Search Documents

Jan 1, 1992

The hematite deposits of Quadrilßtero Ferrffero (QF) are hosted by the Proterozoic itabirites of the Itabira iron formation (Harder and Chamberlin, 1915). These deposits are widely distributed at QF and include the hard hematite ore bodies. However, considerable variations in ore structure and texture can be observed. A preserved banding and lamination in the thin bedded, compact hematite ore, apparently reflects the original layering and/or the prominent foliation of the partly or completely replaced itabirite. The structure of the hematite ore deposits varies from almond shaped, rootless, to bedded bodies, both concordant with the main foliation, and to mesoscopic veins and irregular bodies. Hematite ore textures, which depends on the structural characteristics of the deposit, may be grouped into four main types:thin bedded, laminated and banded; micaceous, foliated and schistose; brecciated; and compact/massive. Thin bedded ores occur in the western, central and subordinately eastern portions of QF, while submicaceous, micaceous and schistose ores are predominant at the eastern part. Brecciated ores exist mainly at the western part and subordinately in central QF. Structureless, compact hematite ores may be either related to the brecciated hematite or occur as isolated bodies at central QF. It is suggested that a synkinematic, acid and oxidant, metasomatism during metamorphism, under a ductile regime, was responsible for the hard hematite ores of the types 1 and 2, and a static, subsequent, hydrothermal, regional metasomatism, under brittle regime resulted in the formation of the types 3 and 4. The common texture present in the all ores is the ubiquitous magnetite porphyroclasts replacement by hematite. Quartz and other silicate minerals are also substituted by hematite. Muscovite, tourmaline, talc, chlorite, apatite and kaolinite have been recognised in the hard hematitic ores. Apparently that mineral association denotes different equilibrium conditions of formation.

Jan 1, 2002

By D M. Aranha, M A. Fonseca, M Echtern

The regional syndeformational metamorphism affecting the Itabira Iron Formation (IIF) at Quadrilßtero Ferrffero (QF) was formerly discussed by Dorr (1965), who proposed that quartz grain size could monitor the metamorphism, according to James (1955), and that the formation of haematite could be the result of the synchronous metasomatic process. Herz (1979) suggested the existence of three metamorphic zones, not mentioning the haematite formation. It could be observed that the primary oxide phase in the IIF is magnetite and most of the hard haematite was derived from the metamorphic replacement of magnetite, forming micaceous or schistose haematite. Differently from most iron formations in the world, the formation of haematite deposits at QF occurred under high oxygen fugacity during metamorphism. The haematite microlaths display a strong preferred orientation, which determines the alongated shapes of the fragments. The terms foliated and unfoliated haematite have been applied by Dorr to the micaceous or schistose haematite, and to the isotropic, hydrothermally derived haematite. Under the microcope, the haematite exhibits a strong crystallographic or lattice orientation encircling the magnetite and martite porphyroclasts. The strain rate determined and defined the textural variation, size and economic importance of the deposits and the ore grade. Metamorphism at QF increases eastward and resulted in the formation of a gruneritic Fe-Mg amphibole, at the western portion, followed by a cummingtonitic amphibole at the central-western part, succeeded by the actinolite zone at the central-eastern part, and finally to the tremolite-anthophyllite zone to the east. These zones, arranged in a north-south pattern, can be followed in the pelitic units, whereas appear sericite-chlorite, kyanite-chloritoid and garnet-staurolite respectively. Carbonate geothermometry in IIF also may support the metamorphic variations. At the western zone the haematite forms small lenses within the itabirite, P-contents are slightly higher than in the remaining IIF, haematite grain size is minute, resulting in a submicaceous texture and the amount and dimension of relict magnetite within haematite is greater than in the other parts of QF. Jangada and Serra Azul deposits are examples of this zone. The central-western zone is characterised by significant haematite deposits, in considerable quantity and size, haematite grain size increased, in order to produce a micaceous texture, the P-contents and the amount of magnetite decreased. Pico do Itabirito, Cappo Xavier, Capitpo do Mato and Tamanduß correspond to the deposit type of this zone. At the eastern-central portion the amount of the hard haematite deposits decreases, increasing the soft haematite ore due to higher strain rates. However, it can be perceived that the relict magnetite almost disappeared and the haematite grain size became coarser than the haematite from the western zones. At the eastern zone, the haematite deposits exhibit typical schistose texture, the magnetite porphyroclasts are absent and the lowest P-grades in the haematitic iron formation. The haematite bodies characteristic from this zone are Andrade, Morro Agudo and the deposits at the Itabira District. The hydrothermally derived compact and isotropic haematite deposits, formed subsequently to the micaceous haematite bodies, were generated after deformation ceased, but under very high fluid pressure. The metamorphic reactions magnetite + quartz + H2O = grunerite + haematite and magnetite + quartz + H2O = grunerite + O2 were decisive in the formation of the metamorphic haematite deposits.

