Search Documents

By M. N. Short, I. A. Ettlinger

M. N. Short,? Washington, D. C., and I. A. Ettlinger, New York', N. Y. (New York Meeting. February, 1926) The Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a, confused series of mountain ranges of moderate height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County. The Magma copper mine (Fig. 1) is the only producer in the district. Although discovered in 1875, its production has been important only

Jan 1, 1927

By J. S. Ll. Leach, M. B. Bever

THE system copper-nickel exhibits complete solid and liquid miscibility1 The thermodynamic properties of such a system would not be expected to deviate greatly from ideality. Although the evidence is conflicting, anomalies in the composition dependence of various physical properties of solid copper-nickel alloys suggest that mixing may not be ideal.' From measurements of the Hall coefficient it has been concluded that clustering occurs in these alloys. ' Considerations involving the phase diagram of the ternary system copper-nickel-chromium have led Mei-jering3 to predict a positive heat of formation for solid copper-nickel alloys. An electrochemical investigation of the activity of nickel in copper-nickel alloys showed unexpectedly large positive deviations from ideality.4 wagner5 has proposed that if the entropy can be considered ideal, these measurements would yield the following equation for the heat of mixing at 700°C H" = 3380 x,vl (l-xVi) cal per g atom [I1 The heat of formation at 722°C of solid copper-nickel alloys of the equiatomic composition has been measured in a reaction calorimeter as 540 cal per g atom. This note reports calorimetric measurements of the heat effects on dissolution of some copper-nickel ndon: in tin. These measurements were preliminary to a larger investigation, which was later discontinued. From them the heats of formation of the alloys can be calculated, if certain assumptions are

Jan 1, 1960

By B. S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954 2.' In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger pieces of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct —325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine. The first mill to use screened ore to grind the ore (1949) was Lake Shore Mines, Kirkland Lake, Ont. Pebbles were screened from the jaw crusher discharge and used in 5x16-ft tube mills which had been converted to 6 ft 8 in. by 16-ft grate discharge pebble mills. The same general practice was adopted the following year by the Wright-Har-greaves Mine in Kirkland Lake. Shortly after that the Neptune Mines in Nicaragua started correspondence with the writer concerning the possibility of using screened ore for grinding in their plant. They first ran some plant-scale tests which confirmed the Lake Shore findings, with the ultimate result that their plant was successfully converted in 1956 to an autogenous grinding plant. In 1957-1958 the writer was successful in converting the grinding plant of Renabie Mines in northern Ontario to autogenous grinding. In all these plants the existing grinding equipment was converted, usually by expanding the diameter of the shell to make the change from steel grinding to ore pebble grinding mills. In all the above plants primary grinding was done in either small rod mills or ball mills. These mills first reduced the pebble mill feed to about 6 mesh. The final grinding in the pebble mills varied from 75 pct —200 mesh to 92 pct —325 mesh. At Lake Shore three stages of pebble milling were used, with a different size pebble in each stage. In other parts of the world interest was being shown in this form of grinding, and in March 1952 the writer had some correspondence with the mill staff at Outokumpu in Finland, with regard to the pebble system used at Lake Shore. At Stockholm in 1957 the account of the crushing and grinding system at Outokumpu was presented in a paper by H. Tanner and T. Heikkinen.V his is the only ore grinding plant that does not use grate discharges on its pebble mills; trunnion discharges equipped with heavy reverse spirals retain the pebble load. The first new mill designed to use screened ore as a grinding medium was the Bicroft mill at Bancroft, Ont., which began operation in the fall of 1956. In 1957 this plant was followed by similar installations at Faraday Mines, also in the Bancroft area, and the North Rankin Nickel Mines in the North West Territories. In 1958 the Dyno Mill at Bancroft was converted, using the same type of grinding. Since all these plants, designed by Kilborn Engineering (1954) Ltd., were originally planned as pebble grinding mills, they were able to take full advantage of the latest design and technique. They are neat in appearance and very efficient and easy to operate. Effect of Ore Hardness: It is often commented that this type of autogenous grinding applies only to hard siliceous ores. Experience has shown that this is not so. In the past ten years the author has had an opportunity to test more than a dozen ores, several of which were quite soft. One of these was shale. The softer ores actually make better looking pebbles than the hard ores. These soft ores produced no particles in the intermediate size range which could not be ground by the largest pebbles in the mill charge. Slabby ores, such as shales, make a suitable pebble for the —6 mesh grinding. It is not generally recognized that for fine grinding a spherical medium is not essential or more efficient. Another frequent objection to pebble grinding is the belief held by some operators that there is too much variation in the hardness of their particular ore to make it acceptable as a source of pebble media. Experience has also shown that this is not a serious problem at all. The variation in pebble load due to changes in the ore hardness is nothing like as great as most people would expect, and the method used for feeding the ore and controlling the the load in the mills is more than sufficient to take care of daily variations in ore hardness. This point

