Search Documents

By Afrânio Márcio Costa

Placas lingotadas continuamente, não obstante atendam a requisitos como composição química, conteúdo de inclusões, aspectos macro e micrográficos, podem ser desclassificadas por falta de conformidade dimensional. Contrações térmicas, de solidificação e de transformações de fases são partes intrínsecas do processo e são afetadas por alterações na taxa de extração de energia da placa durante o processo. Este conjunto de contrações determina o Fator de Contração de operação, o qual é utilizado para determinar as dimensões do molde que irão resultar na largura especificada, onde o presente estudo determinará o fator de contração dos aços peritéticos. As variáveis identificadas que influenciam no fluxo de calor primário foram: frequência de oscilação, superaquecimento, velocidade de lingotamento e viscosidade do pó fluxante. Identificou-se que o resfriamento secundário e a conicidade utilizado no molde, também são critérios determinantes para obtenção de larguras especificadas. Assim sendo, uma equação de regressão foi desenvolvida para o Fator de Contração.

Aug 17, 2017

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

By CIM Environmental, Social Responsibility Society

Within the mining industry, the pathway from exploration, to planning, construction, operation and closure has become more complex over the last few decades. The current financial, environmental and social influences present the mining industry with unprecedented challenges and opportunities. In addition, international environmental and social reporting standards and codes are becoming increasingly robust. The reporting requirements provide an added impetus for issuers to effectively manage environmental and social impacts and risks. Reporting requirements also provide the opportunity to be transparent. The intended audience for these Environmental, Social and Governance (ESG) Guidelines for Mineral Resource and Mineral Reserve Estimation includes practitioners, industry participants at all levels of skill and experience, corporate management and board members, government agencies, academic institutions and interested parties. For practitioners, this document provides underlying key principles of environmental, social and governance practices. The ESG Guidelines provide guidance for those using environmental, social, governmental and governance information when preparing and implementing mineral exploration programs and contributing to the preparation of mineral resource and mineral reserve estimates for mineral properties that are either at the study stage (i.e., scoping / preliminary economic assessment, pre-feasibility, or feasibility studies) or in operation. The guidelines can also be used to help mineral resource and mining companies apply good practice to manage their environmental and social risks and opportunities. Companies can identify and retain appropriate professionals to prepare environmental and social materials to support company studies. The guidelines are also a resource for companies developing effective environmental and social management strategies at any project stage. This document is not intended to be prescriptive and is not intended to provide exhaustive guidance on what to consider in terms of environmental, social, legal and governmental modifying factors in the preparation of MRMR estimates. Rather, it is intended as general guidance to assist companies and practitioners in considering and applying these modifying factors for MRMR estimates. This document is also not intended to guide environmental and social impact assessment (ESIA); however, the measures needed to manage impacts help inform the constraints and costs for defining mineral resources and mineral reserves and inform the costs and schedules of mineral project studies. All documentation of MRMR estimates made by an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time (Canadian Securities Administrators, 2016a and 2016b). Disclosure is not addressed in these ESG Guidelines. Determination of what to include in disclosures is defined in the applicable Securities’ legal frameworks. Appendix A presents a summary table showing the linkage of the principles and topics in these ESG Guidelines to the potential effects on project costs, schedules, government permits and approvals, social licence to operate and financing.

