Search Documents

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By Rogerson R, Queen L

The petrology and age of mid Cretaceous to Palaeogene marine volcanics may provide important clues to the palaeogeography of the period, particularly for tectonic elements and events outboard of the Papuan Basin. This initial survey of known marine volcanics of this age reveals a paucity of reliable data on isotopic ages, geochemistry and syngenetic mineralisation on virtually all units. Existing data allows a tentative subdivision of known marine volcanics into either MORB-like early Palaeogene rifts/ marginal basins, early Palaeogene ensimatic arc rocks overlying ?Late Cretaceous and Palaeogene fore-arc/marginal basin crust, late Palaeogene ensimatic arc rocks, and mid to Late Cretaceous ensialic rift rocks. Due to lack of data, some units are difficult to classify into these categories.

Jan 1, 1991

By Steven E. Mischler, Jon C. Volkwein

A diesel particulate matter analyzer capable of direct, real-time measurement of engine exhaust particulate is necessary to effectively institute source control technology currently being used on diesel equipment and to ensure that the control measures are working. To investigate the potential of a differential pressure monitor to measure diesel particulate matter in undiluted exhaust, samples were collected from three different diesel engines-Kubota, Isuzu, and Deutz-running under 12 different RPM and load scenarios. These measurements were compared to elemental carbon concentrations in the sampled exhaust as determined by using the NIOSH 5040 analytical method. Elemental carbon is used as a surrogate measurement for diesel particulate matter. The results of the two data sets were then compared using a linear regression analysis. The coefficient of determination (or R2) was calculated to be 0.98, 0.94, and 0.74 for the Kubota, Deutz, and Isuzu engines, respectively. R2 values of this magnitude indicate that this method can be successful in estimating elemental carbon emissions in the engines tested. In addition, for replicate samples, the coefficient of variation ranged from 7.1% to 10.2% with an average of 8.5%. These data indicate that this method could prove useful to mechanics as they work to maintain engines and DPM control technologies.

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By L. R. Raymond

With the trend toward deeper and consequently hotter holes, measurements of drilling mud properties at atmospheric temperatures are becoming increasingly inadequate.' Both the prediction and control of down-hole mud properties depend in part upon our knowledge of temperatures in the wellbore. Consequently, a better understanding of factors that affect temperatures during circulation and trips could improve drilling operations. It was toward the goal of obtaining this understanding that this study was directed. Other investigators2 have studied the response of fluid temperature in the borehole during trips. However, all of these studies have used an assumed formation temperature profile at the conclusion of circulation and have provided no means to calculate this profile directly. In this study, the formation profile during circulation was calculated. Other investiga-tors3-5 have also studied bottom-hole temperature during circulation. However, they have developed neither general techniques for calculating the entire temperature profile in the system nor generalized methods for predicting bottom-hole fluid temperatures during circulation. Such techniques and methods have been developed and are discussed briefly in the following pages. Temperature Behavior During Circulation Circulation of fluid during the drilling operation is represented schematically in Fig. 1. The process of circulation has three distinct phases: (1) fluid enters the drill pipe at the surface and passes down the drill pipe; (2) fluid exits the drill pipe through the bit and enters the annulus at the bottom; and (3) fluid passes up the annulus and exits the annulus at the surface. To simulate the thermal behavior of the fluid in the system, each of the phases of circulation must be described mathematically. In Phase 1, the fluid enters the drill pipe at a specified temperature, TDo. As the fluid passes down the pipe, its temperature is determined by the rate of heat convection down the drill pipe, the rate of heat exchange between the drill pipe and the annulus, and time. Phase 2 of the circulating process merely requires that the fluid temperature at the exit of the drill pipe be the same as the fluid temperature at the entrance of the annulus; i.e., TD(L,t) = TA(L,l). Thus in Phase 3, the fluid enters the annulus at TD(L, t). As the fluid flows up the annulus, its temperature is determined by the rate of heat convection up the annulus, the rate of heat exchange between the annulus and the drill pipe, the rate of heat exchange between the formation adjacent to the annulus and the fluid in the annulus, and time. These rates of heat exchange and the time dependency of mud temperature are described by well known heat-flow equation.6 Consequently, as shown in the Appendix, the temperature profiles in the drill pipe, annulus, and formation can be obtained by solving Eqs. 1 through

Jan 1, 1970

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By M. Tarvainen, J. Kallioinen

"Depressed metal prices coupled with increasing production costs have presented a great challenge for operators to control and reduce the costs of production to maintain profitability. Depleting ore reserves, added to the above has forced Outokumpu to take a hard look at its operations, to develop new methods to profitably extend the life of its mines. One of the areas investigated and approved for further development has been the use of larger and more energy efficient equipment. As a result, large flotation machines were developed and today 38 and 60m3 flotation machines are in use.Secondly, ore preconcentration has been developed to avoid processing the part of the ore that has little or no mineral values.Another quite recent development and the topic of this paper, has been the use of coarse flotation before conventional flotation. The main idea is that part of the valuable mineral is separated as early as practical by floating it with specially designed flotation equipment, installed in the grinding classification circuit. The new flotation cell is specially designed for this application and differs from the conventional cells in the tank design, feed arrangement and modified mechanisms in some cases."

