Search Documents

By Mahyera A, Sakashita B, Ahmed U, Abou-Sayed AS

Gas in U.S. coals is primarily composed of 90 to 99 percent methane and up to 10 per- cent carbon dioxide. In composition and heat- ing value, this coal-bed gas is similar to natural gas and can be introduced directly into commercial pipelines after standard condition- ing. The high permeability cleat system in the virgin coal can be exploited in order to drain the coal gas well in advance of mining. Two premining drainage methods have been extensive- ly evaluated in the U.S.; they are 1) horizon- tal boreholes collared from within the mine, and 2) vertical drilling from the surface with fracturing. Limited-size fracture treatments are advocated in order to prevent potential roof damage and the need for added support. An engineering approach to predicting gas flow for different drainage techniques near mining locations is presented. Results can be used in design, i.e. pipeline, compressor. Coal gas drainage from a horizontal borehole and a treated (contained fracture) vertical well for a 6 foot seam have been evaluated. Based on these results, it was concluded that selection of gas drainage techniques will depend primar

Jan 1, 1982

By Marc Raithel, Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments and dikes on soft soils was introduced some 20 years ago and is now considered State-of-the-art in Germany, Europe and, step by step, worldwide. The GECs consist of compacted non-cohesive granular fill similar e.g. to common gravel columns with one decisive difference: they are confined in a high-strength, high-modulus, flexible geotextile “cylinder” (encasement). This engineered element with parameters being adaptable in a wide range provides a decisive tool to control and optimize the behavior of the GEC foundation system. Consequently, the GECs work properly even in extremely soft soils, and a wide range of fills inclusive of sands can be used. In the meantime vast design and technological experience is available and codified design methods exist. Initially the paper briefly describes the general idea, the basics and specifics of design, construction technology, materials, restrictions and optimal application areas. Then it focuses on three informative case studies. They are briefly presented focusing for brevity only on the most important facts and experience inclusive of the most meaningful data of short- and long-term measurement programs.INTRODUCTIONWhen considering embankments on soft soils, generally two groups of solutions exist:Unsupported embankments; there are four main options:a) build up embankment extremely slowly waiting for sufficient consolidation after every stage;b) replace the soft soil partially or totally;c) install a high-strength basal reinforcement providing overall and local stability and allowing much faster embankment construction;d) combine c) with strip drains to accelerate consolidation and thus the construction process additionally (Fig. 1, left).Today, practically only option ""d"" is of practical relevance. Despite all the pros and cons, the common attribute of all non-supported options is that local and overall stability (Ultimate Limit State-ULS) can be achieved and controlled, but not the short- and long-term settlements (Serviceability Limit State-SLS). The latter can be significant, e.g. up to 30% of the nominal planned embankment height. Supported embankments (Fig. 1, right): the main common idea is to over-bridge the soft soil layers by supporting vertical elements of different types: rigid piles, trench walls etc. or by ""softer"" solutions of different column types (compacted, cemented, mixed-in-place etc.). Herein the borderlines between “piles”, ""pile-similar elements"" and ""soil improvement” are fluent and depend on country, traditions, codes etc. The common attribute of the “supported” schemes is a minimized settlement. Twenty years ago a new specific solution was launched: the Geotextile Encased Columns (GEC), which is discussed in more detail below."

Jan 1, 2017

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By James Westfield

Bureau of Mines activities for safety and health in the mineral industries were reorganized during the fiscal year to provide direct supervision by the Assistant Director -Health and Safety. On December 19, 1954, the field offices conducting these activities were designated as district health and safety offices reporting to the Assistant Director. The functions of determining the causes of accidents and injuries in the mineral industries and recommending measures to eliminate them were continued, with satisfactory results in improved safety records. The inspection of coal mines and enforcement of the Federal Coal Mine Safety Act of 1952 were conducted as directed by the Congress, and safety conditions in the mines were notably improved. One coal-mine explosion classed as a major disaster occurred during the year. The causes of that explosion and means for preventing a recurrence were still under investigation because of the extreme difficulty in recovering several portions of the mine. Basic research on the nature of certain hazards and ways of eliminating them is continued. Training of individual workmen and supervisors in this knowledge is a major part of the work.

Jan 1, 1956

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By Robert Hopler

Earthquakes, ground vibrations, seisms, or whatever you want to call the shaking of the earth, have been a fact of life throughout time. In spite of this, most people (except those unfortunate enough to live in seismicallyactive areas) have probably never felt this phenomenon, or if they have, only a very few times in their entire lifetime. However, when it does happen, nothing is more frightening than the sudden shaking of the earth beneath us - after all, we think of the ground we walk on as the unyielding, solid underpinning of our existence.