Sep 8, 2023

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By Bill Tucker, Mike Black

"PROJECT OVERVIEW Crossrail, Europe’s largest construction project, will increase London’s transportation capacity by 10% when it opens in 2018. The Crossrail scheme is a combination of surface and underground railway that stretches 118km east-west through central London from Reading, Berkshire and Heathrow airport in the west to Shenfield, Essex and Abbey Wood in the London Boroughs of Greenwich and Bexley in the east. Crossrail will serve 40 stations, ten of which are new, and bring 1.5 million people within 45 minutes commuting distance of London’s key central business districts. 21km of the Crossrail route comprises twin-tunnels beneath the heart of central London. It is the central section of the route, and the challenges that had to be overcome to construct its tunnels under the historic capital that forms the subject of this paper. The route of the Crossrail tunnels can be seen in Figure 1. These tunnels weave their way through the city’s underground landscape, linking eight new underground stations which connect to the existing London Underground network, providing interchanges with nine existing lines as well as the National Rail and Docklands Light Railway networks.Crossrail began construction of enabling works in May 2009 and launched the first of eight tunnel boring machines (TBMs) in May 2012. 42km of major tunneling work was completed in May 2015, and included 11km of sprayed concrete lined tunnels at the five mined stations (Bond Street, Tottenham Court Road, Farringdon, Liverpool Street and Whitechapel) in addition to the bored tunnel sections. The remaining three sub-surface stations at Paddington, Canary Wharf and Woolwich were constructed as large open boxes prior to the TBMs passing through. Crossrail, Ltd. is a special purpose company formed by the project’s joint sponsors, Transport for London and the Department for Transport, to manage design, construction and commissioning of the project. In 2009, Crossrail engaged Bechtel Ltd. as its delivery partner and a joint venture, Transcend (comprised of CH2M, AECOM and the Nichols Group), as its programme partner. The project is being managed by an integrated programme management team which is staffed by Crossrail and its partners. The railway, when opened, will be operated by Rail for London. With tunneling completed in accordance with the project’s master control schedule, the new railway is scheduled to commence dynamic testing in late 2017, with a phased opening of the tunneled sections and stations through Central London in 2018."

Jan 1, 2016

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By R. C. FLEMING

MINING rock asphalt for use as a paving material is an industry which has grown with the spread of the good roads movement. "Mineral Industry During 1930" reports asphaltic pavements constructed, including maintenance and repair but excluding pavement constructed with road-oil, cut-back or emulsified asphalt, as grown from 23 million square yards in 1911 to a high of 144 million in 1927. In 1930 the same source reports 106 million square yards of such paving laid and, in that year, 664,871 tons of native rock asphalt were so utilized. Many states contain rock asphalt deposits of greater or less importance but in only a few places are the de¬posits being mined commercially. In the year cited Ken¬tucky produced 305,024 tons of bituminous sandstone, Texas 270,138 tons, mostly bituminous limestone, while Alabama, Oklahoma, California and Utah produced 89,709 tons of bituminous rock for road construction. In addition Utah produced 37,906 tons of the purer asphaltic products, gilsonite, wurtzilite and ozokerite, for other uses. Speaking generally, the rock asphalt is a sandstone or limestone naturally impregnated with asphalt to an extent that makes it an ideal road surfacing material without mixing or treatment other than crushing. The asphalt content of the commercial product runs 8 to 12 per cent.

Jan 1, 1933

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By Richard S. Fowkes

Advanced technology, including automation and computerized information systems, is being adopted in mining at an ever-increasing rate to improve safety and productivity and to decrease overall costs. This U.S. Bureau of Mines report focuses on the human factors issues related to advanced technology. Among the significant facts discovered were the following: Experts studying tile design adoption, and implementation of new technology have stated repeatedly that human factors specialists should be involved from the early planning stages, through design and fabrication, and up to and during production, since human factors has been consistently identified as the biggest obstacle to the efficient utilization of new technology. Also, middle management is generally the greatest obstacle to the adoption of advanced technology, this technology can give rise to worker alienation, boredom, stress, job insecurity, and a sense of isolation; training most of the present work force is more cost effective than hiring new workers; workers are willing to accept new technology if they are given a voice in its implementation; the social and the technical systems should be jointly optimized; and with the intro¬duction of advanced technology, the cognitive or mental, rather than the physical, aspects of human-machine interaction must be emphasized.

Jan 1, 1994

Jan 1, 1885

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

The Bureau of Mines is establishing design criteria for effective roof support systems and is developing technology to improve mine planning and design. Geologic studies, surface and underground mine monitoring, and laboratory evaluations were conducted. The seven papers in this proceedings Information Circular present results of several investigations. Addressed are problems existing in both longwall and multiple-seam mines. Discussions include the effect of dewatering at a longwall mine site in the Pittsburgh coal seam and the effect of chain pillars on subsidence. Other results are measurement and characterization of longwall rock mass movement and an integrated design for stability in multiple-seam mining.

Jan 1, 1987

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Federal Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and nil stifle.5 The. Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because anal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form Will Ire valuable. The material will he presented in three parts. as follows I. United Stares Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Other Foreign Patents. Part I appeared in early 1960. Part II follows.

Jan 1, 1962

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017