Search Documents

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981

The selective placement of coal strip mine overburden is examined. Physical end chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions of similar problems. Five mining methods already used in the industry, that are capable of selectively handling; waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons arc made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided.

Jan 1, 1981

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercapto silanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1990

By H. Gerry Stephenson, Devin Castendyk

"One of the most important environmental issues associated with contemporary openpit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following:• The water quality within the pit lake, plus surface water and ground water discharging from the pit lake, meets premining or other acceptable water quality conditions of the receiving environment. • The termination of all active treatment processes.• The return of the pit lake to the government for long-term care and maintenance.• The release of the mining company from all future liabilities associated with the pit lake.• The return of the environmental bond to the mining company.• The reuse of the pit lake for some post-closure, beneficial purpose.The achievement of these goals is known as walk away pit lake closure.Peer-reviewed publications of successful walk away, pit lake closure provide mining companies with the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). In North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources (Vandenberg, 2018; Crossman, 2019). The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need to document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry, at large, can learn from these examples and can better address public concerns."

Aug 1, 2019

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016

By John Gross

From the time when man first pounded one rock upon another or used heat and sudden chilling with water to disintegrate rock, the art of crushing advanced but slowly to the mule-driven arrastre and the Chilean mill stage until the advent of power-driven appliances made material progress possible. The combined efforts of manufacturers and operators have made modern machines highly efficient mechanically. Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or the Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere.

Jan 1, 1938

By H. E. Frimmel

Abstract - Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morpho­logical characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively , estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry . Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infiltration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in turn, was deter­ mined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid:rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from recent empirical studies of the relationship between mine safety and characteristics of miners, mine management, and mining companies. The review is based on literature published in the United States during the period from 1976 to 1988. In addition to summarizing the empirical findings, this report discusses the implications and limitations of these studies, and gives recommendations for improving mine safety. An annotated bibliography section appears in the appendix.

Jan 1, 2009

By Xiang Sun

Microwave heating has been used in numerous industrial processes due to its great advantages when compared with conventional heating methods. However, microwave heated products can be affected by non-uniform temperature distribution resulting from the mechanisms of microwave heating. To overcome this problem, a critical step is to have a temperature-time profile. In order to characterize and evaluate microwave heating effects, an accurate temperature measurement is needed. This paper discusses the possibility of applying several temperature measurement techniques in microwave processing. Both contact and non-contact methods are introduced and compared.

Jan 1, 2006

By P. L. Ngwenyama, I. Maubane

Soundless chemical demolition agents (SCDAs) are proving to be the future of sustainable and environmental-friendly mining. These expansive chemicals become critical when there is a need to break rock close to communities, environmentally sensitive areas, and critical structures and infrastructure. Unlike explosives, the SCDAs do not generate air-blast, ground vibrations, flyrock, noise, dust, and noxious fumes, which can negatively affect the environment, surrounding communities, sensitive areas, and critical structures and infrastructure. Over the years, several types of SCDA products have been used successfully in the civil and construction industries for the demolition of old and dilapidated buildings near vibrations and environmentally sensitive areas. They have also been used to fragment boulders in the mining and construction industries. However, to date, no study has investigated the applications of soundless chemical demolition on a large-scale in opencast mines. Therefore, this study evaluated whether soundless chemical demolition can break large volumes of in situ rock. This was done by conducting five trials using Nex-Pand soundless chemical demolition agents in four different surface mining sites. Trial 1 was unsuccessful as it was unable to break the rock due to the large confinement between the drilled holes and the use of a hole diameter that was 182% larger than recommended. Trial 2 was a success as it was able to fracture the rock with a crack width that reached 110 mm after 72 hours. Trial 3 generated cracks at the biggest hole diameter of 102 mm. The cracks developed and ceased to increase after 96 hours at a crack width of 100 mm. Trial 4 achieved the smallest crack width due to a very competent rock compared to the other sites. Trial 5 generated cracks at a slower rate than other trials because of the use of Nex-Pand powder at lower ambient temperatures than recommended. These trials proved that soundless chemical demolition agents can replace explosives in areas closer to sensitive infrastructure and communities. This will ultimately enable mines to unlock value and access deposits in these areas.

Jul 23, 2025

By Gene R. Reid

The contract objective is the development of an Automatic Fire Control System for Mobile Underground Metal Mining Equipment. The Phase I Report, which described the projected data handling plan, was published on July 24, 1975. The Phase II effort covered the period from July 24 through December 2 and accomplished the following objectives: ? Acquisition of data in accordance with the project data handling plan. Data were acquired through visits to twenty mine sites in ten states and Canada; visits to Bureau of Mines and MESA facilities; visits to mobile equipment manufacturers; and an extensive literature search. ? Analysis of accumulated data which provided the following specific types of design inputs: selection of the type of mobile underground equipment found to represent the greatest overall fire hazard; typical operating conditions for the vehicle; characteristics of the reported fire experiences; and performance, cost and maintenance factors affecting potential purchases of automatic fire control systems for underground mining equipment. ? Development of the AFCS design concept. Utilizing the data analysis results and considering the state-of-the-art of fire control system components, a recommended design concept was developed with particular emphasis placed on the need for a low cost and reliable system. Design trade-off studies are provided for the recommended system and for four alternate system concepts.

Jan 1, 1975

1. Domestic Production and Use: In 1983, 12 companies operated 27 primary aluminum reduction plants, with 4 firms accounting for 65% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Maryland, New York, Ohio, and West Virginia 35%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central States 16%. Based on published producer prices, output of primary metal in 1983 was valued at over $5.7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 37% of domestic consumption in 1983, transportation 19%, building 17%, electrical 9%, consumer durables 8%, and other uses 10%.

Jan 1, 1984

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data. Thunderbird is part of the Integrated Mining Systems (IMS) alliance. IMS offers the mining industry the most comprehensive line of monitoring and navigation products available today for mobile mine equipment. In addition to Thunderbird’s drill monitors and GPS systems, the product line includes: Fleet Management Systems for trucks and loaders; dragline and shovel monitors; GPS based navigation systems for shovels, dozers and other mobile equipment; and surveying systems. IMS uses common communication systems, operating systems, and hardware components in order to provide a truly Integrated Mining System.

Jan 1, 2000

By E. D. Gardner

This bulletin, which discusses open-cut mining at the metal mines of the United States, is the last of a series of such papers by the Bureau of Mines describing the principal methods of mining.4 Open-cut mining is applicable to flat-lying mineral deposits relatively near the surface. Vein deposits seldom are amenable to this method, although outcrops of veins sometimes are worked as open pits. Most of the iron ore of the country is mined from open pits; according to the Minerals Yearbook, 67.4 percent was mined from open pits and 32.6 percent from underground mines in 1937. Open-cut mining is relatively new in the copper industry but yields more copper than any other method; in 1937 about 52 percent of the copper ore mined in the United States was taken from open pits. Lead-zinc ore has been produced from open pits in the Joplin (Mo.) district, but most of the deposits in this area, although flat-lying, are too deep to be mined economically by the open-cut method. In 1937 one company at Oronogo, Mo., was stripping overburden and mining mixed oxidized and sulfide ores by this method.

Jan 1, 1941

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007