Search Documents

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson. Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001.000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,471,000 tons under less than 60 feet of cover.

Jan 1, 1966

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners' caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By Michael S. Moats, John Bailey Fletcher

Wear rates of grinding media can be misrepresented by marked ball wear tests (MBWT). Galvanic interactions between dissimilar grinding media can be affected by the chromium content in the media and the presence of oxygen in the environment. Corrosion, one component of wear, can be affected by many variables. Corrosion rates and corrosion potentials for modern high chromium white iron (HCWI) and high carbon steel (HCS) grinding media samples were obtained through electrochemical testing. In this study, the impact of chromium content in the grinding media and the dissolved oxygen in a simulated mill water solution on corrosion rates and potentials was examined. Increasing chromium content in HCWI above 15 weight percent increases the corrosion potential and decreases corrosion rate. Removing most of the oxygen from the solution lowers both the corrosion potential and corrosion rate of the materials tested. The electrochemical results were examined to model possible galvanic coupling effects on corrosion rates. Galvanic coupling between HCS and HCWI could cause differences in corrosion rates for almost all scenarios modeled. Based on the galvanic coupling analysis, MBWT results could be impacted by mixing HCWI and HCS in a ball mill charge. This impact is predicted to be more significant when dissolved oxygen is present in the mill water and as the chromium content of HCWI is above 15 weight percent.

Dec 21, 2022

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980

By H. J. Sandri

In the spring of 1991, Western Aggregates, Inc. began operating the newest expanded shale lightweight aggregate operation in North America. The operation is located in Jefferson County, Colorado, just south of Boulder, at the sight of the former Ideal Basic Industries ("Idealite") lightweight aggregate plant, which was decommissioned in 1975. The "new" facility has been built to principally serve the Denver and Front Range markets, as well as ship products into other locations in Colorado, Wyoming, New Mexico, Kansas and Nebraska. Western Aggregates is a wholly-owned subsidiary of Inco U.S., a subsidiary of Inco Limited of Toronto, Canada. Inco Limited is the free world's largest producer of nickel and is a leading producer of copper, cobalt, gold, silver, and platinum group metals, high nickel and super alloys, and specialized engineered products. Inco is constantly seeking new mining related investments that leverage off its mining and processing skills and that meet corporate fmancial objectives. Construction materials are an area presently being pursued by Inco. The basic 'building blocks' of society, from a construction perspective, are sand and gravel, stone, and aggregates. To the vast majority of people these are natural products that are mined, quarried or dredged, and other than washing, screening and crushing, are generally used in their primary form. While these materials vary from quartzite river rock, to calcified limestone, to hard basalt, they are generally classified as "heavy" aggregates. There are, however, other types of aggregates that do not fall under the "heavy" classification, but are used in general construction activities just the same.

Jan 1, 1992

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By J. D. Pitts

The worldwide production of iron ores was approximately 880 million metric tons in 1975. This level is the result of an annual growth rate of nearly four percent during the period 1967 to the present. The high growth rate was particularly significant in that two relatively severe worldwide recessions occurred in 1971 and 1975. The current upturn in world economic growth will probably allow future annual iron ore production growth rates in excess of the four percent figure, and, in fact, the International Iron and Steel Institute (IISI) has predicted that a five percent rate should be realized through 1985. The IISI figures would indicate a 1.4 billion metric tons per year output by 1985 or an increase in current production levels of around 500 million metric tons per year (MMTA)1. Even the more conservative four percent growth rate prediction from historical data would provide an 2 increase over current figures of nearly 350 MA by 1985. A large portion of world iron ore production is being provided by large resource-rich countries with relatively new industrial bases. These countries are typified by heavy export of raw materials such as iron ore and ore products and a large capital investment in the facilities to recover these raw materials. Brazil and Australia are typical of such countries and, indeed, their production of iron ore in the period 1967 to 1973 increased at annual rates of 17 to 30 percent, respectively, The continual reassessment of resources in these and other major iron ore exporting countries such as Venezuela and Liberia would indicate chat these high growth rates may continue for some years to come to meet anticipated world demand for raw steel production.

Jan 1, 1976

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By Herly Alcázar

El presente trabajo describe el proceso de optimizacion en la fundición de precipitados de oro y plata en la refinería de la mina Pierina a través del control de los diversos parámetros que involucra dicho proceso. Para ello, se trabajó con composiciones ternarias cercanas al punto peritéctico y asi procesar adecuadamente el tipo de precipitado. Entre sus principales logros de optimización tenemos: el incremento de oro y plata, el rendimiento de los crisoles, la reducción de los costos por consumo de reactivos y el mantenimiento de la calidad del precipitado.

Sep 13, 2001