Search Documents

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967

By Forbes Rickard

Gilpin County, the cradle of mining in Colorado and the Cornwall of North America, is too well known to need much introduction; get, for the benefit of those not familiar with the district, it may be well to premise that it comprises a tract of country of about 122 square miles, lying between the counties of Jefferson, Boulder and Clear Creek, and hounded on the west by the main range of the Colorado Rockies. It is located centrally in the State, 40 miles west from the city of Denver. During the 38 years since the first gold-discovery, Gilpin county has contributed about eighty million dollars in gold and silver to the world's supply of these metals. Many mining districts have had their rise and decline in half this time; but, very far from being exhausted, this mining district is still in the ascendant; its output is increasing (it was $3,600,000 for the year just closed), and it was never more prosperous nor productive than to-day. Taken generally, there does not exist anywhere in the world so great a number of permanent veins within so small an area as in this district. Gilpin is practically a " poor man's camp." Its veins, with few exceptions, outcrop at the surface. In the oarlier---days of the camp these outcrops were worked in many instances by sluice-mining; particularly is this the case with regard to the veins of the Russell gulch. Discoveries are still made in the heart of this district, and the productive area is every year extending its limits. The districts of Yankee Hill, Hawkeye and Pine Creek, which used to be isolated, are now part and portion of the one gold-field of Gilpin county. Within the last year sensationally rich gold-discoveries have

Jan 1, 1899

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

Jan 3, 1953

By A. H. Lee

Discussion of the paper of H. P. HOWLAND, printed in Bulletin No. 111, March, 1916, pp. 627 to 650. A. H. LEE, Buffalo, N. Y. (communication to the Secretary*). The statements and results recorded in Mr. Howland's paper can be accounted for by the use of coke with a low sulphur content (0.60 and under). This allows the furnaces to be run on a small volume of acid slag, which it is presumed was done in Mr. Howland's practice. H. A. Brassert has admitted that this was the largest factor in low fuel consumption in his practice. Where the coke contains from 1.00 to 1.25 per cent. of sulphur the situation is quite different and I doubt whether the results mentioned by Mr. Howland could be obtained under such circumstances. ` N. M. LANGDON, Mancelona, Mich. (communication to the Secretary + ).-Gruner's ideal working (which is but a statement of the law first enunciated by Bell) as given in Gordon's Translation of Studies of Blast Furnace Phenomena, "supposes that the reduction of the oxide of iron is effected by the CO only, without intervention of solid carbon." This ideal, if reached, would mean theoretically perfect or 100 per cent. efficiency of reduction. The workings of the large number of furnaces as given in Bell's and Gruner's great works do not show that this standard of perfection ever was reached. This problem has been worked out by the writer for a number of furnaces, and his results, as well as those given by others, all show a failure to reach perfection. Some furnaces, however, approach nearer to perfection than others. The "ideal" as given by Gruner was not stated as a solved problem in blast-furnace practice, but as an ideal to the attainment of which furnace managers should strive. A study of the factors involved from every angle is interesting and instructive and the paper on this subject contributed by H. P. Howland is no exception to the rule. This article is fairly open to criticism, not because of the unique method of presenting the subject, but for the reason that, as the writer conceives, erroneous assumptions are taken which lead naturally to incorrect conclusions.

Jan 7, 1916

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By James K. Richardson

Today, the enigma of the "missing man" in the metal mining industry equals, and frequently surpasses in objective importance, the problems of ore development, drilling, sampling, pumping, milling techniques, geophysical prospecting, or any one of a hundred highly technical subjects. Unfortunately, as engineers, we have confined our attentions, in the main, to the scientific phases of mineral technology, relegating our man power problems to the background. But what good has all our scientific study and preparation been if we can't get the ore mined, milled, or smelted? What has happened to our labor supply? Where is the good old miner who could timber, drill a round, lay track, or do any job underground?

Jan 1, 1949

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Paul M. Tyler

DOES mining pay? Inasmuch as the whining of minerals from Nature is one of the world's principal sources of new wealth, this question is of general economic interest but it is obviously of even more vital concern to investors and those engaged in mining. In a previous article on "Wage Costs in the Mineral Industries,' published in the November issue, I attempted to show that wages paid workers on the job accounted for, roughly, 50 per cent of the mine dollar. Salaries normally range over 5 per cent - lower for large metal mines but higher in stone quarries and minor nonmetallic min. in, industries. Purchases of supplies, materials. fuel, and power generally aggregate within the range of 15 to 25 per cent of total receipts, with the average well under 20 per cent. The total of all such specified expenditures which may he loosely described as

