Search Documents

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By J Dwyer, M Hill

Downer’s mining division has made an operational and financial commitment to developing engineered solutions that mitigate the risks associated with operator proximity to uncontrolled development drill boom movements, and unguarded rotating drill steels.With the potential for serious injury or fatality, these identified risks are categorised as critical. Previous attempts by the industry to engineer them out have produced limited success, with numerous incidents still occurring year on year. Ultimately, the industry (as a whole) remains reliant on procedural prevention for operator safety.Downer understood the success of such an initiative would largely depend on the effective collaboration between operational experience, technology experts and automation. With so many variables requiring consideration; such as physical operator movement, machine boom movements, variable machine positions, and underground environmental impacts – challenging traditional technologies was necessary to deliver an optimal solution.For that reason, discrete detection (similar to laser curtains or beams) was considered not fit for purpose. The use of situational mapping, using rotating lasers, however, provided the optimal solution. The lasers collect data that is then processed using a custom software application.The software application is specifically programmed for tracking and classifying objects within detection zones, using advanced algorithms and filtering. Recognition and removal of non-positive disturbances are possible without losing personnel detection capability. The detection of relevant classified objects (humans) is determined by analysis of object size, age, movement, and speed etc. When the relevant object is detected, an alarm and inhibit function is applied preventing drilling functions.Any breach of the safety zone (forward of the front jacks) will automatically disable the hydraulic boom function. This can only be reset in the cabin once the person or persons have returned past the front jacks of the development drill into the safety zone.Downer, in collaboration with partner YUMARR Automation, has successfully developed this reliable boom isolation system, and is called JumboGuard. The system has now been commissioned and installed across all Downer Mining development drill fleets, operating in Australia.CITATION:Hill, M and Dwyer, J, 2017. JumboGuard – automatic boom isolation system, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

The Estonia Mine, operated by Eesti Energia Kaevandused AS (EEK), the mining division of the Estonian Government's energy company, Eesti Energia AS, is a large room and pillar mine located in Eastern Estonia. It supplied approximately 4.9 Mt/a of oil shale in financial year ending 2010, which is used for electricity and shale oil generation. Due to the Estonian climate and the power station's need for a dry product, Estonia Mine has developed a planning system where short-term demands of the power stations dictate the schedule. Such an arrangement requires maximising flexibility and consequently the mine only operated for 199 days in 2010.The footprint plays a key role in achieving mass mining rates as the 12 km + 12 km lease area allows the mine to split into mining districts that act independently of each other and maximise the number of work areas available. Coupled with this, the geology of the mine is relatively homogenous over the mining lease, simplifying the mine design and production methods.During the last five years, EEK has commissioned a comprehensive conveyor network. Consequently, material handling only requires loaders to dump oil shale direct from the production face onto a chain conveyor that feeds the conveyor network that ultimately supplies the enrichment plant. Dewatering is also of critical importance, with 90 Mm3 of water discharged annually. EEK uses large trenches up to 3.5 m deep and 1.2 m wide to channel groundwater. Track mounted mechanical saws are used to cut slots in the floor, to control overbreak in blasting these trenches.EEK has introduced Salzgitter Machinenbau GB 280S auger drills that drill three 280 mm diameter holes simultaneously. This has improved void hole drilling times and reduced the drilling required for each face, reducing the overall production cycle time. Blasting activities have also been decoupled from other mining activities negating the need for firing times through the use of small independent firings, required to control vibrations.

Dec 6, 2010

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By S F. Simmons

The Ohaaki Rhyolite and the Rautiwiri Breccia are two volcanic units occurring in the shallow and deep parts of the Broadlands-Ohaaki geothermal system. Alteration of these units by chloride waters results in distinct mineral assemblages that also have distinct whole rock compositions. The Ohaaki rhyolite is altered to an assemblage dominated by quartz, adularia, illite and pyrite as a consequence of silica, potassium and sulfur metasomatism. Locally, these rocks contain up to 0.5 ppm Au. The Rautiwiri Breccia by contrast is altered to an assemblage dominated by albite, adularia, quartz, illite, chlorite and pyrite in association with modest sodium metasomatism. Whole rock oxygen isotope compositions of altered rocks range between 3.3 and 7.5 ë, and are generally lower compared to their fresh rock equivalents having values of 9.5 to 10.6 ë; the result is broad pattern of lower values with increasing alteration intensity.

Jan 1, 2002

By Liane L. M. Kacinuck

This U.S. Bureau of Mines publication is intended to provide mining industry representatives and regulatory authorities with a reference package dealing with studies on hydrology and underground mine subsidence. An annotated bibliography and a list of additional sources are given and represent references published prior to June 1993. Ninety-two references ware identified and 72 obtained for assessment. Annotating the references included evaluating the study methodology and summarizing the basic results. The references are also compiled based on geographic location to aid the user in identifying articles of particular interest.

Jan 1, 1994

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By Vernon C. Davis

"SUMMARY AND CONCLUSIONSIn initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining.The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost.This report is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges.Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage.In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested.Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes.Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows parallel to one of the series of joint planes.Methods of detonation made little difference in breakage; but the millidelay caps produced the best conditions for moving the broken rocks."

