Search Documents

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By Marcos Campos Silveira

A Unidade Niquelândia da Votorantim Metais possui 9 fornos multi andares usados para a redução de minérios lateríticos com o uso de monóxido de carbono e hidrogênio como agentes redutores. Cada forno possui 10 câmaras de combustão para geração destes gases que trabalham em contra-corrente com o minério alimentado pelo topo do forno. Já utilizado como combustível óleo A2 incorporado ao minério bem como sua combustão em câmaras. O trabalho consiste na substituição do óleo por uma emulsão de combustíveis líquidos e sólidos a fim de flexibilizar a matriz energética e promover redução do cash cost sem queda na eficiência operacional. A utilização industrial da emulsão teve início em 2006 através da sua incorporação ao minério alimentado na proporção de 19% de coque de petróleo e 81% de óleo A2 em poder calorífico e em 2014 esta mistura alcançou a proporção de 39% de coque e 61% de óleo A1. Em paralelo e após testes de combustão em planta piloto, foram realizados testes industriais de queima também nas câmaras de combustão em dezembro de 2012. Com o bom desempenho, em dezembro de 2013, 14 das 90 câmaras já estavam nesta condição com previsão de 20 câmaras até junho de 2014 otimizando a capacidade da estação de óleo+coque. Com isto a substituição (%) global dos fornos em poder calorífico avançou de 6,38% em 2011 para 16,12% em 2014 acumulados até abril. Com uma nova estação existe a possibilidade de operar 90 câmaras nesta condição e chegar a um valor de 39% de substituição global.

Jul 31, 2018

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

Samples of a refractory copper ore were examined to test their response to segregation roasting, flotation, and acetonitrile leaching. Recoveries in the segregation roasting stage were between 60 and 100 per cent, while flotation recoveries varied between 60 and 85 per cent in cleaner concentrates assaying 25-40 per cent copper.The fraction of the copper which could be leached from the concentrate by an acetonitrile/sulphuric acid/cupric ion leach solution varied from 16 to 97 per cent, the lower recoveries being correlated with the presence of sulphide in the concentrate.

Jan 1, 1973

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (&lt;1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058&#176;C).

Jan 1, 1972

By J. Ran

There are challenges in mining deep tabular ore deposits using the open stoping method, particularly mining remnant panels towards the end of mine life. The remnant panels have experienced stress concentration and are in the failing or post failure state causing drilling and loading difficulties, ground movement, induced seismicity and ground instability problems. As more mines are going deep, without effective ground control management, the mine production will be interrupted and equipment damage and personnel injury are likely to occur. Mining at Falconbridge Lockerby Mine located in the Sudbury Basin was concentrated in the deep zone from late 1990s to 2004. The remnant panels situated approximately from 1800m to 1920m below surface were mined in 2004 before the mine closure. These panels were in the central section of the orebody along strike. The orebody was relatively narrow ranging from 5m to 15m and steep dipping at 70o to 80o. Because of the retreat mining sequence and the mining depth, stress concentration, wall closure and seismicity had caused a number of mining difficulties. Managing these challenges was critical in achieving the mine production target without compromising personnel safety and excavation stability. A comprehensive ground control management approach was adopted to mine the remnant panels at depth. The measures taken included ground movement monitoring, understanding the movement pattern of the footwall rock and selecting appropriate support systems, analyzing seismic monitoring data and defining re-entry protocol, brow support design and restricting access. This paper presents these ground control measures and the experience gained in successfully mining the deep remnant panels at Lockerby Mine.

Apr 1, 2005

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 120 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257; 7267,`7273; 7285, 7292, 7303, 7310, and 7324. 1. GRAVITATIONAL METHODS 7933. Ansel, E. A Eine Untersuchung zum Problem der Isostasie (An Investigation Regarding the Problem of Isostasy). Gerlands Beitr. Geophys., Leipzig, vol. 59, 1942, pp. 16-26.

Jan 1, 1945

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

The National Mining Hall of Fame and Museum (NMHF&M) will induct its the 2014 National Mining Hall of Fame Class on Sept. 13, 2014 during its 27th Annual Induction Banquet and Ceremony at the Westin Hotel in Denver, CO. Representing the domestic and worldwide metal production, education, and health and safety sectors of the industry, this year?s four inductees cover a diverse cross-section of the mining industry. Harry M. Conger III, Günther Franz (Frank) Joklik, Ellen Swallow Richards and Dr. Alfred Weiss will join 223 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame. They were selected for being visionaries, leaders and ambassadors, both within their own sectors and across the industry at large. Conger was a great role model and strong advocate within Homestake Mining Co. and among his industry peers on behalf of environmentally responsible, safe, profitable and high-performance operations. As chairman and chief executive officer, Conger was instrumental in revitalizing and rebuilding Homestake into an industry leader in technological advances and environmental protection. Through his contributions in exploration, project development and operations management as Kennecott president and chief executive, Joklik did much to strengthen Kennecott as a company and assisted in restoring the competitiveness of the U.S. mining industry. Richards is generally recognized as the founder of ecology. She was the very definition of a pioneer in such diverse fields as chemistry, geology and mineralogy, mining and metallurgy, environmental science, public health, home economics and education. Weiss was a true visionary in using quantitative methods and digital computers to aid mineral exploration, plan and design mines, operate mineral production facilities and integrate the disparate information resources throughout a mining company into a modern management information system. NMHF&M Board of Directors Chairman, Paul C. Jones, said, ?Again this year we are honored to be able to induct an outstanding group of deserving individuals who have made exceptional contributions to the mining industry in the United States. Included are two living inductees who have made significant contributions to management in the industry. One inductee was the first female graduate from the Massachusetts Institute of Technology, its first female faculty member and the first female member of AIME who had an outstanding career as a mineral investigator in the United States. Another inductee was a lifetime innovator in bringing digital technology into common use in our industry. Each of our 2014 inductees made significant and lasting contributions to our industry and are well deserving of becoming a member of the National Mining Hall of Fame.? The Hall of Fame Induction Banquet and Ceremony is a marquee event for the National Mining Hall of Fame and Museum each year. The 27th Annual Induction Ceremony and Banquet will be held at the Westin Hotel in Denver, CO on Saturday, Sept. 13, 2014. For banquet reservations, contact the NMHF&M office at 719-486-1229. More information is available on the NMHF&M website at www.mininghalloffame.org.

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By Tad S. Golosinski, R. Larry Grayson

Online education is not new. During the last decade, it has reached the stage where many universities offer a variety of courses, degrees and programs without any associated residency requirements. The most successful of the online universities, University of Phoenix, offers hundreds of accredited programs for close to 100,000 students throughout the world (www.phoenix.edu). Online education is considered to be a valid equivalent to traditional, classroom-based education. It is best suited to the needs of mature students with full-time jobs and a desire to deepen their knowledge. While most of the e-business has experienced severe setbacks during the last two years, e-education shows no signs of slowing down. On the contrary, the number of students and institutions offering online education keeps growing. The value of e-education associated expenditures was expected to reach $300 billion in 2001 (Sanoff,2001), making it a serious and mature industry.

Jan 1, 2002

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015