Search Documents

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979

By Samuel Canchaya Moya

Si bien en las últimas décadas se aplicó el estudio de la geoestadística en la minería, el uso de la técnica no ha logrado una mayor difusión. En ese sentido, el presente texto señala la aplicación de los paquetes de software en la minería a través de los módulos de geoestadística. En este punto, la optimización del muestreo, se convierte en un problema tanto en la etapa de exploración como de producción. Por ello, es necesario conocer y comprender los conceptos y métodos geoestadísticos que se apliquen a la medida de muestreo de la veta, ver distancia y ubicación de taladros, costos de campaña de exploración, entre otras medidas, etc.

Jul 31, 2003

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

The Greymouth Coal Project is a proposal to mine by the application of proven hydraulic, and room and pillar underground mining methods; and to process the equivalent of an average of 1.7 million tonnes per year over a forty-year period. The proposed mine site is located ten kilometres north of Greymouth, on the west coast of the South Island of New Zealand. Of the three separate mineable seam groups, the thick Main Seam Group, which makes up 77% of the total resource, will be mined by hydraulic mining technology.   It is proposed to market and produce a high volatile bituminous type coal with low ash (6%) and sulphur (0.4%). Because the inherent ash content is low, the requirement for coal treatment will only be the use of a single cell jig circuit to control the effects of rock dilution and partings. The resulting coal product is tentatively planned to be transported by rail to the port at Lyttelton for loading on to Panamax or Post Panamax size vessels.

Jan 1, 1997

By W. W. Adams

[Sales of explosives - permissible explosives5/ other high explosives, and black blasting powder - in the United States during the calendar year 1937 reached a combined total that slightly exceeded the quantity sold in 1936. A larger output was reported for permissible and other high explosives but a smaller for black powder. Production of the three classes of explosives totaled 404,744,294 pounds, more than 3 percent over 1336. The total quantity produced included 49,579,441 pounds of permissible, 288,924,253 pounds of other high ex- plosives, 36,403,950 pounds of black powder in pellet form, and 23,836,550 pounds of black powder in granular form. Sales of granular black powder declined 26 percent compared with 1936 and of pellet black powder 12 percent; gales of permissible explosives increased nearly 4 percent and of other high explosives 10 percent]

Jan 1, 1938

By C. W. Smith

The U.S. Bureau of Mines conducted research to determine the effect of ground water control on the dewatering of phosphatic clay wastes. Two storage impoundments were constructed. One impoundment was surrounded on three sides with a series of well points (shallow vertical wells) to lower the ambient water table and the second impoundment served as a control. Ground water was pumped from the area surrounding the test impoundment for a period of 490 days. A constant pumping rate of 60 gal/min resulted in a water table drawdown of 13 ft, approximating the bottom of the impoundment. At the end of the test period percent solids in the test impoundment was 35 pct, while in the control impoundment percent solids was only 26.8 pct. Percent solids of greater than 30 pct is required for capping and final reclamation using fertile overburden.

Jan 1, 1989

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two o f the pit lakes, 26- and 55-m (85 and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper, pit lakes, 110 and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1997

By Black PM, Itaya T

Arc-type volcanic activity has been a major feature of the late Cenozoic geological evolution of the Pacific-Australian plate boundary in the northern New Zealand region. The timelspace distribution patterns of arc-type rocks reflect changes in the nature of the plate boundary as it has evolved. Inception of volcanism began in the north during earliest Miocene times (26 Ma) following ophiolite emplacement and during the next 10 Ma developed into a volcanic arc segment extending south to the present position of the central North Island. The northern part of the arc became extinct about 15 Ma ago, but activity continued in the central (Coromandel) part of the arc until about 5 Ma ago. In late Pliocene and Quaternary times volcanic activity has become concentrated in a northeast trending zone which is collinear with the Tonga-Kermadec Arc.

Jan 1, 1995

By Hori M, Komatsu T

In Japan, a small-diameter tunnel boring machine (TBM) of diameter 2.6 m applicable to a wide range of geology from hard rock to soft strata was developed with the purpose of reducing construction costs of headrace tunnels for small hydroelectric power stations. And in 1983, a demonstration test was carried out in the No. 1 headrace tunnel work of Hayakido Hydroelectric Power Station. The principal achievements in executing work are the following: (1) Although this TBM was a demonstration test unit, excavation advances averaged more than 200 m/month and exceeded the average 150 m/month with a conventional method. (2) According to PS velocity surveys after tunnel excavation the zone of loosening due to the TBM method was small enough to be ignored and was approximately one-half compared with conventional methods in rock of the same evaluation.

Jan 1, 1987

By Jr. Flynn

The filtration process has long been utilized in the mining industry and typically associated with processes where clear solutions are required. One definition of filtration states that it is utilized to affect a more complete separation of liquid and solid phases than is possible with settling alone. The development of Diatomaceous Earth filter aids has added a new dimension to filtration technology in the mining industry. It makes possible the filtration of slimes with almost perfect clarity, and at rates that become economical.

