Search Documents

By A. J. Geldenhuys

This paper will focus on two topics, namely (1) an innovative process for the neutralization and partial sulphate removal of acid streams produced during coal mining and processing and (2)optimization of this integrated neutralization process by adding small amounts of synthetic organic polymers. The integrated lime and limestone process has been developed to neutralize acid mine water and to remove sulphate (to less than1 200 mg/l), magnesium and metals. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1 500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. The process consists of the following stages: 1. Limestone (CaCO3) neutralization to raise the pH to 7 and CO2-production. 2. Lime (Ca(OH)2) treatment to pH 12 for Mg(OH)2precipi-tation and gypsum (CaSO4.2H2O) crystallization. 3. pH adjustment with CO2recovered from stage 1 and CaCO3 precipitation. Retention times of 1 hour, 4 hours and 1/2an hour were required by stages 1, 2, and 3 respectively. The sulphate level was reduced to 1 094 mg/l, which is less than the original aim of 1 200mg/l. Chemical costs associated with neutralization, using limestone instead of lime, are reduced by 69% in the integrated limestone/lime process. The overflow water from the clarifier of each of the above stages generally contains a wide variety of colloidal impurities that may cause the water to appear turbid or may impart colour. This results in very slow sludge settling rates that cause overflow water with a high degree of turbidity and colour. There are a number of successive or simultaneous stages involved in the agglomeration of particles. To get optimum neutralisation of the acid water and partial sulphate removal to below the saturation level of gypsum (i.e. 1 500mg/l), maximum sludge recovery is needed. The higher the concentration of seed crystals, the larger the surface area. Therefore, effective removal of suspended and colloidal matter from the overflow of each stage is required and can be achieved by coagulation and flocculation. The polymers PAC6 and 3095 were effectively used as coagulant and flocculant respectively. The addition of these polymers resulted in a clear overflow in each of the above stages with a very low turbidity.

Jan 1, 2003

By D Bruce

OZ Minerals’ Carrapateena mine is a Sublevel cave mine located in South Australia, approximately 160 km north of the regional centre of Port Augusta. Carrapateena commenced underground development in 2016, with production commencing in 2019 and ramping up to 4.25 Mtpa by December 2020. In pursuit of continual improvement, the Carrapateena mining team sought to identify how it could better interrogate its current productivity levels and its drivers (root causes). During this process the team were confronted by a disconcerting number of different opinions (which often conflicted) on our actual productivity performance which led to a need for review. Although reliable data and a well-designed time utilisation model (TUM) existed, it was still unclear what actions needed to be put in place to improve productivity. This was for the following reasons: • Data sources were disparate unless significant effort was applied to compile them. • Data sources were not available in a format that could be easily viewed or analysed. • General understanding of the data which was collected and how it could be used was poor. • Process of regularly analysing performance and forming tangible actions to improve was lacking rigour. A project was then started with the goal to fix the areas stated above. An initial requirements gathering exercise was undertaken to identify key data sources for site which returned a staggering 42 known systems which were then shortlisted to the key systems that contained operational data and could generate tangible improvements when analysed. This paper discusses the approach to selecting the OZ Minerals Insights Hub as the chosen platform, and the effort and collaboration between cross-functional departments that was involved in transforming the data so it could be displayed in a useful way. The data sources identified included a fleet management system, two planning databases, a control system historian, and a mobile fleet machine data system. New processes were also introduced to digitally capture daily commentary; this was achieved utilising SharePoint Forms. Data pipelines were then developed in the Insights Hub platform to automate the ingestion and transformation of the raw mining data into curated data models for end user consumption. Tableau dashboard packages have been created to support facilitation of short interval control, daily review meetings, and weekly review meetings as well as data analysis of key equipment and locations. These dashboards visualise the mining data models in a form that provides the user a clear picture of what has occurred, why it has occurred, and where to focus improvement efforts. This has resulted in a team which is more accountable, more equipped to assess the root cause of performance, and more regularly able to make data driven decisions. The next step? To build this out from Mine to Mill and create a data indexing tool which will drive self-service reporting, a data agnostic platform and predictive tools that help our people continue to be one step in front.

