Search Documents

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Herman Pessoa Lima Júnior, José Brant de Campos, Rodrigo Felix de Araujo Cardoso, Paulo Renato Barbosa Marinho, Rauni Coelho da Costa

A técnica de SAXS é um método analítico que possibilita a determinação de diversas propriedades em nanomateriais, onde o colimador é a parte mais importante da óptica deste tipo de equipamento, sendo sua fabricação um desafio. Software de CAD 3D e 2D foram utilizados no desenvolvimento e fabricação de um bloco de colimação e testes comparativos foram realizados com fontes de raios X. Os testes mostraram que a geometria do feixe colimado é condizente com os modelos geométricos previamente resolvidos.

Oct 1, 2019

By Mühlböck Marlene

Increasingly stringent global environmental regulations are forcing steel producers to continually improve the efficiency of sinter waste gas treatment. With the Selective Waste Gas Recirculation (SWGR) system from Primetals Technologies, lower production costs can be achieved and the size of downstream waste gas cleaning units can be reduced for investment savings. SWGR features the extraction and reuse of hot sinter off gas from selected wind boxes along the sinter strand, which contributes to improved energy efficiency and off gas treatment in the sintering process. With the next generation of SWGR, Primetals Technologies can provide an energy optimized, emission optimized and environmentally friendly solution that meet customer requirements and country specific regulations. This paper demonstrates the latest developments in selective waste gas recirculation, especially results from pot grate tests and comparison from lab to real plant data. Furthermore theoretical finding and mathematical modelling is presented.

Aug 16, 2017

By Alcides José de Lucena Silva

O objetivo deste trabalho é demonstrar o desenvolvimento da compensação de sopro no Alto-Forno 3 da CSN durante as manobras dos regeneradores para o ciclo de sopro com o incremento da vazão do ar soprado vindo do moto-soprador. Para a realização deste trabalho utilizou-se a metodologia DMAIC. Na apresentação do resultado final serão demonstrados valores alcançados em torno de 60% de redução da pressão da base do alto-forno com o desenvolvimento e por consequência, um aumento de sua produtividade.

Aug 1, 2018

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Alessandro Martinis

The performance requirements for modern steelmaking facilities are ever more stringent, as customers and markets are continuously pushing for technologies which allow having high quality steel produced in an economic and sustainable way. In the details, this paper has the aim to present the excellent results obtained by integrated steel plant where an EAF is fed with high quality hot ENERGIRON DRI. The recent technology developments, combined with the affirmed basic process design, contributed to further maximize the energy of the DRI, reaching the EAF at temperatures above 600°C with a carbon content up to 3.5%, as confirmed by plant data. These improved input material characteristics resulted in reduced electrical energy consumption and increased liquid steel production.

Aug 16, 2017

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Charles Sóstenes Assunção

A mathematical model of heat transfer and solidification for a continuous casting of round billets was developed. The water flux density of the secondary cooling zone was experimentally measured, using an apparatus in industrial scale with two types of nozzles, flat jet and full cone jet. The profiles of water distribution were applied on the mathematical model. The results showed that the water distribution is not uniform in both longitudinal and angular directions owing to the unevenness of the spray and to the curvature effect of the round billet. This non-uniformity causes important variation of the heat transfer coefficients and superficial temperature of the billet, especially in the first cooling zones, where the temperature is higher. The mathematical model was used to simulate a change of nozzle type in the first cooling zone. The results showed that the heat flux and superficial temperature variations were reduced with a full cone jet nozzle in comparison with the flat jet nozzles.

Aug 16, 2017

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By José Dimas de Arruda

O conhecimento do campo de fluxo dentro do molde de lingotamento contínuo pode oferecer uma oportunidade de se melhorar a limpidez interna do produto. Modelagem física, aplicação da técnica PIV juntamente com a modelagem matemática via Ansys Fluent foram empregadas para avaliar a distribuição de velocidades na região de interface metal escória num molde de lingotamento de placas. Os resultados foram analisados com base em critérios de estabilidade da interface metal – escória disponíveis na literatura e ressaltam o papel do empuxo e tensão interfacial.

Aug 16, 2017

By Caroline Antunes Corrêa

Filmes híbridos estão sendo utilizados como revestimentos de substratos metálicos para proteção contra corrosão. Este trabalho tem como objetivo verificar o comportamento corrosivo de filmes híbridos com diferentes concentrações de polietilenoglicol (PEG) sobre folhas de flandres pela técnica de varredura por eletrodo vibratório (SVET). Os resultados demonstraram que o aumento da concentração de polietilenoglicol ocasionou a formação de fissuras e delaminação do filme híbrido. As análises por SVET demonstraram a possibilidade de analisar a corrosão localizada em regiões com defeitos no filme e no substrato metálico.

Aug 16, 2017

By Loyslene Rabelo Fernandes

Esse trabalho experimental apresenta os resultados preliminares da lixiviação de placas de circuito eletrônico de microcomputadores sucatados visando a extração de cobre, além da recuperação daquelas espécies através de precipitação por neutralização do licor de lixiviação. As placas foram desmontadas, fragmentadas em pedaços menores, onde passaram por uma incineração no forno mufla, moídas por moagem manual, onde depois sofreram ataque com ácido clorídrico e ácido sulfúrico. Também houve o processo de eletrodeposição com as laminas de cobre encontradas na moagem manual, onde apresentou 14% de cobre depositado.

Oct 30, 2017

By Paula Maria Gomes Cunha Leão

Um modelo matemático tridimensional, via software Fluent 14.0, de modo a descrever o fluxo, em regime transiente e isotérmico dos fluidos escória e nitrogênio, foi utilizado para avaliar o comportamento de slag splashing em um convertedor a oxigênio com o propósito de reparar as regiões desgastadas do revestimento de trabalho deste reator. Para um dado padrão de sopro foi investigou-se o efeito de parâmetros tais como temperatura, densidade, viscosidade e tensão interfacial. Os resultados são comparados com dados de projeção disponíveis na literatura.

Aug 16, 2017

By Ana Clara Petrucelli

O reator EOF foi desenvolvido no Brasil nos anos 1980 com características únicas. O pré aquecedor de sucata e a distribuição dos pontos de injeção de gases oxidantes e combustíveis conferem estas características. O objetivo deste trabalho é reproduzir o comportamento do banho metálico de um EOF de 45 t comparando seus três pontos de injeção: lanças supersônicas, lanças atmosféricas e ventaneiras. A lanças supersônicas e ventaneiras promoveram uma grande agitação do banho quando comparado com os injetores atmosféricos uma grande oportunidade de melhoria.

Jul 29, 2018

By Géssica Padilha de Souza

Nos dias atuais, tem-se uma busca incessante por materiais que atendam às solicitações de trabalho exigidas, mas que possuam um baixo custo de fabricação. Diante disso, esse trabalho tem por objetivo o endurecimento do aço AISI 1140, que foi normalizado, temperado com resfriamento em salmoura e seguido de revenimento, com posterior caracterização metalográfica e ensaio de dureza HRC. Através desses tratamentos, foi possível aumentar significativamente a dureza do aço em questão, além das modificações nas fases da microestrutura e consequentemente, de suas propriedades.

Aug 16, 2017