Search Documents

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By W. J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 in New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be widespread through much of the Tasman fold belts of Eastern Australia. Production is estimated to be some 500,000 carats from several small alluvial fields. Despite extensive exploration, though, no primary rock source carrying significant diamond content has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia during the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives. Of those, 180 have been confirmed to be diamondiferous. Only one pipe, however, the 1200 Ma high-grade Argyle lamproite and associated nearby alluvials, has proved to be economically exploitable. Its current annual production is 40 million carats valued at about US$400 million. Production from the open pit will be sustainable until at least 2003.

Jan 1, 1995

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964

By P B. Card

"The website www.economicevaluation.com.au, which had its origins at the Project Evaluation Conference 2009, provides a free way for industry professionals to teach themselves economic evaluation. At its core is a set of fast-moving modules and three worked examples.The website recognises that economic evaluation is a discipline with a hierarchy of three levels:decision-makingevaluating the project/businesshands-on modelling.There are a set of modules for each level that describe the concepts and activities in detail. These emphasise that the most important and rewarding work is the evaluation of Level 2. The economic model created in Level 3 is merely a working tool and should not become a sophisticated ‘trophy’ in Excel that only one or two people can comfortably use.Hands-on modelling contains three sets of practices designed to make any model rigorous and intuitive so that it can be easily understood and used by others in the project team. Even if the model develops into a long, detailed and complex workbook, it should remain easy to follow and be intuitive. The website advocates freedom to devise any architecture that best suits the project under study, but promotes rigour through the following practices:four cash streams and graphsthree architectures – concept, prefeasibility and feasibilitysix principles.The modules in the Level 2 evaluation use conversational language to describe in detail the broad range of activities needed to properly understand and characterise a project/business. It stresses that net present value is nothing more than the mathematical treatment of a whole set of opinions, is not an absolute truth and is only a fraction of the evaluation process. The modules describe in detail the range of economic metrics that should be computed and the full spectrum of equally important characterisations required to make the decision in Level 3.CITATION:Card, P B, 2016. Teach yourself economic evaluation, in Proceedings Project Evaluation 2016, pp 160–171 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By D. A. Rhys, M. Sieb, M. A. Prefontaine, C. L. Swanson, S. R. Frostad, H. Q. Smit

"Gold-silver mineralization at Red Mountain (1992 resource of 2.5 million tonnes grading 12.8 g/t Au and 38.1 g/t Ag) occurs within several discrete zones within a folded sequence of Middle to Late Triassic Triassic sedimentary rocks, Early Jurassic volcaniclastic and pyroclastic rocks, and Early Jurassic intrusions. Three phases of Early Jurassic sills and stocks collectively comprise the Golds/ide intrusions: (1) irregular bodies of medium-grained hornblende monzodiorite (Hillside porphyry); (2) hornblende-biotite + quartz porphyritic monzodiorite to quartz monzodiorite (Golds/ide porphyry; U-Pb zircon ages of 197.1 + 1.9 Ma); and (3) biotite porphyritic hornblende monzodiorite sills (Biotite porphyry). Contact breccias and igneous breccia dikes are common features of the Golds/ide intrusions. Chemical similarities and equivalent ages of volcanic rocks and intrusions, and the presence of intrusive clasts in volcanic rocks suggest that the intrusions are feeders to overlying volcanic units.Hydrothermal alteration affects all pre-Tertiary rocks on Red Mountain, including all phases of the Golds/ide intrusions. Several shallow-dipping alteration zones are developed sequentially above a propylitic quartz stockwork/molybdenum zone. These include: (1) sericite-quartz-pyrite alteration (pyrite-dominant alteration); (2) chlorite-K-feldspar-sericite-titanite alteration with disseminated and vein pyrrhotite (pyrrhotite-dominant alteration); and (3) brown to black tourmaline veins and K-feldspar-pyrite-titanite-actinolite alteration. Anomalous gold(> 0.3 g/t) mineralization is developed at the transition from the pyrite to the pyrrhotite dominant alteration over a > 1 km2 area. Within this anomalous zone, high-grade (3 g/t to 20 g/t Au) gold-silver mineralization occurs in 5 m to 29 m thick, semi-tabular pyrite + pyrrhotite stockworks with intense sericitic alteration and surrounding disseminated sphalerite + pyrrhotite.Stratigraphic, spatial and geochronologic relations and alteration zoning indicate that mineralization formed in a subvolcanic environment at the top of the Golds/ide intrusions and at the base of the Early Jurassic volcanic pile. The Golds/ide porphyry is interpreted to be the mineralizing intrusion. The alteration zoning, molybdenum-copper mineralized quartz stockworks, extensive Ksilicate and tourmaline alteration, and the relationship with a hypabyssal porphyritic intrusion show similarities to many porphyry systems."

