Search Documents

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995

Coal-bearing regions cover about 18,464 square miles or one third of Iowa, primarily in the south-central part of the state. Coal quality ranges from subbituminous to high volatile bituminous. Iowa's coal reserves are estimated to be 2.2 billion tons, less than one-half of one percent of total U.S. reserves. Coal beds are typically thin seams with a maximum thickness of five feet. Coal deposits in Iowa were fist mined in the 1840s for blacksmithing and domestic purposes. Demand for coal increased with the use of coal to fuel steamboats and railroads. Production peaked in 1917, when Iowaproduced9 million tons of coal. Since then, conversion to natural gas and fuel oil has decreased the demand for coal. Today, electrical power generating plants have created a continuing, but declining, demand for Iowa's coal. Coal production in Iowa is by surface mining methods. The Iowa regulatory program was conditionally approved January 21, 1981. Full approval was received March 28,1982, and the Abandoned Mine Land Program was approved March 28, 1983.

Jan 1, 1992

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By J. Hindman, E. Moeller

Vermiculite is currently mined from shallow (less than 25 m or 80 ft) surface deposits throughout the world. The largest producers are Palabora Mining of Phalabowra, South Africa (ore stock is a phlogopitemica), Xinjiang Yuli Xinlong Vermiculite of Korla, China, and W.R. Grace of Enoree, SC (ore stock is a biotite mica). Smaller operations are in Australia, Brazil, Russia and Zimbabwe. They also produce vermiculite on a continuous basis but do not export any significant amounts of product to North America. Intermittent and poorly documented production on a minor scale is reported from Argentina, Egypt, India and Uganda. Worldwide vermiculite production in 2004 increased1.7 percent to 432.8 kt (477,000 st). North American production declined, while African and Chinese production continued to increase.

Jan 1, 2005

By Paloma Lazaro, Moe Momayez

Interactions between human beings and their work environment require the body to regulate its temperature by balancing heat production and loss. Comfortable environmental conditions are crucial for keeping workers safe and healthy and to maintain a suitable level of productivity. However, achieving a proper core body temperature may become challenging under different conditions, especially in high heat-generating workplaces such as hot underground mines. Because hot underground mines have the potential to expose workers to heat stress, compliance with standardized and regulated indices and criteria is distinctly required. The objective of this paper is to provide an overview of the current research on heat stress and strain in hot underground mines, collected from published and specialized literature. General definitions, statistics of heat-related accidents in mining, overview of the indices, standards, and recommendations for heat stress are provided herein.

Oct 6, 2020

By Parker A. J, Ruane M, Wadley L. G B

Copper, sulphur, nickel, cobalt, palladium, silver, and gold can be recovered from the copper sulphide precipitated from the "copper boil" of the Sherritt-Gordon nickel process used at Western Mining Corporation's Kwinana nickel <refinery. The method is based on an oxidative ammonia leach of copper, nickel, and the precious metals at temperatures below 40°C to produce, in part, elemental sulphur, in the residue. This is followed by heating to decompose thiosulphate and remove some ammonia with precipitation of some of the copper, palladium, gold, and silver. Addition of sulphur dioxide to pregnant liquor precipitates copper, as either Chevreul's salt or copper(I) ammonium sulphite, together with the remaining gold and silver. Less than 10 per cent of the dissolved palladium and less than 1 per cent of nickel and cobalt precipitate to this stage.In one option, the Chevreul's salt is dissolved in a solution of copper(II) sulphate, acetonitrile, and water to generate a solution of copper(I) sulphate. Gold and silver do not dissolve. The solution of copper(I) sulphate is thermally disproportionated by distilling acetonitrile to give exceptionally pure copper powder, with desirable characteristics for powder metallUrgy. Nickel, cobalt, and ammonium sulphate are recovered from the motherliquor of the Chevreul's salt precipitation by return to the Sherritt-Gordon process, where recovery procedures already exist. Palladium is recycled for eventual removal as a sulphide with the gold and silver.In the other option, solid copper(I) ammonium-sulphite is <thermally disproportionated in water at 150°C to copper powder.

Jan 1, 1978

A genesis based on new developments in the physical chemistry and flow properties of colloidal substances is proposed for the pipe-like Peko orebody. The rheological behaviour of sediments is governed by the contained colloids. Remobilization of thick pasty sediment during diagenesis is regarded as an essential step in the concentration of metal dispersed in sediments. At a high concentration the sediment pore fluid is a dense gelloid such that van der Waals attractive forces between the colloidal particles exceeds the coulombic repulsion. This permits accretion of the colloids into globular clots and their fracture fragments. These have a uniform size distribution dependent upon the rate of shear, and the sediment lithifies to clotted, porphyry-like, "gritty", dolomitic or igneous-looking intrusions and flows. The physical chemical properties of natural sediment colloids appear adequate to account for ore formation.Adsorption accounts for the dispersion and retention of metal in sediments. Accretion accounts for the segregation of the colloidal materials to give the various types of clotted igneous-looking intrusive source rocks. Syneresis enables the colloids to spontaneously draw together and to dehydrate. Formation of an ordered lattice achieves a lower energy state and desorbs metals and insoluble metal compounds "particle by particle" into the escaping water of hydration and pore water. Peptization enables migration of the metal hydrosols as stable dispersions until they merge for outflow through seepage zones or water extrusion channels. Nucleation and concretion precipitate the metal dispersoids from pore waters seeping through hydrous parts of the source rock, porous beds, faults, and zones of weakness by which the connate waters leave the lithifying sediments. Gelatinous precipitated mineral matter in the ore channels is capable of thixotropic reliquefaction when disturbed by shock or movement. Local reintrusion, flowage, interveinings,brecciation, and intermixing of the materials is the result.The principles of the suggested genesis are applicable to both syngenetic and epigenetic mineral accumulations.

Jan 1, 1966

By Ruxton B. P, Rhodes J. M

Two Rb-Sr ages are discernible in data concerning the leucocratic granite which is the youngest pre-sedimentation phase of the crystalline basement complex at Rum Jungle, Northern Territory, Australia. Whole-rockdata suggest that intrusion of this unit took place at about 2400 my ago, with a probable initial ratio around o·707; whole rock-potassium feldspar tie-lines indicate redistribution of strontium at about 1800 my ago. The former age correlates with other measurements on rocks which form basement to the mantling Pine Creek Geosyncline; the latter correlates also with isotopic evidence for regional metamorphism and emplacement of some younger intrusive granites elsewhere within the geosyncline. A few K-Ar ages, from scattered localities, conform generally with the later event or events which appear to have some connection with the structural deformation clearly observable both in the complex and the surrounding metasediments. It is these younger events which appear to match the residual evidence for the earliest detectable concentration of uranium minerals in the Alligator Rivers district.

Jan 1, 1977

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

Multiple regression analysis was used to predict elemental concentrations of copper and nickel in soils from consideration of the concentration of these elements in vegetation in an ultrabasic complex in New Zealand. Regression equations were computed from sixteen independent variables involving concentrations of ten elements in plant ash, and various physical factors such as slope and altitude of the site, and height of the tree. One elemental and one physical variable were significant for nickel at the 90 per cent level of probability and five elemental and two physical variables were significant for copper at the same level. Use of the regression equations explained 32·5 per cent and 26·5 per cent of the variance in the respective relative accumulations (amount in plant divided by amount in soil) of copper and nickel.Predicted concentrations of copper and nickel in soils agreed more closely with the observed values in the soils than did the levels of these elements in plant ash.Although the results may specifically apply only to the test area, the principles should have universal application.

Jan 1, 1972