Mar 29, 2023

By William Gleason

"The city of Denver, CO has experienced extreme growth in the past decade, with the population of the city topping more than 700,000 people in 2018. The current storm water drainage system was put in place in the early 1900s and has not been able to keep up with the growth of the city.When it rains north and east of the city, the runoff goes toward the South Platte River. With the dense population and sometimes severe thunderstorms in the summer, the city has experienced significant flooding that not only endangers lives of residents, but some of the storms have caused millions of dollars of property damage.The Platte to Park Hill Project is a $298-million nearterm, four-phase solution to the flooding that includes the Globeville landing outfall; an open drainage project in the Cole neighborhood in north Denver; an area for temporary water detention and another temporary water detention in Park Hill.The largest and most complex phase of the project is the Globeville landing outfall — a $70-million box culvert project that includes a pair of 157-m (515-ft) long, 243-cm (96-in.) diameter storm water tunnels that pass beneath a busy rail yard with 17 tracks for the Union Pacific Railroad (UPRR) and two Regional Transportation District (RTD) commuter rail tracks. The tunnels, which were installed parallel to a pair of existing 243-cm (96-in.) tunnels, were designed by Brierley & Associates as a client of Merrick & Company for the City & County of Denver, and Bradshaw Construction constructed the one-pass tunnels.From the start, it was evident that the tunneling portion of the project would be the most challenging because of the rail yards.“It’s a little bit more complicated because the railroads have such tight restrictions for settlement,” said Rebecca Brock, Brierley’s project manager. “We had a lot of meetings with Union Pacific and RTD to figure out what are prescribed versus tolerable settlements.”“The portion extending beyond the UPRR under the RTD rails was challenging, as RTD is new to tunnel installations under its tracks,” said Lester Bradshaw, president of Bradshaw Construction. “The RTD tracks employed a unique foundation of continuous concrete with integral raised concrete ties on rubber bushings. Minimizing settlement to these tracks was a critical requirement.”"

Jan 9, 2018

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By Walter S. White

The Michigan native-copper district has produced about 5,400,000 tons of copper since mining began in 1845. The copper occurs primarily as open-space fillings and replacements in amygdaloidal flow tops and conglomerate beds of the Portage Lake Lava Series, of middle Keweenawan age. Secondary minerals with which the copper is associated include microcline, chlorite, epidote, pumpellyite, prehnite, quartz, and calcite; zeolites, other than laumontite, are not abundant. A zonal pattern of the secondary minerals transects bedding and suggests regional metamorphism mainly to the grade of the prehnite-pumpellyite graywacke facies of Coombs. Most of the major copper deposits are near the upper limit of abundant quartz in this zonal pattern. The distribution of copper in both amygdaloid and conglomerate deposits is controlled partly by primary permeability of the rocks and partly by later tectonic fracturing that was concentrated in the mechanically weak flow tops and sedimentary beds. Ore shoots and deposits are therefore controlled partly by primary structural features, such as areas of thick and thin fragmental amygdaloid or the boundaries of conglomerate lenses, and partly by regional structure: a number of ore deposits are in synclinal downwarps. The copper-bearing solutions that formed the deposits were ascending. They may have come from a large concealed intrusive, or may have been driven out of the porous tops of lava flows when the rocks were compacted and metamorphosed at great depth in the central part of the Lake Superior syncline. The second hypothesis seems more consistent with the widespread distribution of the copper, its relation to mineral zoning that represents truly regional metamorphism, its native state, and the likelihood that copper deposition was later than most or all of Keweenawan volcanism.

Jan 1, 1968

By Ree Llewellyn

"It has been estimated conservatively that the costs of wear damage and friction in the Canadian mining and mineral processing industry amount to over one billion dollars per year. These are mainly incurred through the repair or replacement of worn parts and production losses from related equipment downtime. The selection and application of the most appropriate wear protection components and systems, can thus have a very significant influence on productivity, profitability and global competitiveness.Details are presented of the wide diversity of materials used to counteract the varied and often complex wear attack mechanisms that occur in surface mining. The majority are various forms of steels and irons with generally very high hardness. However, they also include relatively soft elastomers and polymeric products.The main characteristics and applications of the different classes are reviewed. Case studies record significant performance improvements achieved through more judicious selections. Finally, some new developments which reduce maintenance charges by substantially increasing wear component life, are described."

