Search Documents

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. [ ] A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By C. A. Heiland W. E. Pugh

The principle underlying the majority of magnetic intensity variometers is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechanical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection is given by tan = FIX, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment (see equation 1). The second effect is due to the change in the torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1934

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By R. Y. Williams

In the United States, fully 98 per cent. of the anthracite and bituminous coal tonnage obtained from underground operations is mined by the room-and-pillar system. Under this system, the total cost of the coal f. o. b. railroad cars contains as its greatest single item the money paid for "labor." Each labor dollar in an average bituminous mine may be subdivided into 85 c. paid for work done inby the gathering turnouts (including all work at the face), and 15 c. outby that point (including all work in and under the tipple). In an average anthracite mine, the corresponding figures are 70 c. and 30 c., the larger breaker force accounting mainly for the difference between these and the bituminous figures. The next largest single item after "labor" is usually "supplies and power;" and a division of this item inby and outby the gathering turnouts shows somewhat the same relative proportions as has been noted under the case of "labor". During the past 10 years, the chief advances made in the coal industry have been to obtain economies through complete mechanization covering that portion of the work which lies outby the gathering turnouts. These results have been accomplished by applying scientific principles to railroad yard layout, to cleaning and sizing machinery, to dumping facilities, to roller-bearing haulage equipment, and to heavy-rail, well-ballasted trackage. But these improvements, while gratifying in their resulting economies, apply only to 15 to 30 per cent. of the important cost items. Obviously, then, the big problem before the engineers of the coal industry today has to do with the methods of mining and the layout inby the gathering turnouts. Four years ago, Weston Dodson & Co., Inc., determined to have an exhaustive study made of the conditions which must be met in order to gain complete face mechanization, and in order that such a mining layout would be based on correct underlying principles. The result of that study, which was made by the writer, led to the adoption of a method of longwall mining wherein the roof is worked on the caving system and is supported as an overhang along the face by steel jacks.

Jan 1, 1928

By James Johnston

Synopsis.-A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably. complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the, processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at. 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their . high-grade ore,1 the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partial amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000.

Jan 1, 1914

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972

Jan 1, 1929

By E. C. Pechin

AT the suggestion of some members of the Institute, attention is called to the record of the working of Dunbar Furnace during the twelve months ending in January, 1874. During this period, with a product of over eleven thousand gross tons, not a single ton of

Jan 1, 1874

By M. P. Sidorova, D. A. Fridrikhsherg

The surface charge, electrokinetic potential and surface conductance were studied for silica, alumina and rutile as the functions of PH and concentration of 1-1 electrolyte solutions. The adsorption potentials of potential-determining and specifically adsorbed ions were calculated from isoelectric and zero charge points on the basis of Stern equation and thermodynamic description. From surface conductance and charge data the mean ionic mobilities in double layer were estimated. The results give some information about the real structure of oxide-electrolyte interface and gel-layer concept.

Jan 1, 1980

Jan 1, 1898

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

By Barbara A. Thompson

A previously reported high-resolution method for the location of boron-rich areas in metallurgical and biological specimens was been adapted for general use on a routine basis. The rnetlzod utilizes neutron activation and autoradiograpizy. Alpha-particles emitted by boron nuclei upon neutron capture are recorded on a photographic emulsion. The resulting a-particle tracks show the location of boron-rich areas. Experimental techniques, interferences, and limitations of the method are discussed in detail. The method is most useful where there is marked segregation of boron. In this type of sample, the segregation can be observed when the nominal boron concentration is as low as 0.0006 pct. THE positive identification and location of boron-rich areas in metals is frequently of great interest in metallurgical work. Unequivocal identification is often difficult to make by conventional metallo-graphic methods. Recently, a method has been described which accomplishes this objective by neutron activation and autoradiography.l-3 The method can be described briefly as follows. Upon neutron capture, a -particles are emitted by boron nuclei according to the following reaction: ,Blo + n - ,a4 + 3Li7 + 2.4 mev The energy is dissipated as kinetic energy of the products. By irradiating a boron-containing sample in contact with a photographic emulsion and subsequently developing this emulsion, a-particle tracks are obtained whose location corresponds to the location of boron-rich areas in the sample. Two factors combine to make the reaction extremely specific for boron. The first is the unusually high (755 barns) cross section of boron for thermal neutron capture. The second is the higher neutron energy required to produce (n, a ) reactions in essentially all other nuclei except lithium. These two factors make the method specific for boron by six to seven orders of magnitude when a predominantly thermal neutron source such as the Brookhaven reactor is used. The reported limit of detection of this method is of the order of 0.01 pct B., The present work was originally undertaken to determine whether this limit could be lowered by use of a thinner emulsion. However, initial experiments showed that in order to use the method at all, it was necessary to reestablish the optimum experimental conditions in terms of the available irradiation facilities. It is the purpose of this paper to describe these experimental conditions in detail, to discuss the factors influencing sensitivity, and to evaluate several techniques for increasing sensitivity. EXPERIMENTAL A) Preliminary Experiments—The first measure-ments were made using samples of crystal oriented silicon steel containing various concentrations of boron. In the later experiments, samples of various high-temperature alloys such as M-252, hcoloy 901, Nichrome V, and so forth, were used. Faraggi, et al.,2 reported that the lower limit of sensitivity in this type of sample was about 0.01 pct B using nuclear emulsions of 50- u thickness. but that it should be possible to extend this limit by the use of thinner emulsions. Accordingly, we first used Kodak Auto-radiographic Stripping Film (Permeable Base) which has an emulsion thickness of only 5 µ. This was mounted on the metallographic specimens according to the technique described by Boyd.4 The emulsion remained in contact with the metal surface throughout exposure and development. Since the emulsion is transparent after development, the autoradiograph and metal surface can be viewed simultaneously and any correlation between film blackening and structure of the metal can be made directly with no problems of realignment. Because the silicon steel is readily attacked by moisture alone, it was necessary to apply a protective coating to the metal surfaces before mounting the emulsion. The coating was made extremely thin in order to absorb as few a-particles as possible. Boyd4 and Gomberg5 have discussed various plastics used for this purpose; however, none was sufficiently impermeable to prevent chemical attack of the steel during the developing process. This attack resulted in the production of gross chemical artifacts in the emulsion. It was, therefore, necessary to use the method of Wolfsberg and John6 as follows. A very thin (approximately 1 µ) coating of Plexiglas II was applied by dipping the sample in a 2 pct solution of Plexiglas II in dichloroethylene. Then, because the emulsion will not adhere to Plexiglas 11, a thin coating of Parlodion was applied in a similar manner using 2 pct Parlodion in iso-amyl acetate. No protective coating was necessary with the high-tem-

Jan 1, 1961

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 8, 1950

COUNCIL OF SECTION DELEGATES E H Stevens, Chairman James W Halley, Vice-Chairman George J Donaldson, Secretary The Peoples Natural Gas Co 140 Stanwix St Pittsburgh 22, Pa EXECUTIVE COMMITTEE H R Wardwell, J G Evans, H R Bianco, Harry Campbell

Jan 1, 1955

Jan 1, 1935

Jan 1, 1923

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

Jan 1, 1894

Jan 1, 1904