Jan 1, 1934

By A. U. Seybolt

A FEW copper-zinc-base alloys meet die-casting requirements reason- ably well, although improvements are desired. Aluminum bronzes, high-tinbronzes and some copper-nickel-zinc alloys can be die-cast, accordingto Herb,1 but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. TABLE 1. Commercial Die-casting Brasses a Constituent Yellow Brass Low-silicon High-siliconb Brass Brass Nickel Silver Composition, Per Cent Cu 57-59 63-65 80 -81.5 42.0 Zn 40-42 33-35 13.5-16.0 41.0 Sn 0.5-1.5 Si 0.75-1.25 3.75-4.25 Pb 1.0 Ni 16.0 Properties Tensile, lb. per sq. in.. 55,000-60,000 65,000-70,000 85,000-95,000 85,000-95,000 Yield, lb. per sq. in.d.. 30,000-35,000 35,000-40,000 65,000-70,000 65,000-72,000 Elong., per cent in 2 in . 15-20 20-30 8-12 10-20 Brinell hardness 120-130 120-130 160-180 160 Specific gravity 8.47 8.50 8.15 8.45 Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy, 3,4 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. c Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb' as 1650° F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600° F., and of the nickel silver as 1675° F. d Criterion not stated.

Jan 1, 1939

By George M. Fowler, Joseph P. Lyden

PaGE Scope of this Report.................................................... 206 Production of Tri-State District.......................................... 207 Historical Sketch....................................................... 207 Location and Topography............................................... 211 Geology............................................................... 212 The Tri-State District.............................................. 214 Stratigraphy........................................................... 217 General Geological Section in Tri-State Region....................... 217 Stratigraphic Section of Mineralized part of Boone Formation........... 218 Stratigraphic Section Bird Dog Well.................................. 219 Metamorphism........................................................ 220 Structure............................................................. 225 Regional.......................................................... 225 Due to Metamorphism.............................................. 229 Ore Deposits.......................................................... 231 Types............................................................ 232 Hard-ground Deposits.......................................... 232 Brecciated................................................. 232 Stratified............................................ 232 Sheet Ground............................................. 232 In Dolomite............................................... 233 In Shale.................................................. 233 Soft-ground Deposits.......................................... 233 In the District as a Whole....................................... 233 Ore Minerah and Analysis......................................... 233 Paragenesis....................................................... 234 Conclusions........................................................... 236 Structure.......................................................... 236 Genesis of the Ore.................................................. 237 Future of the District............................................... 239 Acknowledgments..................................................... 239 Discussion............................................................ 239 Scope of This Report The Tri-State district. as outlined in this paper. refers to the entire mineralized area in sout'hwestern Missouri. southeastern Kansas and

Jan 1, 1932

By H. H. Stoek, G. W. Harries

The term " Anthracite Coal-Field " is generally used to refer to a comparatively small territory lying in the eastern-central part of Pennsylvania. This territory includes about 3,300 sq. miles of area, located chiefly in five counties in which anthracite-mining is the dominant industry. Although an area of 3,300 sq. miles is embraced in the region, less than one-fifth of this area, or only 484 sq. miles, is underlain by workable coal-seams. Moreover, this prorluctive portion is not a continuous area, but consists of a number of detached basins. These are known as the Northern, containing 176 sq. miles; Eastern-Middle, containing 133 sq. miles; Southern, containing 181 sq. miles; and western-Middle,containing 194 sq. miles. From the standpoint of business and trade, the region is divided into three districts, known as (1) the Wyoming, which includes the Northern field and the small Bernice basin; (2) the Lehigh region, which includes all of the Eastern Middle field and that part of the Southern field east of Tamaqua; and (3) the Schuylkill region, which includes the WesL ern-Middle field and that part of the Southern field west of Tamaqua. The relative commercial importance of these districts at the present time is shown by the coal-shipments as given in the following table :

Jan 1, 1904

By Howard Evans

Moderate but substantive gains were recorded in 1972 in the minerals processing industry. In the area of mill design, a number of large plants under construction during the past two to three years were tuned up and went into production. The application of operating controls has also made some significant strides. Progress here has been made in the areas of on-stream particle size analysis, on-stream x-ray analysis, slurry transportation, tripper control, flotation reagent control and digital control of grinding circuits. The major contributions to improved equipment are coming from smaller specialized equipment makers.

Jan 2, 1973

By W. E. D. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail- way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews. According to the U. S. Geological Survey, commercial firms photographed 16,291 square miles during 1935, while the Government compiled from aerial photographs by the Geological Survey in the United States 85,544 square miles. It was found that information could be determined in a fraction of the time required by surface methods. However, sounding a word of caution, a Commonwealth of Australia government report on aerial survey operations had this to say: It is necessary to repeat ad nauseam that aerial photographic survey is in no sense a substitute for geological investigation, though it is a very valuable adjunct thereto, and greatly facilitates and accelerates geological mapping. There are many details

Jan 1, 1937

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By W. C. Clark, J. B. Schloen

Two papers have been written, previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,Z published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 ox. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidiae-roasted at 700' F. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent HzSOa), filtered and charged directly to the dor6 furnace for refining to dore metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1944

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975