Search Documents

By Garland Likins

Where soil conditions are favorable, augercast piles have significant economic advantages, but they also have some uncertainty due to the in construction methods. To confirm structural integrity, static testing can be performed on a small sample of piles. Other Non-Destructive Evaluation methods like Pulse Echo are frequently specified for a large percentage of the remaining production piles. However, such NDE methods require testing the pile after the grout/concrete has hardened. If problems are found, then the repair or replacement can be relatively expensive. The confidence in the quality of these piles can be improved by automatically monitoring the grout pumped as a function of depth during the grouting phase of installation. If a low grout volume is detected, the pile can be redrilled and regrouted immediately while the piling rig is still in place and the grout still fluid. This considerably reduces remedial costs. To be effective, such installation monitors must accurately determine both grout volume and depth during installation and be rugged simple to operate. Such an equipment can be of great help to the installation crews. The assurance gained may reduce the need for subsequent NDE tests. The quality of inspection of driven piles depends heavily on the inspection personnel. While inspection is critical in a good installation, it is sometimes assigned a low priority. Inspection personnel in many cases are technicians with little pile experience. They may not understand the project needs or even how the pile driving equipment works. The task is often monotonous and any distraction makes accurate record keeping difficult. In some cases inspection is totally ignored for lack of qualified personnel. Electronic systems can automatically and accurately monitor driven pile installations and include documentation of certain hammer performance parameters. This paper describes equipment available and routinely in use for automated monitoring of both augercast and driven piles and demonstrates applications on typical construction sites. The paper also discusses benefits and limitations of the alternative NDE tests. KEYWORDS: Augercast Piles, Piles, Installation Monitoring, Pulse Echo Method, Integrity Testing

Jan 1, 1999

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

The Ediacara mineral field is classified as a Mississippi Valley type deposit with stratiform mineralization near the base of the Cambrian beds. Mineral deposition was contemporaneous with sedmentation and reerystallization, and mobilization took place after lithification of the sediments. Several mechanisms of deposition were possible.INTRODUCTIONThe Ediacara mineral field is located in the Mt. James Range approximately 300 miles north of Adelaide, about 12 miles west of Beltana railway siding and 10 miles east of Lake Torrens. It is isolated geographically from similar deposits of equivalent age and environment in the Flinders Range Province (Fig. 1). The climate may be described as semi arid with high summer temperatures and frequent dust storms. Occasional thunder storms are the main source of rain in the summer months.The exact date of discovery is unknown, but is believed to be about middle of the last century. Ulrich (1872) was the first geologist to report on the field. At that time only the southern portion of the field had been prospected (and abandoned). Although the prospects did not appear encouraging Ulrich advised prospecting of the shales and testing beneath the limestone.In 1888, Rosewarne, an Inspector of Mines, visited the Southern Workings and queried whether they were connected with some lode at deeper level or were merely bedded deposits. The first geological map with sections was drawn by H.Y.L. Brown (Brown 1892).Brown recognized three principal rock formations as dolomitic sandstone, kaolinised shales and sandstone, and quartzites and sandstone in descending order. These three basic units are still recognized. He recognized also the stratiform nature of the mineralization in the shales as a...

Jan 1, 1963

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By N Currey, G W. Wilson, P Ritchie

Kidston Gold Mine in Queensland, Australia has a 310 ha tailings impoundment that has undergone final closure rehabilitation. Kidston Gold Mine evaluated their closure options for this low acid generating tailings impoundment, and due to a lack of cover soils and the cost of importing material, the mine decided to investigate the possibility of direct vegetation onto the tailings impoundment surface. The mine subsequently embarked upon a well planned and detailed research program to determine the feasibility and sustainability of this closure option. The research program included vegetation trials, toxicology studies for metal uptake by vegetation, as well as a comprehensive closure water balance model for the tailings impoundment complex. This paper describes the results of the long-term closure water balance for the tailings impoundment complex for the pre-closure state of the impoundment, as well as predictions towards the impoundment performance once final rehabilitation of the tailings impoundment complex has been achieved. The water balance presented is unique in that it is founded on unsaturated flow principles and accounts in full the impacts of the surface flux boundary conditions. This novel approach enables the prediction of actual infiltration rates into the tailings impoundment surface, which in turn allows for the calculation of how much seepage will exit from the tailings dam toe drains.

Jan 1, 2003

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Aijuan Zhang, Liang Zhao, Yutao Wang, Yu Bao

In the green backfilling mining of underground coal mines, gangue in a coal seam is used to replace and fill goafs. However, the gas drainage time changes in the amount of gangue output and order in the extraction sequence of stope blocks, thereby changing the production output. A multi-objective integer programming model was proposed to solve this based on an improved non-dominated sorting genetic algorithm. The results show a feasible gangue filling rate can be found and the extraction sequence for a long-term planning time is optimized. It increases the planned annual output by 26% and reduces equipment idle time.

