Search Documents

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By Robert Leach

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

With the advent of the environmental "green" movement of the 1960s, eventually leading to Earth Day 1970, Congress responded by passage of the National Environmental Policy Act (NEPA), 1970. NEPA gave impetus to a flood of federal acts and laws in the subsequent three decades. Many of those protecting man's environment, health, and well-being also affect mining. For purposes of this chapter, a current mineral law summarization lends itself to a division into two parts: viz., Part I, General Mining Law, and Part II, Enviromining Law. The word enviromining has been coined by the author and is defined and used herein as those federal and state statutes and regulations that were created to provide protection and preservation of man's environment, health, safety, and welfare, and they have particular application to and affect on mining activities. They are listed and treated under Enviromining Laws in Part II. Mining, as a basic industry to provide the essential minerals for mankind's necessities and well-being, truly reflects the mining industry's slogan, "If it can't be grown, it must be mined." Without the basic minerals and rocks won from the earth by mining and mineral processing for their valuable physical properties or chemical constituents, man would soon be forced to revert to the cave-dwelling age. Unfortunately, for man to survive in the "manner of life to which he has become accustomed," he is caught between the demands of cleaning up his deteriorating environment and a continued supply of his basic requirements and amenities for daily living supplied by mining of the earth's minerals. He must have "clean living" at the same time with "good living;" neither is expendable. A very high pricetag accompanies this essential and critical choice which must be paid by society. The United States is internationally recognized as the world leader in environmental matters. Many countries are following suit, principally the other Anglo nations. Because US law is founded and based on English law, on occasion, Anglo-American law is referred to and cited as authority in litigation anywhere in the Anglo-American world of jurisprudence. For this reason, and because mining and the industry is international in nature and operations, some British Commonwealth cases will appear in various topics. If the case is of interest to the reader, further inquiry at a law library may be made through use of the case's style and citation given. "Style" refers to the name of the litigating parties. "Citation" refers to the law publication in which the case and decision may be found, as well as the jurisdiction and court of decision. Citation of cases from the United States and British Commonwealth nations is explained under Case Citation Explanation. Space and time limit exhaustive treatment of subjects and covering all geographic and jurisdictional areas. This chapter is intended as a broad outline and is based on the author's master's thesis at the University of Missouri-Rolla, 1992. The following Case Citation Explanation provides guidance on formatting of citations.

Jan 1, 1994

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By AIME AIME

THE John Fritz Medal Board of Award, at its annual meeting on Jan. 21, 1921, awarded its gold medal and diploma to Sir Robert Hadfield for the invention of manganese steel. On June 1, announcement was made that the Board of Award had awarded its gold medal and diploma to Charles Prosper Eughe Schneider for "achievement in metallurgy of iron and steel; for development of ordnance, especially the 75-mm. gun, and for notable patriotic contribution ' to the winning of the war." The award to Sir Robert Hadfield is for the year 1921; the award to Mr. Schneider is for 1922. The latter was made at this time in order that the medal might be presented by the group of American engineers now visiting England and France.*

Jan 1, 1921

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By P B. Card

"The website www.economicevaluation.com.au, which had its origins at the Project Evaluation Conference 2009, provides a free way for industry professionals to teach themselves economic evaluation. At its core is a set of fast-moving modules and three worked examples.The website recognises that economic evaluation is a discipline with a hierarchy of three levels:decision-makingevaluating the project/businesshands-on modelling.There are a set of modules for each level that describe the concepts and activities in detail. These emphasise that the most important and rewarding work is the evaluation of Level 2. The economic model created in Level 3 is merely a working tool and should not become a sophisticated ‘trophy’ in Excel that only one or two people can comfortably use.Hands-on modelling contains three sets of practices designed to make any model rigorous and intuitive so that it can be easily understood and used by others in the project team. Even if the model develops into a long, detailed and complex workbook, it should remain easy to follow and be intuitive. The website advocates freedom to devise any architecture that best suits the project under study, but promotes rigour through the following practices:four cash streams and graphsthree architectures – concept, prefeasibility and feasibilitysix principles.The modules in the Level 2 evaluation use conversational language to describe in detail the broad range of activities needed to properly understand and characterise a project/business. It stresses that net present value is nothing more than the mathematical treatment of a whole set of opinions, is not an absolute truth and is only a fraction of the evaluation process. The modules describe in detail the range of economic metrics that should be computed and the full spectrum of equally important characterisations required to make the decision in Level 3.CITATION:Card, P B, 2016. Teach yourself economic evaluation, in Proceedings Project Evaluation 2016, pp 160–171 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