Jan 1, 2006

By Thomas J. Crocker, Douglas B. Uthus

Tunnel Boring Machines (TBM) have gained worldwide acceptance in the construction field and are being employed in ever increasing numbers to drive underground transit lines, drainage systems, etc. However, TBM utilization in the mining industry, and more specifically coal mining, has been very limited. This paper reviews past and present applications of TBMs to coal mining and examines the needs of the industry in an attempt to offer some insight as to what a TBM system must provide if the excavation potential demonstrated in civil works projects is to be realized in coal operations. EUROPEAN EXPERIENCE Germany The Germans recognized long ago the potential of mechanized drivage for coal mine entry development. Early in the 1960's experimental runs were made with a full-face Wohlmyer roadheader at the Westerholt Mine and trials were conducted on a roller bit armed full-face Bade roadheader. But because of problems with penetrating the various carboniferous strata occurring in changing sequence and hardness, these first attempts were soon terminated. After viewing later successes in the construction industry with improved TBMs, new attempts were initiated by the German mining industry in 1971 to mechanize drivage of their development entries. Four TBMs of two different types were placed in operation.

Jan 1, 1976

By L McCracken

Up until 1990 CoalCorp North Island's accident record was six times that considered acceptable in those NSW operations with good accident prevention programmes. This was an obvious avoidable burden on the company in both human and cost terms.   Late in 1989 an accident prevention programme was implemented with the objective of achieving a 50 per cent reduction in the lost time accident frequency rate within 12 months. The key to achieving this objective was recognised as being an attitude change in the total workforce from General Manager downward. Management commitment and action were seen to be critical to the success of the programme.   Through very basic and simple training programmes in accident investigation, analysis and reporting, communication, on-the-job coaching and in focusing on improving supervision skills, the original objective was achieved.   During 1991 the application of methods improvement and hazard recognition techniques are seen as the logical step to achieving a further 50 per cent reduction in the accident frequency rate.

Jan 1, 1991

By Richard H. Otto

Three longwall mining methods practiced in foreign countries are described that have potential for increasing underground recovery and productivity in thick coalbeds of the Western United States. The methods are multislice long-walling, longwall caving, and high-face longwalling. Foreign practice and possible application in the United States are discussed.

Jan 1, 1979

A study of literature on the epidiorite dykes which transgress the Broken Hill lode and its wall rocks reveals a considerable diversity of thought regarding the time of emplacement of such dykes. In this paper it is deduced that the epidiorite dykes were formed at a late stage and were probably post-ore. Detailed mapping, sampling, and correlation of data from over 100 exposures substantiates this deduction. Physical disruption of the epidiorite dykes is indicated and some interaction of the epidiorite and ore at the time of intrusion is inferred.Further petrological study may confirm this.

Jan 1, 1968

By M. G. Senyur

This study aims at investigating the structural characteristics of backfilling material. In this regard, spatial arrangement of solid particles and associated voids in a unit mass of coal mine refuse as backfilling material were tested. The materials were produced from coal mine refuse of Zonguldak Colliery, Turkey. The experimental procedures were developed to determine their void ratio (or its equivalent porosity), bulk density and the shape properties of constituent particles. The orientation fabric and the co-ordination number were the other two fabric elements determined. The filling materials were sieved and their particle size distributions were found. The results obtained by experiments were related to the particle size distribution parameters, namely, the coefficient of uniformity and the effective size. It was concluded that mean value of void ratio is correlated with coefficient of uniformity. The standard deviation of porosity as an index of fabric heterogeneity is clearly correlated to effective size. By an original experiment, the frequency distribution of coordination number was observed as binomial in uniformly graded materials. Also, the co-ordination numbers of test mixtures were calculated by the Marsal method and results obtained showed a good correlation between the minimum particle size and number of contacts per unit area.

Jan 1, 1998

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1937, was published in Bureau of Mines Information Circular 6942.3/ Information Circular 7007,4/ published as a supplement thereto, listed equipment approved. Burin', the calendar year 1937. The present list includes most of the material liven in these two publications, as well as approvals that have been issued up to January l, 1940. Some equipment formerly listed has been omitted because it has become obsolete or is no longer actively marketed. The list now includes electrically-operated air compressors, coal drills, loading machines and conveyors, mining machine, mine ones, rock-dusting machines, room hoists, storage-battery gathering and haulage locomotives and storage-battery power trucks, mine telephones, junction boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lens, flashlights, methane detectors, and single and multiple-shot blasting units. The appendix at the end of this circular lists trailing, cables that have passed tests prescribed by Schedule 2D. When equipment passes the inspections and tests prescribed by the United Status Department of the interior, Bureau of Mines, in published "schedules" or standards, it is formally approved as "permissible" for use in gassy mines, and the manufacturer is then permitted to mark it with an approval plate that identifies it as having been approved by the Bureau. The inspections and tests are designed to insure that each equipment satisfies the minimum requirements for safety in use. The Bureau's purpose in investigating equipment of this type and listing that

Jan 1, 1940

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970