Jan 1, 1996

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By C. W. Siyasiya, K. A. Annan, W. E. Stumpf

"SynopsisThe relationship between niobium content and austenite grain growth has been investigated through hot rolling simulation on a Bähr dilatometer. The effect of delay time between passes during rough rolling in Nbmicroalloyed steels with nitrogen contents typical for electric arc furnace (EAF) melting was studied. The results indicate that the grain growth constants n, Q, and A increase with an increase in Nb content. The activation energy for austenite grain growth Q was found to be in the range of 239 to 572 kJ/mol, the exponential constant n ranged from 2.8 to 6.2, and the material and processing condition constant A from 4.24 × 1012 to 4.96 × 1028, for steels with niobium contents ranging from 0.002% Nb to 0.1% Nb. A general constitutive equation for the prediction of austenite grain growth in these Nb-microalloyed steels under rough rolling conditions has been developed. Good agreement between the experimental and the predicted values was achieved with this constitutive equation.IntroductionGrain refinement has been found to increase both the strength and toughness of steels (Gao and Baker, 1998; Sharma, Lakshmanan, and Kirkaldy, 1984; Seok et al., 2014; Maalekian et al., 2012). It is also known that the austenite grain size directly influences the microstructure, and thus the mechanical properties, of the steel (Maalekian et al., 2012; Yue et al., 2010). Effective grain growth control is reported to be achieved through addition of precipitate-forming elements, such as Nb that, slow down the grain boundary migration through pinning and solute drag mechanisms (Yu et al., 2010; Olasolo et al., 2011; Alogab et al., 2007). Much work has been carried out on austenite grain lsize control by the addition of precipitate-forming elements that have a strong affinity for interstitial elements, such as carbon and nitrogen, which form the dispersed pinning particles to inhibit the austenite grain growth (Alogab et al. 2007; Hodgson and Gibbs, 1992; Nanba et al., 2003; Flores and Martinez, 1997; Rollett, Srolovitz and Anderson, 1989). Austenite grain growth can be described using a conventional or a modelling approach. With conventional approaches (e.g. metallography), in-situ monitoring of austenite grain growth at high temperatures is impossible. Modelling the grain growth behaviour based on available data is the ideal option. To quantitatively describe austenite grain growth therefore requires development of a sound mathematical austenite grain growth equation that accounts for the effects of the varying microalloying elements in inhibiting austenite grain growth. Numerous attempts have been made to develop an empirical model based on the general equation developed by Sellars and Whiteman (1979). Many of these models do not account for the direct effects of the microalloying elements such as Nb in austenite grain growth control [Fu et al., 2011; Wang and Wang, 2008; Wang et al., 2006; Shanmugama et al., 2005; Banerjee et al., 2010; Pous-Romeroa et al., 2013). The current work has considered this limitation, taking into account the direct effect of niobium in grain growth control during thermal processing. This is done by incorporating the initial austenite grain size Do and the microalloying element niobium in the development of a constitutive equation for grain growth prediction in Nb-containing microalloyed steels."

Jan 1, 2015

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead "blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

Refractory gold ores have been the subject of intensive metallurgical study in order to achieve more efficient recovery of contained values and at the same time to minimise environmental impact. Considerable innovative gold processing technology was introduced in New Zealand last century, the most notable being the first successful commercialisation of the cyanidation process by the Crown Mines Company at Karangahake in 1889. The Karangahake gold-silver deposit was second only +to the Waihi Martha mine in total bullion production from the region with active mining from 1882 until about 1920 and sporadic production between 1930 and 1944. Reevaluation at Karangahake with associated metallurgical testing has continued since that time becoming particularly active in the last decade as a result of increasing gold prices. Gold processing technology is reviewed and results of some recent test work are presented and discussed in the context of Karangahake history and future development possibilities. This work confirms the variability and complexity of the Karangahake deposit both mineralogically and metallurgically and suggests flotation followed by new and innovative smelting is the most appropriate processing route for the recovery of gold from the high grade ore which could be produced from the Karangahake workings in moderate tonnages.

