Search Documents

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By R. C. D. Phillis

The annual mine planning process is one of the most important tactical/operational steps towards achieving strategic goals. These tactical plans are part of a very comprehensive Mineral Resource Management process, with the natural sequel to planning being execution. The execution of an underground hard rock mine plan is a multi-project environment that comprises many development-construction-equipping-stoping single project paths, which are referred to as ?stoping paths?. The uncertainty that typifies execution of projects comes in the form of untimely disruptions to constituent tasks and/or project paths. Annual mining plans also include quantified objectives for occupational health and safety, production, quality, cost, employee morale, environment, and corporate social investment. Such objectives make for a highly complex environment that management must contend with?complex in the sense that all the paths and objectives have interdependent constraints. Furthermore, at the time of this paper, Sections54*and 55**of the MHSA*** put the onus on management to ensure legislative adherence. It stands to reason that planning estimates allow excess capacity?buffers?that cushions the impact of untimely disruptions. This paper concerns the fact that despite all the buffers allowed for, time, scope, and budget creeps impact on mine planning and threaten its successful execution. As a consequence, the paper deals with buffer management, the essence of Critical Chain Project Management (CCPM). Effective buffer management provided strategic (executive level) updates without losing the tactical/operational detail necessary for job card creation, especially where professional skills and experience are in short supply. Indicative bottom-line results showed CCPM to be highly effective.

Jan 1, 2011

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By Herbert H. Einstein

The innate variability of natural materials and processes causes uncertainty in the models representing the natural phenomena and uncertainty in estimating the parameters that are used in these models. Reliability analyses, in contrast to the traditional factor of safety approach, are well suited to a rational incorporation of uncertainty in design and exploration decisions. Probabilistic kinetic and kinematic analyses were developed and combined to form reliability analysis methods. With one method the reliability, i.e.) the probability of failure, of an individual 2-plane wedge in a slope can be determined. The other method is aimed at slopes with a single slope parallel set of joints. In each case two approaches were developed, an encompassing one relying on computer codes and a simplified or summary approach relying on charts or pocket calculator computation. A major contribution of these approaches is the treatment of joint persistance. Instead of having to assume a certain persistence, it is now possible to use exploration data on joint geometry and to include the persistence effect rigorously.

Jan 1, 1979

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

By Michael F. Dunn

Since crushing of rock to a smaller size is an integral part of almost any mining and quarrying operation, a study was carried out to identify and develop improved techniques for alleviating a major cause of accidents and work stoppages arising when an oversize luck or boulder lodges in the throat of the crusher. The configurations and operations of various crusher types is described, sources of boulders in the mining operation, and a detailed review is made of mining, quarrying, and construction regulations for all states, Canada, and the Federal Government for applicable provisions. Representative mines were visited and other operations contacted for their boulder handling techniques where it was found that blasting techniques used included mudcapping, bombs, and blockholing, often done very crudely and inefficiently with poor practices and various mechanical systems were used such is hooks of, overhead cranes, impact hammers, and grapplers. Safety analyses of all methods pointed out the hazards associated with blasting in the open and the dangers of entering a crusher. Boulder blasting can be done in a safer fashion if a planned step-by-step procedure is followed, and inherently safer blasting products such as exploding bridge wire blasting caps and improved blockholing techniques. In general, though, the installation of a suitable mechanical system such as an impact breaker will prove safer and cost effective even in a smaller mine or quarry.

Jan 1, 1981

This is a most interesting paper and some data in it are corroborated by work I did at Watertown Arsenal some time ago with iron powder. I would like to ask Dr. Wulff to say just a little more about the compressive and tensile stresses on the surface of compacts. JOHN WULFF (author's reply).-Our work has not yet been completed; although enough data have been obtained with cylindrical compacts of iron to permit some conclusions. Briefly, in a compact 3/4 in. high and 1/2 in. in diameter pressed at 48 tons per sq. in., the residual stresses on the surface measured by X-ray diffraction techniques are as follows: The radial stresses on top center and bottom of compacts are practically zero; the longitudinal residual stresses on the side walls are near the top quarter of the compact about seven tenths that of the yield point of mild steel in tension; at the center surface of the compact they are in compression and in magnitude about 0.3 that of mild steel in tension; near the bottom, they are practically zero. F. V. LENEL.?- I was particularly interested in the work that Messrs. Wulff and Seelig reported on the influence of lubrication on the density of parts. In connection with the work of the American Society for Testing Materials on determining the green density of a compact, we ran into considerable difficulty in getting reproducible results of green density determinations. It was much easier to get a reproducible green density when the lubricant was mixed with the powder than when the lubricant was applied to the die walls; particularly when the die was not perfect-i.e., if it was somewhat rough or out of round. In this case, it was almost impossible to get reproducible green densities when the die walls were lubricated, while it was not too difficult to get reproducible

Jan 1, 1946

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By Wayne Phillips, Anatalia Silva, Robert Henderson, Tondo. Luis

"Kinross’ Paracatu Mine has 20 years of operational success as one of the lowest grade milloperated gold mines in the world. At year end 2005, Paracatu’s Proven and Probable Reserves were 1.18 billion tonnes at a grade of 0.40 g/t Au, containing a total of 15.2 million ounces of gold.In 2005, the plant processed 17 Mt of ore and produced 180,519 ounces of gold at a cash cost of US$274/oz. An investment of US$470 million has been approved to expand production to 61 Mtpa in 2009 which will extend mine life to 2036. During the period from 2009 to 2013 the project is expected to produce an average annual output of approximately 557,000 ounces of gold at an average cost of sales of approximately $230 per ounce.The soft, friable ore containing readily leachable gold associated with sulphides lends itself to simple processing. The process flowsheet consists of crushing, grinding, gravity recovery, flotation, concentrate leach and carbon adsorption to produce bullion bars. This paper describes the current operation, the deposit’s unique metallurgical features and the future expansion plant that has been designed to optimise recovery of gold.INTRODUCTIONRio Paracatu Mineração (RPM), a wholly owned subsidiary of Kinross Gold Corporation, operates the Paracatu mine. The mine is located in Brazil, 230 km south west of Brasilia in the north west portion of the State of Minas Gerais. The city of Paracatu, which has a population of 83,000 people, is just 2 km south of the mine."

