Search Documents

ABSTRACTRock stresses can be modified by physicochemical processes.If rock pores allow the ingress of water and oxygen, but are not large enough to permit the exit of larger molecules of weathering products, anomalous rock pressures develop. Rock masses may also be subjected to osmotic pressures developed as water diffuses into pores and joints filled with saline water. Anomalous rock pressures may also develop as gels filling pores undergo syneresis and as salts crystallize from pore solutions.

Jan 1, 1968

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By David R. Lentz

Abstract -At True Hill in southwestern New Brunswick, low-grade porphyry-style Bi-Sn-Mo greisen mineralization is associated with the cupola of an epizonal granite porphyry (granite) that also exhibits three episodes of brecciation. The first episode of brecciation is an in situ, 8 m to 10 m wide transitional zone of net-veined to coarse-grained "blocky" endogranitic mesobreccia that is chloritized and greisenized and hosts weak disseminated mineralization. ln a zone doser to the host rock­ granite contact, angular fine- to coarse-grained endogranitic mesobreccia with greisenized matrix is superimposed on the earlier transitional breccia. The latest episode is fault-controlled and consists of quartz- and chalcedony-hosted subangular to rounded fine-grained "pebble" mesobreccias that crosscut and brecciate the other breccia types, as well as the adjacent altered metasedimentary country rocks. The first two episodes of brecciation are magrnatic-hydrothermal in origin related to hydrofracturing of the granite carapace and are accompanied by greisenization and mineralization, whereas the post-mineralization, silica-hosted, "pebble" mesobreccias related to hydromagrnatic, low­ temperature fluid circulation and/or boiling along faults near the contact. These magmatic­ hydrothermal and hydromagmatic mesobreccias are similar to those associated with W-Mo-Bi porphyry-greisen mineralization at the Mount Pleasant deposit.

Jan 1, 1994

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By H. Lawson

The Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03in April of 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib, and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB 09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2012

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

To the industrial geologist, as wen as to the general or historic geologist, the possession of a reliable key to the true order or sequence of the stratigraphy or position of the various upper rocky envelopes of the earth's crust, is, equally, a desideratum of the utmost importance. Of similar value to the two groups of students is the possession of facts which throw light upon the relationships which subsist between the puccessive rock formation of different countries, especially between countries lying close to each other, or within the same great geographical division.But there is necessarily a fundamental distinction which marks the respective limits of the field of observations of the industrial geologist, and the purely historic interest of the general geologist. The former has a more definite though less extensive scope. The scope of the latter is wide and indeterminate. In short, the observations of the industrial geologist are, 'from a commercial or economic point of view, of a more practical character, and are, therefore, intentionally restricted to the study of all geological questions which throw light upon the rocks which yield products of economic value and only include the study of the character and history of other rocks, in so far, as they afford aid to the more perfect comprehension of the best manner in which materials of economic value are likely to be sought, and the best means whereby these products may be secured for the material advantage of the community. The motive of the general geologist-in most cases-is a love of the study of some particular branch or province of the geological field, and the fascination of opening a new volume in nature's library, and the hope of extending the realm of knowledge, however slight, are often sufficient, as a motive, to enlist the energy and life's devotion of the true brethren of the hammer, irrespective of considerations regarding the commercial utility of the pursuit.

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau's mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By Gang Yang, Manchao He, Chengzhang Gao, Jun Zhang, Yayun Li, Jun Yang, Shilin Hou, Ben Liu, Yajun Wang, Jianning Liu

To explore the mechanism of roof directional breaking in gob-side entry formed automatically without coal pillars, the numerical simulation was used to study the deformation movement of roof, the deformation evolution of roadway, and the stress distribution of roadway under roof directional breaking and non-roof directional breaking. Based on the results, the deformation movement of roof is divided into three stages: the goaf roof collapse stage, the basic roof deformation stage, and the basic roof stability stage. The goaf is filled with gangue due to the broken expansion characteristics of the collapsed rock under the roof directional breaking. Due to the supporting force of gangue, the deformation of the basic roof under the roof directional breaking is smaller than that under the non-roof directional breaking, which reduces the influence of the deformation of the basic roof on the deformation of the roadway roof and improves the integrity of the roadway. At the same time, roof directional breaking cuts off the stress transfer path of partial roof, which weakens the peak stress convergence on the arc side, transfers the peak stress convergence to deeper, and improves the stability of roadway. Finally, a field test was carried out to further verify the accuracy of the numerical simulation. The field test results are in good agreement with the numerical simulation results. The roadway deformation is small and meets the requirements of safety production. It is proved that roof directional breaking plays a positive role in improving the stability of the roadway.

Dec 22, 2022

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994