Search Documents

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By Fiseha Tesfaye, Pekka Taskinen

"Thermodynamics of the equilibrium phase assemblage Ago_9Cul.lS-Cu2-xS-CuS have been studied by an EMF -method. The ternary phase was synthesized from the pure Cu2S and Ag2S in vacuum furnace at high-temperature and mixed with appropriate compositions of Cu2S and CuS to form the cathode electrode. The EMF-measurements were made on the solid-state galvanic cell Pt(-) I Ag I RbAg,ils I Ago9Cu1.1S-Cu2-xS-CuS I Pt(+), in a temperature range from 316 K to 498K.Based on the measured EMF vs. T relations, thermodynamic functions (?fG° , ?fS and ?fH°) of stromeyerite (Ag0.9Cu1.1S) in equilibrium with Cu2-xS and CuS have been determined. The obtained experimental values have been compared with the available literature values. New experimentally determined thermodynamic properties of the solid solution (Ag,Cu)2Sss were determined.IntroductionDue to intense mining of high grade sulfide ore minerals in the past, recently, the available sulfide ores are poor in metals and becoming increasingly complex; such that, the production of high grade metals by the conventional pyrometallurgical processes is compromised. Consequently, smelters are in need to modify their operating flow sheets and strategies for processing more complex feed materials economically, while meeting the strict environmental regulations. To make the appropriate modifications, accurate thermochemical data of phases and phase assemblages which exist in these complex ore minerals are essential.Silver-bearing sulfosalts are encountered in ore minerals for the production of base metals and are common sources of silver. Among the silver-based sulfosalts, stromeyerite (Ag0_9Cu1.1S) is relatively common ore mineral in most hydrothermal vein and replacement deposits [1]. Recently, the ternary chalcogenide compound Ago0.93Cu1,07S has been studied, intensively, due to its high ionic conductivity and gradual disorder in the sequential phase transitions [2]. Therefore, accurate knowledge of the thermodynamic properties of stromeyerite has considerable fundamental and practical interest in many aspects of extractive, chemical and physical metallurgy."

Jan 1, 2014

By M. Pawlik

The rheological properties of mineral suspensions affect the design and operation of transport, mixing, size classification, grinding, gravity concentration, flotation and de-watering systems. In many cases, the rheological properties can be modified to improve processing through the addition of chemical additives. These additives may be either organic or inorganic and generally affect the state of particle aggregation or dispersion. Inorganic modifiers act primarily by affecting the surface charge of mineral particles and thus control the magnitude of electrostatic attraction/repulsion between particles. The action of organic additives (polymers and surfactants) is a combination of electrostatic and steric forces – the latter being related to the molecular weight of these reagents. While low molecular weight polymers are dispersants (viscosity reducers), high molecular weight polymers are likely to induce flocculation and increase yield stress.

Jan 1, 2004

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By R. H. Ring

The Automatic Extraction System (AES) was designed and built under a U.S. Department of Energy Contract by the National Mine Service Company in cooperation with the Lee Engineering Division of Consolidation Coal Company. The Pennsylvania State University, Mining Engineering Section, was contracted as an independent auditor of the AES performance. The AES had a rotating cutter drum like a continuous mining machine; but two hydraulically powered roof supports, four roof-bolting drills, a dust scrubber, a ventilation fan and ducting in the roof supports, semi-automatic control, an extensible chain conveyor, and other innovations led to the distinction "extraction system" as opposed to "miner-bolter" or "continuous mining" machine. After design and assembly, the AES was field tested experimentally in an underground coal mine. The in-mine performance audit was preceded by a computer simulation of the potential production for a later comparison with the actual tonnage mined by the AES. This paper describes the results of an in-mine trial and assesses the production potential of the AES.

Jan 1, 1980

By MAURICE ALTMAYER

M Y DUTIES, as a member of the Department of Franco-American War Cooperation of the French High Commission were to study the copper and brass industries of America from the mining of the various non-ferrous metals to the semi-finished, or finished materials. In the pursuit of these studies, it was my privilege to visit a number of industries and organizations in different parts of the country. I first visited most of the Eastern copper refineries that were supplying the Allies with vast amounts of metal. These works are producing their material by the multiple or the series process, although the first method predominates. But, regardless of the process employed all the plants attain an exceptionally high standard of quality in their production. One of the points that particularly attracted attention was the manner in which improvements could be traced from the older worlds to the more recent ones. The impression was that, thanks to a spirit of broad-minded cooperation between the principals of the companies and frequent exchanges of views between members of the staffs, all persons interested benefitted by the experience thus gained, to the advantage of the community at large.

Jan 1, 1920

By Hernán Chavez, Sandro Ludeña

La minería es un industria muy retadora para lograr su desarrollo, desde la etapa exploratoria, pre factibilidad, factibilidad, construcción y finalmente llegar a operar, en todas estas etapas se presenta el gran reto de generar gran volumen de información, en medio ambiente desde la línea base, ha sido el cuello de botella el homologar y/o organizar una sola base de datos integral, para que estos sean usados para sustentar distintas estudios, la situación social también conlleva a tener un mejor control y aseguramiento de la información, mientras más transparente sea, serás mejor visto ante las comunidades.

Sep 29, 2023

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

By Jason M. Ryan, T Michael LeBlanc, John H. Heiiig

Drill trajectory deviation is a recurring problem in the Mining Industry retreat stoping operations. As a result of this deviation, it is quite concevable that 60 kg (165 mm 0) and 103 kg (203 mm 0) explosive charges are detonated beyond the hanging wall contact. Consequently, there follows a reduction in hanging wall stability and an increase in ore dilution.

Jan 1, 1995

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By L C. Taylor, H U. Lesiste

This paper describes a method for estimating the density distribution in the soil cap as a function of distance from its top at the time of impact with the target. It provides an estimate of the density distribution in the soil on the center line of the soil cap at the time of target impact for a single depth of burial of the charge and two heights of target and shows that, for the heights of target and the depth of burial considered, the thickness of the soil cap first increases from the in situ value and then decreases. The distribution of soil density along the centerline of the soil cap changes significantly with distance from its original position. These results can be used for validating hydro-code computations and the soil models used in the computations.

Jan 1, 2011

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023

Jan 1, 1970

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009