Jan 1, 2007

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

Underground mine designs typically try to avoid extraction beneath streams and rivers of any significant size, especially when the overburden rock thickness between the stream bed and the mine is thin. Potential issues with mining beneath streams include excessive groundwater inflow to the mine; weak ground (roof, floor, and pillar) conditions; horizontal stress effects; as well as stream loss and other potential adverse environmental effects. However, there are times when crossing beneath a stream or river is necessary to move into a new area of mineral reserve without creating additional mine access points from the ground surface. Often, stream crossings are completed without thorough assessment, potentially resulting in increased costs, decreased safety, and, in some cases, failure to advance the mine. Selection of the most favorable location(s) to cross the stream must account for numerous factors and the associated assessment often requires a multidisciplinary approach. Stream crossing investigations often require geological, hydrogeological, geotechnical, and geophysical expertise. Phases of stream crossing investigations include desktop evaluation of maps and aerial photography, stream bed observations, drilling, detailed rock core logging, downhole geophysical surveying, hydraulic conductivity testing (packer testing), geotechnical laboratory testing, assessment, and reporting. The deliverables from a stream crossing assessment typically include geological, geotechnical, and hydrogeological characterization of potential stream crossing locations; classification of favorable and unfavorable crossing locations; recommendations for entry design and pillar sizing; and recommendations for if, and how, to conduct pre-grouting activities. Examples of technical aspects of data collection and assessment are provided based on decades of industry experience conducting stream crossing assessments in various underground mining scenarios.

Jul 28, 2020

By J. F. T. Agapito

Experience at Energy West Mines in the Wasatch Plateau Coal Field, Utah, has shown that longwall face bursts occur mostly near the tailgate when extracting the third adjacent longwall in a panel section where depths exceed 610 m (2000 ft). It is believed that this is due to a combination of cover depth and side abutment stresses created by the widening of a pressure arch formed by interlocking and bridging of large blocks of" very competent strata. The 60-m-thick (200 ft) Castlegate Sandstone probably plays a key role in pressure arching. This paper presents a back-analysis of the location and magnitude of the stresses associated with face bursts that occurred when mining the 7th Right Longwall at the Deer Creek Mine. Improvement of these conditions may be achieved by widening the longwalls to attain critical subsidence width sooner while mining the second long-wall, and to reduce stresses at the face. Wider longwall faces, however, increase the chance of sandstone channel interception often associated with bursts. Satisfactory mitigation of face bursts beyond cover depths of 610 to 670 m (2000 to 2200 ft) may be difficult without using destressing techniques. The hydraulic fracturing/liquid infusion technique seems to offer the best possibilities for application in longwall mining.

Jan 1, 1997

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Herbert J. French

ALLOY steels have become essential to industry in meeting the rigid requirements on materials imposed by our, advanced technology. In comparison with the total ingot capacity of the steel industry, the volume of alloy steels is relatively small although for many years annual alloy-ingot tonnage has, been in seven figures. However, the monetary value of the alloy-steel production is exceedingly high and the benefits derived from the products are relatively great. The trend in total ingot production since 1932 has been generally upward with only two major interruptions. That of the year 1938 was due to a decrease in general business activity whereas that of 1946 resulted largely from work stoppages. Traditionally, the tonnage of alloy-steel ingots produced was in the neighborhood of 5 to

Jan 1, 1948

By Shawna Munn, Nadir Ansari, Toben Jerry

With ever increasing demands on space in urban environments and smaller available footprints, buildings are being designed to increasing heights to meet the need. This case study discusses the increasing challenges in developing projects within urban environments with smaller available footprints and increasing building heights. The One, Canada’s tallest residential building under construction will stand at 85 storeys and is located at one of the most prominent and built up intersections in Toronto, Yonge Street and Bloor Street. This led to many challenges in design and construction of the shoring and foundation work, including the required design capacity of the foundations for the supertall building and proximity of the large diameter drilled shafts to the excavation shoring wall. This case history describes the shoring design option evaluation, performance, and lessons learned to date throughout construction of the building foundations within a small congested site. PROJECT OVERVIEW The One, Canada’s tallest residential building under construction by Mizrahi Developments, is a supertall building that will stand at 85 storeys and 306 m (1005 ft). The first 18 floors will be comprised of retail, restaurants, and hotel with luxury residential condominium units in the tower above. The project is located on the Southwest corner of Yonge Street and Bloor Street, one of the most prominent and built up intersections in Toronto. The L-shaped excavation measures 58 m by 47 m (190 ft to 154 ft) and ranges from 22 m to 28 m (72 ft to 92 ft) in depth with one internal corner projecting 11 m (36 ft) into the site.

Jan 1, 2019

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972