Jan 1, 2007

By Antônio Demouthie de Sales Rolim Esmeraldo

As indústrias de cerâmica vermelha têm grande importância na região assim como a mineração e beneficiamento de calcário laminado representam um importante segmento econômico do Estado do Ceará, entretanto produzem uma grande quantidade de resíduos, que poluem e agridem o meio ambiente. Assim, esse trabalho tem por objetivo a caracterização da incorporação do resíduo da Pedra Cariri avaliando sua aplicabilidade como matéria-prima cerâmica alternativa para a produção de telhas cerâmicas. Foram formuladas composições contendo o resíduo e confeccionados corpos-de-prova por prensagem. Os corpos-de-prova foram queimados e, em seguida, foram determinados a cor após a queima, perda ao fogo, retração linear, absorção de água, porosidade aparente e o módulo de ruptura à flexão. Obteve-se uma com avermelhada, com um tom mais claro nas que tiveram a pedra cariri na massa. Também foi visto uma porosidade, juntamente com uma absorção em nível aceitável para tijolos cerâmicos e a tensão de ruptura aumentou em 5% e decaiu em 10%. Após todos os testes feitos, provou-se que o resíduo tem a possibilidade de ser usado na incorporação de até 5% de resíduo em formulações para a produção de telhas cerâmicas.

Aug 17, 2017

By V. Rajaram

Rock reinforcement systems are used in open pit and underground mines to stabilize the rock mass in-situ and provide safe working conditions. Significant progress has been made to date in the design and implementation of rock reinforcement systems to accommodate bad rock conditions and larger excavations. However, the rationale for the design of rock reinforcement systems remains essentially the same and can be categorized into three groups, namely 1. to create a beam of competent rock in stratified formations, 2. to resist sliding motion in jointed rock, 3. to passively support the superincumbent loads in highly stressed ground. Case histories of the rock reinforcement sys¬tems that illustrate these design approaches will be presented in this paper.

Jan 1, 1983

By M. E. Steidlitz

FABRICATION of semiconductor devices.requires the formation of electrical contacts, often involving the use of lead, tin, and lead-tin solders. In several recent instances when germanium had been bonded to nickel with lead, a new metallic phase appeared, unattached to either germanium or nickel, but rather suspended as a continuous foil wholly contained within the lead matrix. Since such metallic structures do not form in nickel-lead or lead-germanium systems under identical conditions, a brief study was made of the characteristics and possible formation mechanisms of this material. EXPERIMENTAL Specimens were prepared by placing single crystal, transistor-grade germanium discs, 30-mils in diam by 6-mils thick, into a depression in a graphite boat. =A* nickel washers, 125 mils in diam by 5-mils thick, containing a center hole of 10-mils diam, and coined into a soup bowl shape, were loaded on top of the discs, so that the bottom of the

