Search Documents

By Bruna Helena Malovini Loiola

Os aços ligados ao níquel especificados pela norma ASTM A 522 são utilizados na fabricação de válvulas, flanges e conexões de tubos, na indústria automotiva, na construção civil e na área naval. Na indústria de petróleo e gás, o material requer desempenho adequado para resistir às altas pressões, ao ambiente corrosivo e à abrasão. Considerando os efeitos do desgaste nas válvulas e flanges, este trabalho tem como objetivo avaliar o efeito da temperatura de revenimento na microestrutura e dureza do aço. Amostras submetidas à têmpera a 860°C e ao revenimento na faixa de 380 a 630°C proporcionaram resultados que mostram uma microestrutura predominante de bainita após têmpera e redução da dureza com o aumento da temperatura de revenimento devido ao alívio de tensão.

Aug 17, 2017

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

"Many industrial processes involve materials that are subject to temperature change and thermal stress. Examples range from the casting of large metallic products to the cooling and reliability of small electronic components. Thermally induced stress is a major concern as it can lead to material damage and product failure. Material properties, thermal and mechanical, and process conditions such as the size and location of a feeder in metals casting, or the power dissipation in a computer chip, will govern the magnitude of these stresses. Temperature may also be influenced by fluid flow, for example, the airflow over a computer chip in a laptop will govern the rate of heat extraction, hence the temperature gradients in the chip and the evolving thermal stresses.This paper provides details on the governing equations for heat transfer (temperature) and solid mechanics (stress), their degree of coupling, and the numerical techniques used to solve them. Three examples are discussed to illustrate the use thermomechanical modelling. These also provide an insight into the degree of coupling required between the equations. The first example, involves thermal cycling of electronic components where a prescribed temperature field is applied. As temperature is known, this example only requires the solution of the stress equation. The second example also involves the modelling of an electronic component where the temperature field is also calculated. In both of these examples, the stress calculation is dependent on the temperature field, but the temperature calculation is not dependent of the solution of the stress equation (one-way coupling). The final example provides details on modelling the metals casting process. Both the temperature and stress equations are solved but, unlike the previous two examples, in this case the temperature field is dependent on the results from the stress calculation (two-way coupling)."

Jan 1, 2001

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By Ali Kahriman, Alper Celtikc, Serdar Celik, Tuncer Gungor

This paper presents the results of ground vibration measurements carried out in Gülyali Hisarcik Basalt open pit mine located on the north side of the Anatolia near Ordu province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 5 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 5 different vibration monitors (4 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2013

By Martti Hagfors

The Finnish Defence Forces Technical Research Centre (PVTT) studied the effect of shape of boost-er to its ability to ignite insensitive (IM) plastic bonded explosive (PBX). Therefore an explosive fac-tory produced 20 insensitive (IM) plastic bonded explosive (PBX) charges for the tests. The mass of each of the charges was exactly 9.2 kg (20.3 lb). The charges were equipped by two different type of boosters; RDX and PETN. Both the explosives contained some parts of plasticizers. The weight of all the boosters was exactly 300 g (0.66lb). On the bases of their shape, the boosters were also divid-ed into two different groups, cylindrical and “pancake”. In the middle of the “pancakes” there was also shaped a small cone in such away that the detonation could accelerate to its full speed after the charge was ignited. The following shots were exploded;

Jan 1, 2013

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By A. McLean, M. Barati

In this paper, examples are presented of pyrometallurgical research and associated teaching activities during the past century within the Department of Metallurgical Engineering, now the Department of Materials Science and Engineering, at the University of Toronto. Throughout these years, pyrometallurgical research has been characterized by recognition of the importance of the interdependence of measurements and models as well as the development and application of sensors, for the generation, validation and practical implementation of new knowledge. The important role played in the delivery of lectures and participation in joint research by Adjunct Professors with strong backgrounds in the pyrometallurgical industry is described. Projects conducted in close collaboration with the industrial sector and opportunities for students to obtain practical experience working as teams on a "round-the clock" shift basis within an industrial pilot plant environment are outlined. These activities, together with the involvement of students in poster competitions and the presentation of papers at society conferences and technical meetings, are still vital elements in the development of pyrometallurgists equipped with the appropriate professional skills for subsequent employment within academia, government laboratories or the industrial sector.

Jan 1, 2015

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By AIME AIME

DOUBT in anyone's mind that this is the age of metals, industrially speaking, could easily have been dispelled by attending the National Metal Congress in Chicago, Sept. 22 to 26. Iron, copper and aluminum; zinc, lead and nickel, often alloyed with each other or with some of a dozen minor metals, make the materials without which the modern world could not run. Science, pure and applied, is doing marvels in finding new mixtures, new alloys to meet new needs; in developing new means of rolling, fabricating, casting and welding metals cheaply-and effectively. These and related matters were the subject of 100 papers presented at 33 seperate sessions of the organizations that participated in the congress.

Jan 1, 1930

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

By P. Matias

The study involved two projects that will produce copper concentrate and may have their operations integrated. Transport by trucks, conveyor belt, and the equipment called RopeCon were evaluated as options for the ore transport between the sites. A rainforest stretch, that Vale S.A. demands to preserve, is situated between the projects. It was suggested to further review RopeCon because it presents minimal interactions with the environment. To design the preliminary system layout, a research was done on the rainforest cover height data, but the information found was scarce and imprecise. For preserving the local forest, the use of this data would conduct to the oversizing of RopeCon towers and, consequently, overestimation of its costs. For the acquisition of reliable information, a method was developed using local data acquired through airborne laser survey. The volume between the digital surface and terrain models was calculated to generate a surface representing the forest cover height. It was revealed, by plotting the points obtained from this surface, that 85% of the vegetation is below 25 m. This height is suggested to review the preliminary project with a more accurate design of the equipment towers, thus reducing its costs estimates. The method permits the precise location of the large trees, making easier to find a pathway, for linear-shaped facilities, that would minimize the creation of vegetation-free zones as a measure to protect equipments against falling trees and forest fires. Keywords: forest cover, mining projects facilities, digital models, airborne laser survey

Sep 1, 2012

By P Standish

Qualitative risk assessment methods are not well suited to considering complex systems and potential interactions of new technology. As part of supporting tier one mining organisations and international industry groups, the author and colleagues have innovated processes to help provide better solutions to sites/companies considering a move to implementing proximity detection and collision avoidance systems. The process identifies required operating states for the system. By applying a combination of research and team-based analyses, a rigorous identification of credible failure modes which could cause these states to be lost, is identified. Finally, required business inputs, expressed in practical terms are distilled from regulator, industry, organisation and site in a way which clearly addresses the failure modes and so retain the required operating states. These business inputs identify improvements for site arrangements (EMESRT levels 1 to 7) before identifying functional requirements for technological collision avoidance solutions (levels 8 for advisory and 9 for autonomous). The paper presents a case study synthesised from multiple sites analyses and will provide guidance on where to find additional resources to assist in making the best possible transition to better equipment and road network solutions.

Jun 22, 2022