Search Documents

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War I1 has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By Z. Hou

ABSTRACT: Short-term strength, damage and healing boundaries for rock salt are experimentally determined and integrated into the Hou/Lux-MDS damage-healing model. This model can be used to describe the mechanical behaviour of rock salt during a damaging process (under high stress to strength ratios) as well as during a healing process (under very low stress to strength ratios with high confining pressure). The development of the damage and the stress to strength ratio in the excavation damaged zone (EDZ) of a storage cavern under a minimum internal pressure as well as the development of the healing of damage and the stress to strength ratio under a subsequent maximum internal pressure are investigated project-related. The results of the investigation make it possible to shift the permissible minimum pressure boundary down, allowing the optimisation of decisive economic characteristics of storage caverns. RÉSUMÉ: Le comportement court terme, l’endommagement et les conditions de colmatage pour le sel gemme ont été étudiés expérimentalement et intégrés dans le model endommagement-colmatage Hou/Lux-MDS. Ce modèle permet de décrire le comportement mécanique de sel gemme pendant le processus d’endommagement (sous fort rapport contrainte-résistance) et le comportement du processus de colmatage sous très faible rapport contrainte-résistance avec forte pression de confinement. Le développement d’endommagement et le rapport de contrainte-résistance dans une zone d’endommagée (EDZ) d’une cavité de stockage avec un maximum de pression de soutènement ont été étudiés. Les résultats de cette étude permettent de conclure qu’il est possible de baisser la pression de soutènement, et par conséquent d’optimiser les caractéristiques économiques décisives des cavité de stockage. ZUSAMENFASSUNG: Für Steinsalz werden Festigkeits-, Schädigungs- und Verheilungsgrenze experimentell ermittelt und in das Schädigungs-Verheilungs-Modell Hou/Lux-MDS integriert. Damit kann das mechanische Verhalten von Steinsalz sowohl bei einem Schädigungsprozess (mit hohen Ausnutzungsgraden) wie auch bei einem Verheilungsprozess (mit niedrigen Ausnutzungsgraden) beschrieben werden. Projektbezogen werden die Schädigungs- und Ausnutzungsgradentwicklung in der Auflockerungszone einer Speicherkaverne unter einem minimalen Innendruck sowie die Verheilungs- und Ausnutzungsgradentwicklung unter einem anschließenden maximalen Innendruck untersucht. Die Untersuchungsergebnisse erlauben, die zulässige Minimaldruckgrenze nach unten zu verschieben, so dass entscheidende wirtschaftliche Kenngrößen von Speicherkavernen optimiert werden können.

Jan 1, 2003

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By Joseph M. Pugliese

The Bureau of Mines through its contract research program recently analyzed the mining and environmental requirements in the premining stage for copper mining in the northern highland of Wisconsin. The Critical-Path-Method (CPM) was used in this research. However, a step-by-step derivation of the CPM Diagram was beyond the scope of this effort. The Bureau of Mines objective now is to show, step by step, how the original hand-computed CPM Diagram was constructed. The streamlining (restructuring) of this diagram from the original effort is also summarized. The critical path time (longest time) through the original CPM Diagram was 25.12 yr, excluding public liaison effort. This diagram showed the involvement of the regulatory agency, mining applicant and public in the premining stage. Analysis of this diagram produced a streamlined version which reduced the critical path time by nearly 7 yr. The CPM construction methodology offered here may be applied to mine planning for any mining operation.

Jan 1, 1983

By AIME AIME

The American Society of Mechanical Engineers.-The semi-annual meeting of the American Society of Mechanical Engineers will be held in Detroit, Mich., June 23-26. A session will be devoted to hoisting- and conveying-machinery; and many other subjects will be treated in professional papers, among which are . Clutches (with special reference to automobile clutches); The Thermal Properties of Superheated Steam; The Horse-Power, Friction-Losses, and Efficiency of Gas- and Oil-Engines; A Journal-Friction Measuring-Machine; A Simple Method of Checking Conical Pistons for Stress, and The By-Product Coke-Oven. The usual receptions will be held and excursions will be made to manufacturing plants, the slip-building yards, and various points of interest in and around Detroit. Among the excursions' planned is one to the University of Michigan at Ann Arbor. The Gas-Power Section of the Society will hold a session, and the Society for the Promotion of Engineering Education and the Society of Automobile Engineers will hold meet-

Jan 5, 1908

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By I. W. Farmer

Weightings and water inflows into longwall workings often occur together, giving rise to discussions on their relative genesis. Case histories are introduced which indicate that most water inflows are associated with heavy weightings. Resultant large releases of energy can lead to extensive vertical fractures, which can drain water from aquifers or other sources, such as separation accumulations, onto the face. Effectively control of water inflows in these cases depends on face support and weighting control.

Jan 1, 1996

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016

Slope stability is a fundamental part of a successful mining operation. It impacts directly on the safety of personnel and the economics of the mine. The Jwaneng Mine in Botswana is planning a push back of 644m depth in the south east wall. Mining will commence in 2010 and be completed in 2024. This will put the mine in the deep pit category. The mine has invested in extensive geotechnical data gathering and design programs that started as far back as 2003 for the south east wall. The south east wail of Jwaneng Mine is characterized by foliation that dips adversely into the mining faces. The orienta1ion of the foliation is variable due to intense tectonic movements that have also caused the occurrence of faults that are sub-vertical. A considerable amount of information on the characteristics of structural patterns and the rock mass has been collected. This paper presents an overview of the feasibility level geotechnical design that is about to be concluded.

Jan 1, 2010

By Art Cooper

Granulation systems are common in the metals industry. The process of granulating slags, mattes and metals is more than a century old, and a number of different systems have been developed to accomplish this task. These systems have followed an evolutionary path, and may be characterized by common elements in terms of molten material handling, granulation methods and post-granulation processing. This paper will summarize the more common systems used in the metals industry, with particular reference to non-ferrous applications.

Jan 1, 2006

By Manuel Gomez

This report presents prediction equations for 12 variables that are indicative of metallurgical coal quality. The variables include six for coke strength and six for carbonization product yields. All variables were predicted for coking coals having volatile matter contents from 16.3 to 42.1 percent, dry basis. The prediction equations, developed by mathematical-statistical techniques, were based on information from the proximate and ultimate analyses, the size consist, and the petrographic composition of bituminous coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000° C. The equations were evaluated for validity with independent data derived from the 900° C carbonization of 33 binary blends of various coals and 22 binary blends of Pocahontas No. 3 low-volatile bituminous coal with 11 high-volatile bituminous coals. Results show that metallurgical coal quality can be predicted ahead of mining because data used to derive the prediction equations can be obtained at the time of exploration. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques and thus lead to the production of uniform coke.

Jan 1, 1970

By A. D. Prokop, J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated long-wall test facility located at the Pittsburgh Research Center. Sound levels were recorded every 1.5 m [5 fl] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 MA attenuation was attained upwind of the headgate drum.

Feb 24, 1997

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982