Jun 1, 1953

By John Chipman, Wayne L. Worrell

Using recent thermodynamic data for the carbides and oxides of tantalum, columbium, and vanadium, the stable solid phases aboue 1300°K and at 1 atm CO(g) pressure in each M-C-O system have been determined. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures necessary to obtain these metals by carbothermic reduction under reduced pressures. TANTALUM, columbium, and vanadium react with carbon to form the M,C and MC carbide phases. The M,C carbides have narrow homogeneity ranges, but the MC phases possess considerable ranges of homogeneity.' The free energies of formation of the MC carbides were recently measured, and those of MC and M2Ccarbides have been estimated., (The notations MC and MC denote, respectively, the carbide compositions at the carbon-rich and at the metal-rich boundaries of the homogeneous MC phase.) In this paper, these carbide data are combined with thermodynamic data for the oxides to predict the stable phases in the Ta-C-O, Cb-C-O, and V-C-O systems at specified temperatures and oxygen pressures. M-C-O PHASE DIAGRAMS The solid phases in equilibrium above 1300°K for each M-C-0 system are shown in Figs. 1, 2, and 3. Above 1300°K, the vapor would consist entirely of carbon monoxide; and these phase diagrams were obtained by specifying the vapor pressure of CO(g) to be 1 atm. The temperature at which any two solid phases become unstable is specified along the two-phase equilibrium lines in each diagram. To simplify the diagrams, all solid phases in the Ta-C-O and Cb-C-O systems are represented as stoichiometric compounds. However, the homogeneity ranges of VO and VC are indicated, because they form a complete series of solid solutions.3 It also should be noted that the homogeneity range of

Jan 1, 1964

By S. Kariyawasam, R. McNealy

Pipelines are subject to multiple threats often requiring quantification of pipeline risk and engineering evaluation of in-line inspection and other data to effect discovery of conditions defined by the regulation. Public concern and pressure from regulatory bodies are accelerating the need for pipeline operators to formalize and intensify their approach to integrity management. Most operators need a phased approach to progressively adopt the most relevant and needed assessments. The organized and relevant assessment steps need to be introduced according to data available and maturity of the integrity management program. Each refinement to the quantification offers distinct advantages to the user. In this paper, the progressive integrity assessment solutions using quantitative methods are presented. Methodologies for engineering evaluation of integrity in-line inspection data for immediate and future integrity are summarized. Corrosion is used as an example, but the approach is applicable to any time-dependent defect based hazard. Strategies for pipeline integrity management are discussed.

Jan 1, 2005

By Ádria Rocha Corrêa

Durante a solidificação de ligas metálicas, o produto fundido se contrai, o qual provoca o surgimento de espaçamentos vazios na interface metal/molde chamados de “gaps”. Estes gaps causam o aumento da resistência térmica influenciando em toda a cinética da solidificação. A transferência de calor durante a solidificação depende do conhecido parâmetro chamado de coeficiente global de transferência de calor ( hg). Este parâmetro é representado pela equação do tipo: hg =C.t-n, a qual indica que a eficiência térmica na interface metal/molde decai com o tempo. Muitos parâmetros podem influenciar o coeficiente global de transferência de calor (hg), neste estudo, os percentuais de Sn em ligas do sistema Al-Sn são analisados (10,20,30 e 40%Sn). Portanto, o principal objetivo deste estudo é propor uma relação matemática que descreva, para o sistema Al-Sn, a evolução hg em função do teor de Sn. A relação matemática foi obtida através do método dos mínimos quadrados

Aug 17, 2017

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By Chris Larsen, Carole Fortin, Dave Scott, Curtis Deredin, Ian Orford, Jean Guy Gauthier, Andy Trusiak, Lyne Côté, Mike Cooper

"Upon successful commissioning of the Stage Grinding Project (Cormier et. al., 2002), process improvements predicted through pilot plant testing were obtained in several flotation circuits, resulting in higher grades and recoveries for zinc and lead concentrates. Subsequent to establishing new baseline operating conditions from the Stage Grind Project implementation, additional opportunities were identified, and through the application of Six Sigma methodologies further gains were made. Six Sigma improvement projects were carried out in the copper-lead, zinc, lead upgrading and bulk flotation circuits. The overall performance increase resulting from incremental improvement projects has been substantial.Most remarkably, given the operational maturity up to the late 1980’s, the Brunswick concentrator team has continued to deliver a steady stream of major improvements over the past fifteen years. While senior managers and their programs have changed several times, there have been some critical constants over the long run. Common elements have been a commitment to team work, a commitment to recruit and maintain technical personnel, a structured business improvement framework supported organizationally by senior management, and focus on a few priority initiatives rather than trying to fix everything at once.The paper briefly discusses the longer term setting and then endeavors to illustrate, with examples, how improvements are presently achieved by applying the Six Sigma quality program.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s larger lead/zinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 mine. In excess of 100 million tonnes have been milled to date. The concentrator employs differential flotation to produce lead, zinc, copper, and lead/zinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2005

By G. Wozniak, R. Rostanski, H. Pfanz, G. Aschan, E. Sierka

"Industrial wasteland is a typical element of the landscape of all the industrialised regions in Europe. There are many examples from Poland as well as from other European countries that post-industrial sites have been undergone natural colonisation and succession to establish in some cases ecosystems of greater biological diversity than the original ecosystems. The post-industry sites regardless of any reclamation carried out, undergo natural successional processes. The respective biological diversity (number of species, and number of plant assemblages) reflects the micro-variety of the specific habitat. This paper summarizes the results of investigations, which have been carried out since 1989 on coal mine water sedimentation pools in the Upper Silesia Industry Region. The aim of this study is to demonstrate the diversity of spontaneous plant communities recorded on post-industrial waste sites. In the course of the long time fieldwork, plant assemblages representing nine phytosociological groups have been identified."

Jan 1, 2005

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe Minerals Corp.'s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5 m3 (300 cu ft) lead and zinc

Jan 2, 1979

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015