Jan 1, 1984

By H. Mischo, R. Ellmies

Uranium has been mined in Namibia since the 1970s. The worldwide increasing need for energy in the early 2000s has led to the development and opening of a second uranium mine in 2007 and has triggered an increased interest in uranium exploration, often referred to as “the Namibian Uranium Rush.” In all, four mining licenses have been granted by the Namibian Government, which currently has two mines in operation, a third undertaking trial mining and the fourth in project finance negotiations. In addition, highly intensive prospecting activities at additional deposits are at an advanced stage. The finalization of the strategic environmental impact assessment (SEA) on uranium mining in 2010, the first of its kind and scale in the world, has enabled the Namibian government to assess this uranium rush and its tremendous legal, socioeconomic and environmental impacts and to prepare for the different future scenarios conceivable when this article was written in 2011, including both a skyrocketing and a complete breakdown of demand scenario. The Fukushima disaster and plans of the Namibian government to significantly increase royalties and company taxes in 2011 have threatened the market situation, forcing investors to reevaluate Namibian uranium mining projects. However, with the tax and royalty increase initiative since withdrawn, most projects are back on track at this point in time.

Jan 1, 2012

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By Nathan T. Lowe

This report updates an accounting of mines and prospects in the Seafoam mining district, Custer County, Idaho, begun during mineral appraisal of the Idaho Primitive Area. Thirty-two mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of mineral appraisal of the River of No Return Wilderness; most previously known locations were field checked and the updated information added to the data base. The district's major deposits include polymetallic fissure veins of gold-silver-lead-zinc-copper hosted by granodiorite and quartz monzonite which have been intruded by dikes ranging in composition from rhyolite to dacite, and vein type replacements of silver-lead-zinc-copper hosted by calcareous xenoliths imbedded in major intrusives. These deposits may be related to the intrusion of the Rapid River pluton or the Casto pluton. The dominant northwest structural trend is parallel to an aeromagnetic high, a weak gravity salient, and the Blue Bunch Mountain dike swarm.

Jan 1, 1983

BATMINÖ, BATMINEÖ, BATMINDÖ are an abbreviation for Business Analysis Tools for Mining, Mine Evaluation and Mine Design respectively. BATMINP are proprietary tools customised to suit individual client requirements. The first suite of tools provides for analysis and evaluation of open pit mining equipment alternatives and includes fleet selection, fleet sizing and production, productivity and economic outcomes. The models address all mine process activities including drilling, blasting, loading, hauling and auxiliary services. All models are built to provide for simultaneous evaluation of multiple alternatives that are time and condition related. Provision is made for modelling from first principles and/or default or shortcut inputs. Sensitivities to key input parameters are easily performed and consistent logic is applied throughout the process. The models are built to provide key outputs in a format suitable for presentation and documentation. Provision is also made in the models for validation of both inputs and outputs through benchmarking, back analysis and budget comparison. The same models can be used for short interval (12 month) planning and control, medium-term (three to five years) and long-term life-of-mine (LOM) planning. Millions of dollars are spent each year on mining plant and equipment. Decisions that impact on the medium and long-term are made. BATMINP tools have been used to perform studies with good results and in most cases the studies have been validated through back analysis and comparing model outcomes to real data.

Dec 6, 2010

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By Yung Sam Kim

The study of ultrasonic-wave propagation in substances has been remarkably advanced in recent years in most engineering and science fields. The main object in studying the velocity of ultrasonic-wave propagation in solids, is to determine dynamic properties of these materials. The present paper, however, presents some other possible applications of ultrasonic-wave propagation in the study of rock mechanics as follows: Investigation of the mechanism of microseismic activites of geologic materials, (a) at initial or low stress level, (b) at final or fracture stress level, and (c) under fatigue loading condition. Also, correlations among stress level, density, and the velocity of ultrasonic-wave propagation in rocks are discussed in this paper.

Jan 1, 1973

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914