Search Documents

The Aberfoyle Tin Mine lies on a wide sloping bench about 2,000-2,500 ft. above sea level, at Rossarden, 14 miles north of Avoca, in north-eastern Tasmania. The quartz-cassiterite veins were discovered in 1916, but mining did not begin until 1926. Trenching revealed seven small tin-bearing veins within a width of 57 ft. of Palaeozoic slates and sandstones, and it was assumed that the mineralization extended beneath the adjacent cover of Permian strata, but the presence of the main vein system (the 26 Vein System) was not suspected until the Aberfoyle Fault was discovered late in 1928.The mine has now been developed on thirteen levels, to a depth of 1,350 ft. The lower limit of economic mineralization appears to lie at about the ll-level, which is 1,060 ft. vertically below the concealed outcrop of the main veins. Production of tin and tungsten concentrates began in 1932, and to date more than 550,000 tons of ore have been mined for a recovery of 8,856 tons of tin concentrates, and 3,056 tons of wolfram concentrates, valued at approximately £6,500,000.This paper reports part of an investigation undertaken by the Mineragraphic Investigations Section of C.S.I.R.O. to study the mineral composition of the ore in relation to the apparent failure of cassiterite and wolfram mineralization to extend below the present working limits of the mine, and was first issued as Mineragrapnic Report No. 639.GENERAL GEOLOGY:The deposit consists of a series of quartz veins in a northsouth trending sheeted zone, transecting folded slates and...

Jan 1, 1957

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By J Lea, P Hatherly, J L. Edwards

Coal exploration has traditionally involved the acquisition of data to enable a resource to be quantified and qualified to the extent that its economic potential can be determined. This process commonly relied on: drilling to determine the depth and thickness of coal seams, broad characterisation of the overburden and interburden, and to provide cores for coal quality analyses; basic wireline logging to cross-check the depth and thickness of coal seams and provide some indication of rock mass strength; and basic surface geophysics and remote sensing to identify major geological structures. In recent years, the adoption of the JORC Code as a basis for the reporting of resources and reserves has placed a greater emphasis on the need for detailed, reproducible data sets that not only satisfy the traditional requirements of mine planners, but also satisfy the governance requirements of corporate and financial institutions. Similarly, the development of sophisticated numerical modelling techniques for use in both open cut and underground mine design, has seen a greater demand for precise geotechnical data, in situ stress characterisation and hydrological information as routine input to the design process. These requirements, coupled with the prevailing trend toward high capital, relatively inflexible mining techniques less tolerant of geological surprises, and the need for consideration of environmental issues such as groundwater impacts and surface subsidence, requires that modern exploration programs be multifaceted, and designed to commence capturing data relevant to ædownstream issuesÆ even during the initial phases of exploration planning.

Jan 1, 2009

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27'6" diameter, 78'O" deep Brandywine Street - 30'6" diameter, 88.6' deep Ellicott Street - 33'0" diameter, 110'0" deep

Jan 1, 1985

By G. V. R. Landman

In the early days of underground coal mining, the use of explosives to break coal resulted in a large number of disastrous methane and coal dust explosions and consequential loss of life. Research by the British, French, US authorities, amongst others, introduced many practices that significantly reduced the occurrence of such incidences. The use of explosives designed to be safe in a methane atmosphere, plus the creation of a second free face were two such practices which became commonly used in coal mines all over the world including southern Africa. With its associated coal cutting equipment and labour, the cost of creating a second free face is significant and this, together with the constant drive to reduce mining costs in a competitive market, causes mine management to regularly question the need for the second free face. Also, the safety and nature of permitted explosives has changed considerably since the days of black powder and nitroglycerine-based explosives with the introduction of water-based explosives. In southern Africa mining regulations pertaining to the blasting of coal has its origins in British research which was largely done in the first half of the twentieth century. More recent research by the US Bureau of Mine has resulted in a deeper understanding of some of the mechanisms of methane ignition by explosives and suggests that some of the earlier regulations can be relaxed to a certain extent without compromising safety. This paper gives an overview of the original research done in Europe and the more recent work in the USA, to give mine management and regulatory authorities a deeper understanding of the important safety issues when using explosives in a methane atmosphere. It also suggests that blasting off the solid is no less safe than using a second free face providing certain safety procedures are followed.