Jan 1, 1960

By CHARLES M. A. STINE

IN fighting a war the all-absorbing intent is to win. There is little time to analyze the rush of events or to appraise their consequences beyond the war's end. The united objective is, rightly, success for our arms. Yet under the pressures of a great war there may be compressed scientific, economic and social developments that might have taken many decades to achieve under less urgent conditions. Their effects on our lives and all civilization may be more wide-reaching and lasting than any military conquest. They constitute one of the must imperative incentives to victory. No American, least of all any scientist worthy the name, conceivably could endorse war as a justifiable means to progress. The destruction of life and property wrought by the present war far exceeds the havocs of a century's earthquakes. Most of mankind is burning itself on an altar of paganism. Nonetheless, one fact is inescapable Despite the recurrent malady of war history's overall course is forward. Mankind has the habit of rising phoenix-like from its own ashes to attain greater heights. Progress is immortal.

Jan 1, 1942

By John D. Sullivan

ALUMINUM and magnesium plants in the United States underwent enormous wartime expansion which made many wonder if ghost plants would result when industry swung back to a peacetime basis. Production capacity of primary aluminum ingots was stepped up from 150,000 tons annually to about 1,150,000 tons; magnesium production increased from 2500 tons in 1936 to nearly 200,000 in 1943, with a production capacity of some 300,000 tons. Not only was primary metal production enlarged but also the capacity of prime fabrications such as castings, forgings, extrusions, and sheets was correspondingly increased. In mid-December it was estimated that production of primary aluminum ingots in the United States in 1946 will be about 410,000 tons while consumption will be about 500,000, close to half of the wartime consumption. The 1946 estimated consumption of secondary aluminum is 200,000 tons. The critical shortage of soda ash is hindering production of primary metal, and the outlook for an early relief of this shortage is dark.

Jan 1, 1947

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0' (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,' Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (' transformation is suppressed; but ordering takes place (i.e., 0 -0'). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0' phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b' within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