Jan 1, 1995

By Stanley G. Hutton, Robert Brubaker

"It has long been recognized that mining workers subjected to high levels of hand-transmitted vibration may suffer from vibration-related complaints. Prolonged exposure to whole-body vibration may also result in adverse effects. In this study, the effects of vibration on mining workers are examined. Previous work documenting the occurrence of vibration-related disease is reviewed. From this work, it is apparent that operators of hand-held pneumatic rock drills are exposed to a significant risk of developing vibration disease. Vibration levels recorded on the rock drills now in use are presented and shown to exceed levels recommended by a proposed ISO standard.IntroductionThe possible harmful effects of exposure to excessive vibration levels have long been recognized, particularly among operators of hand-held tools. Numerous cases have been reported of a vasospastic disorder commonly known as vibration white finger disease (VWFD), which was a term coined by the Industrial Injuries Advisory Council in Scotland in 1970(1 ), Those suffering with the disorder have frequent vasospastic attacks in which the fingers, hand and, in advanced cases, the lower arm turn white and numb, usually after a cold stimulus. Advanced stages of VWFD have been reported in which the skin becomes ulcerated and gangrenousm. The incidence of the disease has been particularly serious in the forest industry due to the extensive use of chain saws. However, in recent years, the introduction of antivibration saws has resulted in a significant reduction in the occurrence of the disease.In a recent report for the Canadian Department of Supply and Services - Energy, Mines and Resources, Hutton & Brubaker considered the effects of vibration on workers in the mining industry. In this report, the physiological and medical effects of vibration were considered, relevant vibration standards were discussed, previous vibration measurements were documented and field measurements carried out. In the present paper, the results recorded in this study will be summarized, together with results that have been previously published relating to vibration levels existing in the mining industry."

Jan 1, 1982

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By R K. W Merkle, S Madoom Hussain, T Yellappa

Cr-Ni-Cu¦PGE deposits are known to occur in early Archaean mafic-ultramafic rocks. Early Archaean mafic-ultramafic (MUMF) rocks occur in the western Dharwar craton and range in size from small pods to schist belts. These MUMF pods consist mainly of meta-peridotites, tremolite-actinolite schists, serpentinites, amphibolites and metabasalts. Spinifex, nodular and ocelli textures are also present. The rocks have been subjected to greenschist and amphibolite facies metamorphism. Geochemical studies were undertaken to evaluate the possible occurrence of economically important elements in the mafic-ultramafic enclaves around the major Arsikere-Tavarkere lineament and surrounding gneissic terrain adjoining local shear zones that occur as discontinuous pods between Arsikere and Chennagiri. Talc-serpentine and tremolite- actinolite schists contain chromite which is rimmed by ferrit-chromite. A notable feature of these MUMF rocks is that they exhibit high MgO (22 - 40 per cent), total iron (8.34 - 10.01 per cent), Ni and Cr (~3000, 2800 ppm) contents, with some samples showing komatiitic affinity. The rare earth elements (REE) data show slightly fractionated patterns with enriched LREE (LREE/HREE ~5.0) and negative europium anomalies. The Pt and Pd values reach 6500 and 191 ppb. The MUMF rocks, especially those exhibiting high chromium contents and occurring near shear zones, are potential hosts for economic platinum group element (PGE) deposits.