May 23, 2022

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

By Hugo Toledo, Antonio Bravo, Rafael Carpio, Samuel Apolinario

La planta concentradora de compañía minera Antapaccay tiene un circuito de molienda SABC, compuesto de un molino SAG de 40’ x 25’, dos molinos de bolas de 26’ x 40.5’, dos chancadoras de pebbles, un sistema de clasificación con trommel - zaranda en molienda primaria y un sistema de clasificación con hidrociclones en molienda secundaria; este circuito fue diseñado para procesar 70 ktpd de mineral (76 ktpd de mineral efectivo), actualmente la planta concentradora alcanzó una capacidad de 95 ktpd de mineral efectivo, mediante la implementación de iniciativas de excelencia operacional, sin significativos costos de inversión.

Sep 30, 2022

By E. P. Youngman

Zirconium, formerly distinctly a rare element, is rapidly becom- ing of rather extensive commercial importance. Economic features of the zirconium industry, together with general information regarding the metal and its compounds, are discussed in a separate paper, to which this paper is a supplement. In addition to giving a brief discussion of the four or five de- posits that so far have proved to be commercial sources of the element, this circular summarizes available data (including some hitherto unpub lished material from the files of the Bureau of Mines) upon other occur- rences, including many of scientific interest only, of the two commercial. minerals, zircon and baddeleyite, and also data upon some of the minor minerals, such as eudyalite and cyrtolite, which have attracted addition- al interest in recent years because they are frequently richer in hafnium than the more common zirconium minerals.

Jun 1, 1931

By N. B. J. Kieser

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. Platinum-group minerals (PGM) in the enriched zone at Dust Mountain occur in two separate parageneses, the first representing primary magmatic PGM and the second primary magmatic PGM that have been reduced to alloys during serpentinisation. Minerals in the first group were unaffected by hydrothermal alteration on account of their textural setting or stable chemical composition. Despite substantial alteration of the serpentinised assemblage, most evidence points to the dominant role of primary magmatic processes in determining PGM occurrence. Several base metals have nevertheless been introduced hydrothermally. With respect to surficial dispersion the single most important paragenetic factor was the reduction of sulphides to alloys, rendering them more susceptible to mechanical erosion and less so to chemical leaching. The different textural setting of Pd-group and Ir-group phases results in different dispersion characteristics, with major implications for stream sediment sampling

Apr 1, 1994

THE Wonthaggi coal-field lies south easterly from Melbourne at a distance by rail of 86 miles, on the flats of the Powlett River, immediately to the south of the deep-cut valleys and steep intervening ridges in the Jurassic rocks of the Bass Range and itsfoot-hills. The coal-bearing area is covered with a thin layer of late Tertiary and Recent deposits, which serve to mask the true character of the underlying coal-bearing rocks and effectually prevent the appearance of any coal outcrop. Two or three bores sunk prior to 1890 had shown the locality to be really a potential coal-bearing one. Only one additional bore was sunk in the State Coal Mine area until 1908, when energetic boring was resumed, with the result that in November, 1909, when an acute shortage of black coal in Victoria resulted from the prolonged strike on the New South Wales coal-fields, coal-seams had been located at Wonthaggi offering sufficient inducement to start an...

Jan 1, 1918

A large-diameter road tunnel will cross beneath the strait in Istanbul and expand the infrastructure bottleneck between Europe and Asia. The technical planning of the tunneling operations poses complex challenges. Therefore, the construction consortium ordered a specially adapted tunnel boring machine (TBM) from Herrenknecht. The 13.6-m (44.6-ft) machine, a Mixshield, was completed in early July 2013 in Schwanau, Germany. To get from the European to the Asian side of Istanbul, people and goods have to cross the Bosporus Straits. So far, two road bridges as well as ferries provide the only transport link between the two parts of the city and the two continents. The tense traffic situation for the nearly 14 million residents of the city and for international transit traffic should be improved considerably thanks to the construction of a new road tunnel under the Bosporus. ?The project is certainly one of the most challenging tunneling operations currently being addressed in the world,? said Herrenknecht project manager Georg Schleer. The route of the ?Istanbul Strait Road Tube Crossing Project? runs around 100 m (330 ft) below sea level at its deepest point. The interior diameter of the tunnel will be 12 m (40 ft) so that two lanes in each direction can be accommodated. They will extend one above the other on two levels. 3.34 km (2.1 miles) of the tunnel with a total length of 5.4 km (3.3 miles) are being created by a 13.6-m- (44.6-ft-) diameter Herrenknecht TBM that will begin its underground mission from a launch shaft on the Asian side.

Sep 1, 2013