By D. J. Pye

Certain high molecular weight synthetic polymers in very dilute solutions decrease water mobility in porous media 5 to 20 times more than would be expected from the solution viscosity. This indicates that increasing water viscosity to reduce adverse mobility ratios in water floods is economically feasible in many situations. Laboratory results are consistent with accepted theory with respect to improved areal sweep, permeability distribution and displacement efficiencies as would be predicted from the solution mobility measured in the core. The laboratory results have been confirmed by field pilot floods which recovered 80 per cent and 100 per cent more oil than comparative water-flood pilots in fields containing 16 cp and 130 cp oil respectively. Economic analyses based on pilot data indicate the method to be profitable. INTRODUCTION The desirability of improving the water-oil mobility ratio in waterflood-ing operations has long been appreciated, especially for high viscosity crudes. Methods of reducing the oil viscosity by application of heat, gas resaturation and miscible drives have met with some success. Conversely, it has been generally conceded that increasing the water viscosity would also be effective, but the amount of thickening agent required to effect an appreciable increase in viscosity is discouragingly high. The use of such materials as glycerin, sugar, or glycols is completely out of the question economically, so that considerable attention has been given to the use of the much more efficient synthetic water-soluble polymers as viscosity improvers; but even these materials are not economically attractive. If increased water viscosity could be economically realized, marked improvements in areal sweep efficiency, as discussed by Caudle and Wittel and others, would be realized in field operations. Similarly, the improved mobility ratio would bring about increased recoveries by correcting permeability distribution problems as discussed by Stiles2 and Dykstra and Parsons,' and improvements in displacement efficiency would be obtained as recognized by Buckley and Leverett4 and Welge.5 LABORATORY STUDIES THE RESISTANCE EFFECT In the course of research to develop a more efficient water-soluble polymer viscosity builder, we discovered that a very few types of water-soluble polymers exhibited a most unusual and very interesting property not previously observed. Among the earliest materials showing such activity were polymers containing acry-lamide. Fig. 1 shows a typical plot of the solution viscosity vs concentration for one of these polymer solutions as determined in an Ostwald viscometer. As usual, such a plot is an approximate straight line on semi-logarithmic paper. Now, an inspection of Darcy's law, shows that a viscosity value can also be determined in a formation sample if the pressure, flow rate and permeability are known. If the core permeability is previously determined with wa- ter or brine, then the viscosity of another aqueous fluid may be determined from the equation. The viscosities so determined for glycerin (glycol or polyvinyl alcohol solutions, for example) agree with the viscometer determinations. However, in the case of the water-soluble polymer solutions in which we are interested, the viscosities measured in the formation sample depart very markedly from the viscometer values. A typical relationship for a polymer solution is also shown in Fig. 1. This unusual departure from the expected response is referred to as a resistance property of the polymer and is quantified as "resistance factor". Since the resistance factor R can best be determined in a core under study, the term has been defined on the basis of the ratio of the brine mobility to the polymer solution mobility at residual oil saturation so that:

Jan 1, 1965

By Albert D. Brokaw

THE accompanying chart was devised to provide a rapid and simple method of correcting for temperature and compressibility (deviation from Boyle's law) of gas under relatively high pressures and temperatures, such as are encountered in many deep reservoirs. The chart was prepared by interpolating for the desired values in the experimental data of Burke and Keyes1 and Kvalnes and Gaddy2 on the compressibility of methane, after adjusting their results from 0°C. to 60°F. and combining the correction factors for compressibility and temperature into a single multiplier, which, applied to the product of pressure and reservoir volume, gives at once the volume at one atmosphere (14.7 lb. per sq. in. abs.) and 60°F. The relationship 0f this multiplier to the compressibility factor Z, as used in most discussions, is simply: [Multiplier = 460° + 60°ZT –] where Z is the compressibility factor and T the absolute temperature (Rankine). Fahrenheit temperatures are shown on the vertical axis and pressures in pounds per square inch absolute on the horizontal axis. Correction factors or multipliers at intervals of 0.05 from 0.55 to 1.40 have been plotted on the chart and are calculated t0 give volume of gas at one atmosphere pressure (14.7 lb.) and 60°F. The operation is as follows: The reservoir volume, times the number of atmospheres pressure, times the multiplier, gives the volume of gas measured at one atmosphere (14.7 lb. per sq. in.) and 60°F. For example, a reservoir is estimated to have a volume of 10,000,000 cu. ft., bottom-hole pressure is 2940 lb. per sq. in. and temperature is 184°F To make the correction for methane, follow the 184° line horizontally to the 2940-lb. pressure line. The intersection lies between the 0.85 and 0.90 correction lines, and by interpolation we may estimate the multiplier at 0.863. The computation is simply: [ ] Using the chart for methane prepared by Prof. G. G. Brown3 and his associates, the multiplier is found to be 0.867. Details 0f computation are as follows: Correction factor to apply to PV to correct for deviation from Boyle's law and adjust to measurement basis of 60°F.: [ ]

Jan 1, 1941

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sillimanite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized.

