, must be aware of this new force in our lives, as minerals and metals are essential in harnessing the new force, and atomic energy itself is rapidly improving its competitive position in the energy field. Future historians may chronicle December 2, 1942, as the beginning of the Atomic Age. On that day Enrico Fermi and his co-workers at the University of Chicago produced and controlled the first self-sustaining nuclear chain reaction. Lie many inventions, the first application of nuclear energy was as a weapon of war. However, its potential usefulness in man&apos;s work and welfare far outweighs in economic importance its destructive use in war, unless its military effect would be considered so great and all-embracing that no major power will hereafter chance a world conflict. Recognition of this potential has generated a vast international effort to exploit the atom for peaceful beneficent purposes. Like its physical manifestation, the advent of nuclear energy has unleashed chain reactions that have pervaded the political, social, and economic environments of the world. The impact of nuclear developments in one of many fields is exemplified by the uranium mining industry. Uranium was discovered in 1789 and in the next century and a half it found only an insignificant use as a ceramic coloring agent; in fact, in the latter part of that period, it was a largely unsalable by-product of the radium and vanadium industries. Up to 1940 the total quantity of uranium metal produced was not more than a few grams, of doubtful purity. Thus the production of 12,400 pounds of pure

Jan 1, 1964

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920