Search Documents

By Healy T. W, Dixon D. R

The present study 'of pure ZnS and NiS and ZnS (marmatite) by detailed electrokinetic methods has shown that by careful control of experimental parameters much new' information on sulphide-water interfaces can be obtained. Time-dependent processes of alteration of sulphide surfaces are foHowed by electrokinetic methods and indicate that the isoelectric point of the surface depends on elemental sulphur coverage, oxidation product coverage, and the conditions which promote or minimize such reaotions in the presence and absence of activator.

Jan 1, 1977

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting & Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. "V. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K Thomson, W. G. Derby, and the assistants of the writer, K. 1V.McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the aid of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate anyone method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By Daniel Lozada

La unidad de producción polimetálica de Yauliyacu, ubicada en la localidad de Casapalca, Lima, tiene una presa de relaves en el paraje de Chinchan del mismo departamento. Sin embargo, dado que la presa nueva Yauliyacu culminaría su función y que la presa auxiliar Tablachaca no contaba con la suficiente capacidad de almacenaje, Centromin Perú evalúo otras alternativas para la ubicación y construcción de una nueva. De acuerdo al estudio realizado, se encontró que la quebrada de Chinchan era la más adecuada puesto que ofrecía mayor capacidad de producción y se descartó las de Corina y Tablachaca. En este sentido, el presente texto describe las características de la quebrada, el diseño del depósito de Chinchan, su proceso de construcción, la limpieza de fundación, el análisis de la estabilidad física y química, la implementación para mejorar la estabilidad de la presa, la mejora de calidad del aire en la zona del depósito, el programa de inversiones y el plan de cierre del relave.

Sep 13, 2001

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By Harsh Kumar Verma

Blasting off-the-solid is the most commonly used method during development of galleries in Bord and Pillar method of underground coal mining. In this method, only P5 explosives are used with permitted delay detonators in accordance with the safety requirements stipulated by the regulatory bodies. Delay detonators made with pyrotechnic delay compositions have inherent scattering in their delay timings. It is desirable to use precise detonators to achieve better fragmentation, less vibration and noise. Overlapping of delay period is undesirable from production as well as safety point of view.

Jan 1, 2008

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada's imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By Christophe Bragard, Marte Gutierrez, Haotian Zheng, Michael Mooney

This paper proposes a framework for applying surrogate-based approaches to evaluate SEM construction, which can both benefit the uncertainty analysis in the design stage and real-time calibration during the construction process. The performances of four surrogate modeling approaches, namely back-propagation neural network (BPNN), support vector regression (SVR), random forest (RF), and polynomial chaos expansions combined with Kriging (PCK), were evaluated and compared. A variance-based global sensitivity analysis (GSA) was performed on the surrogate predictor to quantify the impacts of geotechnical parameters on the deformation responses induced by SEM tunneling. The Regional Connector Crossover Cavern project constructed in Downtown Los Angeles was set as the benchmark problem to demonstrate the efficiency and reliability of the proposed procedure.

Jun 13, 2021

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

This paper describes certain analytical methods used at the Rosepery Mine and Treatment Plant of the Electrolytic Zinc Co. of Australasia Ltd., which are not generally in use and may therefore be of more interest than a description of the normal routine methods which are used in most of the mining assay laboratories of the Commonwealth, and which have been published previously.The ore mined and treated at Rosebery is of a complex nature and demands closer control in the concentrating plant than is necessary on some other similar mining fields.It is necessary for the mill shift supervisors to keep constant control on the grade of lead and zinc concentrates produced on their respective shifts, and further, it is essential to maintain an economic compromise between grade of concentrates and the recovery of the particular concent:t:ate. This necessitates a more frequent check on concentrate grade tp.an is provided by the daily assays carried, out by the assay office. Rather than employ trained ,assayers on shift work, "quick methods" of analysis, which could be carried out by the operators, 'were adopted.'In such methods, it is desirable that the necessary manipulation should be reduced to the following:-a. Taking the sample, drying and mixing.b. Weighing the necessary amount of sample-for assay.c. Adding the reagents for use in the assay without change of beakers.d. Titration and calculation.Such a contraction of, the normal technique would be impracticable for many determinations, but in the case of lead...

Jan 1, 1949

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 25°, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By R. Knapp, R. Firlotte

"Les Terrains Auriferes (LIA) Property, formerly the Malartic Goldfield (Goldfield) mine, ceased its remaining milling operations in the fall of 1994. During the early years of mining, the mill processed a non-sulfide ore with substantial carbonate mineralization.In 1977 after an extended shutdown period, ore from a nearby property, Bousquet, was processed at the mill. That ore contained larger quantities of sulfides, and unlike the old tailings, had acid generating potential.Upon closure of the L TA mill, the closure options considered for the L TA site were to cover with:1. a thin cover of 0.5 metres of borrow material (sand and gravel) to achieve basic erosion protection/stabilization; collect acidic seepage and treat with lime.2. a 2 metres of non-acid producing tailings; final surface to be vegetated.3. an engineered oxygen barrier consisting of a multi-layer cover; final surface to be vegetated.The paper presents the technological and economical methodologies that were used to select the closure alternative, describe the associated construction challenges that were faced with the implementation of the multi-layer cover concept and presents preliminary results on the cover's performance.In addition to being the first full scale demonstration of this type of multi-layer engineered oxygen barrier cover technology, this project had the advantage of using non acid producing mine tailings as part of the reclamation solution."

Jan 1, 1997