Jan 1, 1950

Prof. Henry S. Jacoby, Cornell University,Ithaca, N.Y. (communication to the Secretary): When a simple beam supports any given load, the lower fibers me in tension while the upper fibers are in compression, and if its cross-section is rectangular the neutral surface, where the stresses pass through zero from tension to compression, is at mid-depth, provided the elastic limit is not exceeded. In addition to the longitudinal stresses, there are horizontal shearing-stresses between the fibers which have their maximum value in the neutral surface, and which equal zero at the upper and lower surfaces, while there are also vertical shearing-stresses. Let another beam of the same dimensions be placed on top of this one, and the load be doubled, it then produces stresses in each beam of the same character, magnitude and distribution as in the preceding case, provided there be no friction between the adjacent surfaces of the beams. Next let these two beams be so firmly united that there will be no motion between them when the same load is again applied. All the fibers in the upper beam are now in compression, and those in the lower beam in tension, while the maximum stresses in the outer fibers are only one-half as large as before. The strength of the combined beams is therefore doubled. If, however, some motion occurs between the beams, then the stresses in some of the lower fibers of the upper beam pass from compression to tension, and those in some of the upper fibers of the lower beam from tension to compression, while the stresses in the outer fibers have a magnitude between the two values previously stated. These fundamental facts relating to the flexure of beams indicate the necessity of carefully designing the keys or brace-

Jan 1, 1898

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By Edward B. Cook

INTRODUCTION. THE installation of the Gayley Dry-Air process appealed specially to the management of the Warwick Iron & Steel Co., for the. reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to. make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, on a much lower fuel-consumption, while, at the same time, the summer months were marked by ? messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient capacity to treat 70,000 cu. ft. of air per min., an amount

Nov 1, 1908

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By AIME AIME

MEMBERS of the Engineering Education Committee held two meetings at Joplin preliminary to the opening of the main meeting there. The first was held on Sunday afternoon. It was attended by all who had arrived early enough and as among the dozen or' fifteen who were present the heads of a half dozen schools of mines were included it was a representative gathering. C: H. Fulton, chairman of the Committee presided and T. T. Read acted as secretary of the meeting. The chair., man reminded those present that last year there had been some discussion as to the advisability of the proposal, made by Edward Steidle, that a, separate society, devoted to education in the mineral industry, he organized. Many .people had felt that there are already so many societies in existence to demand one's time and attention, that it would be a mistake to add to their number and the counter suggestion had been made that the work of this committee could be so reorganized as to meet all the needs that a separate society could fill. He therefore presented for discussion these four' questions: (1) Shall a subcommittee .be appointed to study, and report in February, 1932, the possibility of the reorganization of the work of the Engineering Education Committee into the equivalent of an' Institute division; (2) if the work is so reorganized what shall be the relation of the work of the Committee (division) to the work of the-Society for the Promotion of Engineering Education; (3.): what are the, cardinal objectives of education for the mineral industry; and (4) what should be done as regards the movement in some institutions to plan their work-in the light of that being done in other institutions, for example, in geophysics?

Jan 1, 1931

By AIME AIME

TRADITIONALLY, the Annual New York Meetings of the A.I.M.E. cover four days, but the program is growing on each end as well as in the middle, and this year it lasted from 3 p. m., Sunday, Feb. 16, when the Education Division got under way, to 8:40 p. m., Friday the 21st, when a trainload of electrical inspectors, pro tern, got back fro111 the General Electric plant at Schenectady. The meeting has ceased to be a mere three- ring circus: on Wednesday afternoon eight sessions were being held simultaneously in the Engineering Societies Building, if one includes the Woman's Auxiliary, and according to frequent testimony one should include the W. A. as one of the most important units in Institute affairs.

Jan 1, 1936

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited ." Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By Davenport, Edmund S.

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned t for long periods in lamps. In these cases it was noted that the grain bound aries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits arc actually small voids between the grains. The purpose of this paper is to, present the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting is frequently associated with poor performance of filaments in lamps.

Jan 1, 1927

The sudden and untimely death of Dr. Charles R. Van Hise, late&apos; president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people&apos;s university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise&apos;s contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise&apos;s death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920