Search Documents

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By Steven E. Mischler, Jay F. Colinet

The study analyzes the impact of the Continuous Personal Dust Monitor (CPDM) on reducing overexposures to coal mine dust. It compares compliance sampling data before and after the implementation of the CPDM and the 2014 MSHA dust rule. The results indicate a significant reduction in the percentage of samples exceeding the dust standard for various mining occupations, highlighting the effectiveness of the CPDM in improving miners’ health and safety.

Feb 22, 2022

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

By John H. Hollomon

A REVIEW of the steps which have been made to increase knowledge in the field of ferrous physical metallurgy during the closing period of World War II brings both pleasure and disappointment. Contributions of great value have been made, to be sure. However, due partly to the stress of the times, researchers in this field have been in the main directing their attention toward the short-range problems involved in the development and production of materiel for war. Furthermore, publication of the results of a great number of studies has had to be delayed. Much of the German work may, indeed, be lost entirely, owing to the efficiency of our bombers, which managed to account for most of the famous Kaiser Wilhelm Institut of Dusseldorf, not to mention the other large laboratories and manufacturing plants throughout that country. It would seem safe to assume, however, that fundamental research in Germany had been forced to give way to the shallow, but more pressing, engineering problems of a country trying to avoid defeat. In Russia the picture has been clouded by the limitations imposed upon comunication; but this much does seem clear: Russia alone among the great nations of the world has maintained her long-range view and has continued to foster research of the most fundamental type. English workers; on the other hand, appear to have been able only to meet the demands of the pressing problems of war, and their studies have been of the short-range variety. That metallurgical research of any sort should have continued in France during this chaotic period in her history would seem impossible, but, amazingly, a small handful of scientists did manage to carry on their work, and it is to be hoped that more will be heard from them in the future.

Jan 1, 1946

In preparing this paper, the writer hopes to achieve two main objects. Firstly, an indication of the desirable features of coke from the viewpoint of a blast furnace operator should be of assistance and value to those connected with coal and coke research, coal mining, the manufacture of coke and the production of iron. Secondly, it is hoped that the conclusions and opinions expressed herein, which are known to be of a controversial nature, will promote some discussion and thought. In this way, other workers may see fit to contribute and enlarge our general knowledge of Australian coke and its behaviour in blast furnaces.Those properties of coke that are considered to be of importance to blast furnace operation will be examined. Although broadly speaking, the composition and characteristics of coke are inherent in the coals used, any special features of coal preparation and carbonization that affect the resultant coke will be discussed. An attempt will also be made to indicate the effect on blast furnace operation of significant irregularities in these properties.THE FUNCTION OF COKE IN A BLAST FURNACECoke has four important functions in a blast furnace:1. To reduce the oxides of iron and other elements to metal and to provide the carbon absorbed by the iron.2. To supply the necessary heat for the process.3. To provide an open supporting structure in which the descending ore and limestone lie exposed to the action of the ascending gas.4. To provide voidage in the bottom of the furnace, so that iron and slag can accumulate in the hearth.

Jan 1, 1957

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By Francisco Anglade

Dado que la simulación digital es una herramienta auxilar para los ingenieros de procesos -en tanto evalúa la factibilidad de un flowsheet propuesto y predice el efecto de una modificación para un flowsheet existente, su importancia también se extiende también a la evaluación de alternativas para las estrategias de control en los circuitos de la planta. En ese sentido, el presente trabajo señala los beneficios económicos y técnicos obtenidos en la planta San Rafael mediante el empleo de simuladores en los circuitos de molienda, chancado y concentración gravimétrica, los cuales permiten corroborar los cambios efectuados u optimizar los circuitos señalados de forma simple y rápida.

Sep 9, 2007

By Pascual Perazzo Vaschetti Gabriella

The increasing emphasis on environmental issues has crucial importance in mining projects, hence in tailings dams. Their water barrier needs a two-fold environmental assessment: the environmental impact caused by construction activities, and the environmental impact over time. Unfortunately, tailings dams’ failures have great and long-lasting environmental consequences, and as mining sites become bigger and tailings dams higher, the risk of failures may increase. Furthermore, since these dams are mostly constructed over many years, design parameters/materials may change, the engineers may change, and since cost is a driving parameter, less attention may be given to quality control and monitoring. Geomembrane water barriers mitigate such impacts.

Sep 30, 2022

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By A B. Christie

Known epithermal deposits in the Coromandel region belong to the low-sulphidation type, represented by three subtypes: (1) andesite-hosted epithermal Au-Ag, (2) rhyolite-hosted epithermal Au-Ag, and (3) andesite-hosted polymetallic veins. Paleo-depths for a range ofdeposits are estimated using various features including: paleo-surface indicators (e.g. sinters), hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and alteration mineralogy. Paleo-depth estimates to the base of the ore zone for the rhyolite-hosted Coromandel deposits are in the range 200 to 500 m. Andesite-hosted Au-Ag deposits have more variable paleo-depths, and are deeper (up to 950 m) in those deposits with base metals at depth. The majority of Coromandel Au-Ag deposits have limited depth extents (<200 m) of economic grade mineralisation, although Waihi and Karangahake are notable exceptions with depth extents of 575 m and 700 m respectively. Limited depth extents of economic ore are a feature of epithermal systems worldwide and are commonly attributed to gold deposition from boiling fluids. Under hydrostatic conditions in epithermal/geothermal systems, boiling in an up-flowing hydrothermal fluid is controlled by the boiling point for depth (BPD) curve. From fluid inclusion studies of many low-sulphidation epithermal systems, deposition of electrum in economic concentrations appears to be confined to a temperature window of 260 to 180¦C. This means that for dilute, gas-poor fluids that follow the BPD curve, gold deposition is limited to a vertical depth zone of about 400 m, with its upper boundary at about 100 m below the ground surface. The greater depth extent at Waihi and Karangahake, can be explained by mixing of/a deep, hot (300¦C) fluid with cooler (c. 200¦C) heated ground waters. This has the effect of lowering the 260¦C isotherm by up to 300 m, thereby increasing the depth range of economic grade gold deposition within the 260 to 180¦Cwindow of electrum deposition.

Jan 1, 2000

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011