Jan 1, 2008

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By Xiaofei Guan, Adam C. Powell, Uday B. Pal, Srikanth Gopalan

This paper reports a solid oxide membrane (SOM) electrolysis experiment using an LSM– Inconel inert anode current collector for production of Mg and O2 at 1423K. The electrochemical performance of the SOM cell was evaluated by using various electrochemical techniques including electrochemical impedance spectroscopy, potentiodynamic scans, and potentiostatic electrolysis. The effects of Mg solubility in the flux on the current efficiency and the YSZ membrane stability during SOM electrolysis were discussed and examined through experiment and modeling. The electronic transference number of the flux were measured to assess the Mg dissolution in the flux during SOM electrolysis. A negative correlation between the electronic transference number of the flux and the current efficiency of the SOM electrolysis was observed.

Jan 1, 2014

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By R. E. Scheffel

Most supergene copper heap leach operations today employ forced-aeration, irrespective of ore grade. Unfortunately, there is little published quantification of its benefit. There is a natural desire to strive for the ideal chemical kinetics. The reality, however, is that physical mechanisms control the commercial extraction rate. This paper presents the performance of a number of operations, their operating conditions and physical ore characteristics, which contribute to non-ideal solution distribution and variable extraction rate. Regardless whether one uses forced-aeration, commercial experience to date suggests it is prudent to design for longer leach cycle times to ensure the production target is met.

Jan 1, 2006

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defense, for purposes other than the: extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallics is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of they Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

By J. M. Elder, W. S. Kow

Challenges to new heavy mineral deposit developments are presented. These include land use issues, particle fineness, declining grades, and particle coating, amongst others. Industry responses to these are presented as possible solutions.

Jan 1, 2005

By K. Ramji

"The development curve in the extractive sector has become longer, steeper, and riskier due to increased social, legal, and political risks from various stakeholders. Indigenous peoples are a unique stakeholder because their growing legal rights to lands and resources can often determine a project’s outcome. A project will only be successful if it is able to obtain the legal permits, withstand any judicial reviews, and gain and maintain the social license to operate. Stakeholder identification, management, and engagement are key risk-mitigation tools required to successfully convert risks into opportunities.RÉSUMÉ La courbe de développement du secteur de l’extraction s’est allongée, elle est devenue plus abrupte et plus hasardeuse en raison de l’accroissement des risques sociaux, légaux et politiques venant des divers intervenants. Les peuples autochtones sont des intervenants uniques puisque leurs droits légaux croissants sur les terres et les ressources déterminent souvent ce qu’il adviendra d’un projet. Un projet ne pourra réussir que s’il est capable d’obtenir les permis légaux, passer à travers les analyses judiciaires, puis obtenir et maintenir le permis social d’exploitation. L’identification des intervenants, la direction et l’engagement constituent les outils clés de l’atténuation des risques nécessaires pour bien convertir les risques en possibilités."

Jan 1, 2016

Endless lines at service station gasoline pumps, limited travel at reduced speeds, thermostats set at an uncozy sixty-eight degrees in the dead of winter-these are but a few of the inconveniences and discomforts that awakened Americans to a realization that our domestic minerals resources, traditionally taken for granted, are not boundless. We begin to accept and practice principles of conservation, yet we are aware that this alone cannot appreciably forestall the inevitable depletion of our minerals, metals, and fossil fuels-resources critical to our Nation's economy. The key to warding off shortages is the development of technology that will insure a continuing, adequate supply of minerals and energy from reliable sources at the lowest possible costs to society and the environment. The mission of the Bureau of Mines is to develop this improved technology. Established in 1910, the Bureau of Mines of the Department of the Interior is the Federal Government's primary research arm in the minerals and fossil fuels fields. In addition to its research role, the Bureau keeps the Government informed of the Nation's mineral posture. The Bureau also seeks to stimulate private industry, through the awarding of grants and contracts, to produce minerals and fuels at a rate compatible with the country's increasing demands.

Jan 1, 1974

By M. Hitch, M. B. Lytle

Resource development conflicts arise largely due to differences in worldview between those who support and those who oppose development. This paper illustrates how societies and civilizations with different worldviews produce different levels of creative and economic energy. A questionnaire was created to build a database of responses to test whether worldview and resource development are correlated. Factor and multivariate regression analysis determined correlations for respondent groupings. Results showed a positive correlation between the respondents\u2019 worldviews and their attitudes toward resource development. Correlations became stronger as the homogeneity of the sample subgroups increased.

Jan 1, 2017