Jan 1, 1993

By Yazen Khasawneh, Yao Zhang

Upgrading and maintenance programs were proposed at a power generating plant in Indiana. To perform construction activities associated with the proposed upgrading and maintenance, a LR11350 crawler crane with a dead load of 1,500 ton was required in the vicinity of existing plant structures. The contact pressure from the crane tracks for the heaviest lift, maximum reach and angle (worst loading condition) were estimated by the rigging engineer to be on the order of 84 psi. Several concerns were raised regarding the total and differential settlements while the crane is in operation and the induced stresses on existing underground utilities due to crane loads. Three-dimensional finite element simulations were conducted using hardening soil model for the subsurface soils and elastic model for the other structural elements (underground utilities and crane mats) to optimize the configuration of the proposed crane foundation. It was found 1-foot thick engineered steel mats underlain by a 1.5-foot thick crushed stone pad will provide enough support to the crane. It will also control the settlement to the allowable limit and maintain the stresses in the underground utilities within tolerance. INTRODUCTION A LR11350 heavy lift crawler crane was proposed as part of an upgrade program at an existing power plant in the state of Indiana. The proposed crane will be sitting on an open ground in the vicinity of existing plant facilities, with multiple underground utilities going beneath the proposed footprint of the new crane pad. The existing utilities are of diverse kinds, including sanitary sewer corrugated metal pipes, electrical conduits and variable steel water/oil drain pipes. The safety and functionality of these underground utilities are critical to maintain the proper operation of the power plant. Therefore, the design of the new crane pad foundation system is of essential to control the ground settlement and the imposed stresses to the existing utilities (Davie et al., 1998, Scott 2017). To ensure all utility locations and depths are identified, the proposed footprint was thoroughly surveyed. Information in regard to each identified utility was provided by the owner. Subsurface explorations were conducted using geotechnical soil borings and soundings to evaluate the ground conditions and generate soil profiles. Numerical simulation and analysis utilizing finite element method were performed to design the crane pad foundation system and evaluate the responses of the utilities. This paper summarizes project information, geotechnical conditions and then focuses on the finite element analysis in assisting the design of crane pad and the utilities evaluation.

Jan 1, 2019

By J. C. Ion, O. Isaksson, J. Stjernberg

Iron ore pellets are a preferred feedstock for ironmaking. One method used for pelletizing is the grate-kiln process, first established in 1960.During the past decade, the establishment of new grate-kiln plants has increased rapidly, especially in China, and new constructors of pellet plants have started to operate in the market. It is well known that the grate-kiln method yields a superior and more consistent pellet quality compared with the straight-grate process. However, certain issues exist with the grate-kiln plant, which are discussed here, together with proposed practical solutions.

Jan 1, 2015

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By T. R. Ellis

The valuation of mineral properties in the U.S. is only partially regulated. The regulations which have jurisdiction or impact appear to have such mainly as a consequence of unintended fallout, since the regulations were designed for other purposes. Court case history can also be important. The combined results are a mixture of bad and good, with important lessons to be learned. Since 1981, the Securities and Exchange Commission has prohibited U.S. listed companies from reporting quantitative estimates of mineralization and the value of mineralization, other than proven and probable reserves. This results in the minerals appraiser (valuator) working with a shortage of data in his everyday work, both on the subject property and in sales analysis. Between 1989 and 1995, all 50 states and essentially all federal agencies adopted the Uniform Standards of Professional Appraisal Practice (USPAP) for real property appraisals (valuations). The major national appraisal societies also require their members to abide by USPAP. A significant portion of minerals appraisals must now follow these standards. This paper will discuss the content of USPAP. It provides a very good framework for the valuation of a minerals property or a mine, both as real property and as a business. However, the credentialing standards for real property appraisers are now prohibitive for minerals appraisers.

Mar 1, 2002