Search Documents

By Mark Tsirlin

Kinetics of the initial oxidation stages of diffusive silicide coatings on 8 molybdenum and niobium at 1100 - 1700 and under the pressure of 400 and 1330 Pa has been studied using methods of gravimetry and gas phase analysis of oxygen, as well as by SEK, XRD and EDMA methods. The first oxidation stage described by asymptotic equation in case of NbSi coating changed over to the stage described by parabolic equation. The asymptotic law was shown to depend on non - stationary conditions on the oxide layer boundaries. Interconnection between silicides and quartz structures, on the one hand, and peculiarities of oxidation kinetics, on the other, is [discussed. The possibility of estimation oxygen atom jump frequency in quartz and fractions of oxygen reacting with metal and with silicon proceeding from the analysis of the kinetic data was ascertained. Conditions of oxidation kine- tics transfer from asymptotic (or parabolic) stage to a non - protective "linear" stage, associated with volatile ~roduct formation, are also discussed.

Jan 1, 1995

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

Consumption and intensity of use trends for twelve metals, by industrial end use, were estimated for 1972 through 198Z. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following four of the twelve metal increased from 1972-82 as follows: aluminum, 1.00 percent; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83 percent; titanium, 7.82 percent; and tungsten, 6.09 percent. Consumption. for the remaining eight metals decreased at average annual rates ranging from 0.58 percent (copper) to 5.37 percent (manganese).

Jan 1, 1986

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999