Jan 1, 1959

By Caroline Gomes de Oliveira

A busca por materiais que atendam as demandas ambientais que vem surgindo com o passar dos anos abre um importante mercado para a aplicação de fibras naturais. Além de biodegradáveis e provenientes de fontes renováveis, as fibras naturais possibilitam a produção de materiais compósitos de baixa densidade e com boas propriedades mecânicas. Para aumentar ainda mais essas propriedades, estuda-se o uso de tecidos de fibra natural em vez das fibras alinhas. As principais vantagens desta nova configuração são o reforço em mais de uma direção ao mesmo tempo e o fato de serem mais compactos, viabilizando a incorporação de uma fração maior de material de reforço. O presente trabalho investigou a resistência ao impacto de compósitos de matriz poliéster reforçados com tecido puro de rami, que é uma das fibras lignocellusosicas mais resistentes encontradas até hoje. Os corpos de prova foram reforçados com 1, 2 e 3 camadas de tecido e foram ensaiados num pêndulo de impacto Izod. Concluiu-se com base nos resultados que o aumento da fração volumétrica de tecido aumenta a resistência ao impacto dos compósitos.

Aug 17, 2017

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By Theodore J. Williams

Computer control has been one of the fastest moving and most glamorous fields of industrial development in the past decade. A review of this period shows some truly remarkable accomplishments in both system development and applications. In addition, work now under way promises results which will continue the rate of progress of the past. This paper will review the history and status of the field of computer control and point out the major breakthroughs which have occurred. It will analyze the present trends and extrapolate them to predict the early future developments in the field.

Jan 1, 1968

By R. J. Colony

MINING geology does not lend itself - very readily to a review embracing "improvements in methods," as perhaps do shop practices or laboratory procedures. The "methods" used in mining geology are simply the application of geology to mining; winning the ore, the handling of material, mechanical appliances, all belong strictly to mining proper, and have no place in a review of geology as applied to mining. A comprehensive review would necessarily cover a .very broad field, which could be subdivided into many -parts. Only a few of these can be discussed here. .Those that have been suggested to the chairman indude :

Jan 1, 1930

ABSTRACT This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By Ruth Escobar

Así como los seres vivos necesitan del oxígeno para vivir, las empresas mineras precisan de un modelo de innovación exitoso para ser competitivas hoy y en el futuro, esta es la síntesis del trabajo de investigación aplicada que la autora ha desarrollado durante 12 años de dedicada y satisfactoria labor, probando y perfeccionando un modelo de innovación minera denominado Innova, que se basa en la búsqueda de la adición de valor sostenible a una organización, desde la mejora continua de los procesos mineros a la creación de nuevas herramientas y métodos a partir del intraemprendimiento nacido del intelecto e ingenio de sus propios trabajadores a todo nivel.

Sep 30, 2022

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By L. E. Eary

Many of the major international gold mining companies provide data on rates of greenhouse gas (GHG) emissions as part of their environmental reporting commitments. These data are evaluated by an index defined as the annual GHG emission rate in metric tons, divided by the annual amount of gold produced in grams, and referred to as GHGgold. This paper examines ranges of GHGgold values for a cross section of gold mines as a function of mining method (openpit, underground and combined operation) and ore-processing method (mill, heap leach and combined methods) for reported ranges of operational data, including annual total tons mined, ore processed and gold grade. The evaluation shows that ranges and distributions of rates of GHG emission are approximately similar across different mining methods and ore-processing methods. The data presented in this paper provide the context needed to make comparisons of GHG emissions reported in companies’ annual reports to the ranges reported for the overall gold mining industry.

Jan 1, 2009

Once and for all, the debate on the exponent in Gy's formula is pushed to its limit. It is explained why an exponent of 2.5, obtained when using a square root of nominal size d to adapt the value of a calculated liberation factor to a different comminution size, will rarely be encountered in practice, if no arbitrary decisions are made.

Mar 1, 2010

Research 86 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1986

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012