Jan 1, 2000

By P Mulvey, M Stuckey

"Inter-aquifer leakage due to fractures caused by coal seam gas extractions or longwall mining is an important issue for both the gas and coal industries. Currently, predicting stress induced macro-porosity associated with hydraulic fracturing, depressurisation via dewatering or collapse of overlying seams to infill a void left by longwall mining, is problematic. If fractures can be located the fracture can be sealed. Locating fractures is difficult. The non-geophysical approaches to locate fractures has been to consider the mixing of different waters, particularly that of more recent shallower groundwater with older deeper groundwater, via differences in radio-isotopes integrated with geochemical models to predict likely mixing of waters. This approach is applicable under appropriately complex settings; however, it is an expensive technique and is based on the assumption that the daughter isotopes are equally non-reactive which may not always be the case.Potentially a cheaper and faster technique is to consider integrating geochemistry (mineral weathering) and hydrogeology. The chemistry of groundwater, controlled by the weathering of primary rock?minerals and?formation of secondary minerals, can not only be differentiated between geological strata but also within strata as different stages in weathering results in differing impacts on water quality (ie different reactants).Field analysis of pH, electrolytic conductivity (EC), oxidation reduction potential (ORP) and dissolved carbon dioxide together with laboratory analysis of dissolved constituents characterise the chemistry of the water. Collection of rock samples at the time of drilling for bore installation can provide the (only) opportunity to assess the media in which the groundwater resides and migrates through. An assessment of aquifer matrix chemical makeup, via bulk sample chemical analysis, X-ray diffraction (XRD) and petrographic analysis can achieve this.The chemistry of groundwater is dependent on the water velocity. Water at deposition and post-diagenesis dissolution of minerals by hydrolysis and oxidation will result in equilibria of the dissolved phase with the solid phase. Post-depositional fractures caused by either tectonic activity or weathering alter the rate of weathering and thereby the geochemistry. Slow water flow in microfractures results in water in equilibrium with the rock minerals. Faster flow in larger fractures results in water being in disequilibria with rock minerals.Fractures can alter groundwater chemistry by two pathways: changing groundwater velocity, which changes the rate of hydrolysis or oxidation mixing water from different geological strata.Both pathways cause subtle changes in the water chemistry.It is however, the dissolved phase chemical data, which can be observed over time at individual locations and/or at a point in time along a flow path, which allows the hydrogeologist to ælook up-gradientÆ and locate the zone of leakage. Hence, influences on rock/groundwater chemistry, from anthropogenic sources to natural mixing of waters, can be assessed via appropriate interpretation of geochemistry, hydrogeochemistry and flow data.This paper will use the example of the geochemical and hydrogeological characterisation of aquifers within the Hawkesbury and Bulgo Sandstone of the Southern Coalfields to the south of Sydney in New South Wales to demonstrate this approach.CITATION:Stuckey, M and Mulvey, P, 2013. Looking for fractures - integrating geochemistry with hydrogeology to find inter-aquifer leakage above dewatered or collapsed coal seams, in Proceedings Water in Mining 2013, pp 99-108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Don Ibana

Supported by the Minerals Council of Australia (MCA) through the Minerals Tertiary Education Council (MTEC), three Australian universities–Curtin University, Murdoch University and the University of Queensland–have formed the Metallurgical Education Partnership (MEP) to jointly develop and deliver an engineering design capstone unit–Metallurgical Process and Plant Design–in their respective undergraduate programs in extractive metallurgy, in order to enhance the students’ educational experience. A unique feature of the program is the close interaction of the students in all three universities and a significant involvement of industry professionals. Now in its sixth year, it is clear that this unit is achieving its objectives

Jan 1, 2014

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By Bern Klein, Malcolm Scoble, Justin Widdifield, Andrew Bamber

"It has been suggested that the pre-concentration of ore underground can bring positive economic and environmental benefits to underground mining, particularly at extreme depth. The integration of mineral processing systems for coarse waste rejection and disposal into the underground mining environment has a substantial impact on the economics and operation of the mine. A case study for the integration of underground pre-concentration at Falconbridge’s Thayer Lindsley and Fraser Copper operations in Sudbury, Ontario is discussed, with particular focus on ore evaluation, system design, integration, and impacts on the operation. Conclusions as to the overall feasibility and potential impacts of underground pre-concentration are presented.INTRODUCTIONObjectivesA scoping investigation has been conducted for Falconbridge Ltd on the Fraser Copper Zone and Thayer Lindsley mines in order to develop a better understanding of the operations, and to do a preliminary evaluation of the potential for pre-concentration of the ore underground. The objective was to develop a conceptual design and evaluation of a pre-concentration system for each site. The results are to be used as the basis for a more detailed future study.Underground Pre-ConcentrationThe pre-concentration of ore to reduce the quantity and improve the quality of material transported to the processing plant is not a new concept and has been in practise at several mines including the American Zinc Company in Mascot Tennessee (Munro et al, 1982), the Sullivan Mine in British Columbia and presently at Xstrata’s Mt Isa lead-zinc mine in Australia, as well as at several PGM mines operating in the South African Bushveld. For each of these mines, a high degree of waste rejection was achieved at a coarse particle size with good metallurgical recoveries. The benefits arising from the surface pre-concentration of ore are well documented in the literature (McCullough et al, 1999; Miller et al, 1978; Munro et al, 1982; Schena et al, 1990; Sivamohan & Forssberg, 1991)."

Jan 1, 2006

By Li Zhang, Jing Zhao, Chuanwei Zang, Shuanlin Wang

The application of gob-side entry retaining (GER) in steeply pitching seam longwall mining with a hard roof has always been a difficult problem. Based on the simplified roof beam mechanical model, the traditional gob-side entry retaining by packing (GERP) roof structure evolution process and its problems with use in steeply pitching seams are analyzed. Therefore, based on the unique characteristics of the gangue rolling and accumulating in the steeply pitching seam, this contribution proposes an innovative method of gob-side entry retaining by roof cutting (GERRC) in steeply pitching seam and details its technical process. The roof structures of the GERRC and the GERP are compared. Taking the Chang Gouyu Coal Mine as a case study, field experiments were carried out. This research finds that the GERRC can both overcome the impact of rolling gangue on roadside support and make the rolling and stacking gangue become a roadside support. The roof structure of the GERRC is in a one-time statically indeterminate state, which is conducive to the stability of the roadway. In the field test, the total displacement of the roadway roof and floor is 97 mm, the supporting pressure of the serried single props is less than 28 MPa, and the props have no obvious bending phenomenon.

May 6, 2020

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By Steven J. Knoll, Theodore J. Williams, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 18 and 40 m, and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.