Jan 1, 1980

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Deno M. Pappas

The purpose of this Bureau of Mines study of U.S. roof and rib (roof- rib) accident statistics and related accident costs is to define current accident trends (1980-84) associated with fatal and nonfatal roof-rib fall accidents. Data were retrieved from a data base containing all recorded U.S. mining accidents, then sorted and normalized utilizing a computer software program. The statistics indicate that roof-rib accidents have significantly declined in the 5-yr study period. Moreover, they indicate that there have been increases and/or patterns of roof-rib accidents associated with specific mine characteristics, such as seam height, mine size, geographic location, and seasonal variations. Also, roof-rib injury characteristics produced pattern changes involving worker activity, lost workdays, types of injury, and severity of injury. A conservative estimate indicates that there has been a 30% adjusted increase in the cost of a roof-rib accident over the 5-yr study period.

Jan 1, 1987

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By G. R. Heckman, H. J. Murphy, C. T. Sims

An incestigation has been made of the effects of heat treatment and alloy composition on the long-time stress-rupture properties and structural stability of the similar nickel-base alloys Udimet-500, Lrdimet-520, and Udimet-700. Rupture test data are presented at stresses ranging from 4 to 50 ksi at temperatures from 1450° to 1900°F for times up to 14,000 hr. Ductility response is emphasized. Optical and electron tnicroscopy were complemented by X-ray diffraction analyses of extracted phases to relate microstructural stability to the observed rupture properties. Particular attention is paid to Udimet-520 since structural characteristics of this alloy appear to vary somewhat from its sister alloys. Both cast and wrought performance of Lrdimet-500 are discussed. The computerized PHACOMP calculational technique, based on electron-vacuncy theory, is discussed and related to structural stability where appropriate. Electron microscopy and microprobe techniques were used to conduct evaluation of the oxidation characteristics of Udimet-500 exposed in air for 16,100 hr. The steady advance in strength and reliability of nickel-base superalloys continues to be one of the high points of modern metallurgy. The stress capability of these materials has increased steadily, allowing higher and higher operating temperatures in the highly sophisticated aircraft and industrial gas turbines now on the market. The attendant increase in efficiency, of course, means greatly improved power output. Gas turbines for industrial and marine use have long been designed with these objectives paramount the usual design requirements in terms of time of service being 100,000 hr. High-efficiency, long-life aircraft such as the supersonic transport require superalloy engine materials with high-strength and long-time structural stability. Thus, materials studied for and operating experience from industrial gas turbines provide a good reservoir from which technology of high value to the SST program can be drawn. This study is one such case. Three prominent nickel-base super alloys—Udimet 500, Udimet 520, and Udimet 700 were extensively evaluated for industrial gas turbine bucket use. Particular attention was directed toward structural stability as a requisite property. Within the present context, structural stability is defined as freedom from the propensity to form strength-robbing or embrittling phases such as u,p,x,or Laves, and the ability to maintain useful rupture strength and ductility throughout design life. MATERIALS The three alloys, cast Udimet 500 (U-500C), Udimet 520, and Udimet 700, were chosen for detailed evaluation based on preliminary studies which indicated that U-500C and U-520 possessed comparable rupture strength capabilities, and that U -700 had a greater strength capability but somewhat poorer ductility than wrought U-500. The nominal compositions of the three alloys, along with the compositions of the heats investigated, are presented in Table I. PROCEDURE Dimensionally rejected U-520 buckets from Special Metals Corp. heat 63370 were heat-treated using the four cycles delineated in Table 11. Cycle A was investigated to determine the effects of a shortened 1700°F primary age. Cycle B was considered a "standard" treatment. Cycle C investigated a higher solution temperature in combination with a shortened primary age, while cycle D assessed the effect of the higher solution temperature alone. These heat treatments were designed to produce optimum combinations of rupture strength and ductility through maximum y' development, the development of a y' grain boundary cushion, promotion of MC carbide degeneration reactions, and agglomeration of resultant M23CB. Since one of the premises of the evaluation of U-520 was that rupture strength would be equivalent to U-500, forged U-500 buckets from Special Metals Corp. heat 62916 were heat-treated with cycles A, B, and C to provide comparison. The heat-treated structures of U-520 and U-500 are illustrated in the 8700 times electron micrographs of Fig. l. The U-700 tested was all from 3-in.-diam hot-rolled and centerless-ground rod from Special Metals Corp. heat 2-1426. Two heat-treatment cycles were employed, E and F of Table 11. Cycle E is a standard four-step, triple-age treatment intended to provide an optimum match of strength and ductility through well-developed matrix and grain boundary y', as recommended by U-700 vendors. Treatment F is a shortened , single-age cycle which could provide a significant processing cost reduction should adequate strength and ductility be maintained. Following heat treatment, rupture specimens of U-500 and U-520 were machined from the buckets and tested. Standard rupture bars of U -700 were machined from the heat-treated rod and rupture-tested. Failed and withdrawn rupture bars were prepared and examined by optical and electron microscopy. Select specimens were electrolytically digested, and the residues analyzed for carbide and topologically close-packed phases using CrKa or CoKo radiation. Of the six different U-500C heats evaluated, five were cast by Misco Precision Casting Co. and one was cast by Haynes Stellite Co. Cast-to-size rupture bars

Jan 1, 1968