INTERNATIONAL conferences on safety in mines originated in 1912 when, in response to an invitation issued by the United States, representatives of Austria-Hungary, Belgium, France, and Germany participated in a conference held in Pittsburgh, Pa The record shows that a permanent organization was proposed to be developed through. diplomatic channels. However, the advent of war 2 years later prevented this proposal from coming to fruition. No further cooperation between the Bureau of Mines and a group having: similar interests in a foreign country took place until 1924, when formal cooperation with the Safety in Mines Research Board of Great Britain was established. Interchange of personnel and results of research under that arrangement have resulted in a number of publications in both countries and more rapid advance in knowledge than could have been obtained through the same efforts exerted independently.

Jan 1, 1950

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975

By Paul M. Tyler

According to Lindgren , the economic importance of pegmatites stems from the fact that they represent the principal natural storehouse of two classes of mineral products : (1 ) common minerals in exceptional size and purity and ( 2 ) several of the rarest minerals , which are not commercially available from other types of deposits . Most pegmatites can be described simply as coarse- to very coarsegrained granites . Pegmatite includes coarse -textured igneous rocks of any composition , such as syenitic , alkali syenitic , dioritic , or gabbroitic ; but basic pegmatites are far less common than those that are associated with acid rocks and correspond approximately to the mineral composition of ordinary granite . Moreover , only a very few basic pegmatites can be considered as economic sources of useful minerals . Whereas , in ordinary granitic rocks the individual minerals usually measure 1/8 to 1/4 inch across , in pegmatites they are characteristically over 1 inch and often more than 12 inches in diameter . Although some of the constituents of the pegmatite may be only a fraction of an inch in length , single crystals more than 10 feet long are by no means unusual , and some crystals are enormous . A whole quarry was operated in the Urals within a single crystal of feldspar . Huge quartz crystals are quite common although usually imperfect . Muscovite plates 10 feet in diameter have been mined in India , and the Purdy mica mine in Canada contained a mica crystal measuring 6.5 by 9.5 feet and weighing nearly 7 tons , which supplied more than $20,000 worth of trimmed mica sheet . A loglike crystal of spodumene in the Etta mine in the Black Hills of South Dakota was 42 feet long . Giant crystals of beryl weighing several tons apiece have been mined from several properties . Because so many rare minerals are found in substantial concentration only in pegmatites , it is a common fallacy to suppose that pegmatites are always enriched in rare elements . Traces of most of these elements , of course , are found in almost all igneous rocks , and they reappear in the sediments derived from igneous rocks . It does not follow , however , that all or even most pegmatites contain higher percentages of rare elements than other granitic rocks . Geological evidence points to the probability that notable concentrations of rarer minerals or elements in pegmatites are more or less fortuituous , such additions often being ascribed to events subsequent to the original emplacement of the main body of the pegmatite . Most pegmatites consist principally of potash , feldspar , and quartz . Even mica , although commonly present , is not an essential constituent . Probably

Feb 1, 1950

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. T. Randall

Several years ago investigations were begun by the United States Government to determine the most efficient methods of utilizing the coals of the United States. These investigations, which were continued along several different lines, are now being carried on by the Bureau of Mines, in accordance with the provisions of the act creating this bureau . . It was because of the need for more complete information concerning the conditions under which coal could be economically burned in boiler furnaces without objectionable smoke that tests were made at the Government fuel-testing plants at St. Louis, Mo., and Norfolk, Va. In addition to this experimental work a number of commercial plants in the larger cities were inspected to ascertain what were the best methods then in use for abating smoke. The results of these investigations were reported in Bulletins 334 and 373 of the United States Geological Survey. Because of the continued demand for the information contained in these bulletins, the original editions of which are exhausted, they are reprinted by the Bureau of Mines. The text of this bulletin, particularly the information relating to smoke ordinances, was revised in the latter part of 1910 and the early part of 1911 by S. B. Flagg, engineer, who has charge of the steaming tests being conducted by this bureau.

Jan 1, 1912

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014