Search Documents

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By A. Kostin

GIS and multivariate geometric distribution have been used to predict the association of high-level intrusives with hydrothermal alteration related to iron oxide Cu-Au (IOCG) mineralizing systems. Several examples in the Russian northeast are presented in this paper. IOCG ore deposits can have enormous geological resources containing significant reserves of base, precious, and strategic metals, and hence are economically attractive targets for mineral exploration. To date, examples of this type of mineralization have not been reported from the northeastern area of Russia. The Tarinskiy ore cluster, located in Eastern Yakutia, shows brecciated altered rocks with sulphide and iron oxide cement, which is typical for IOCG mineralization of the iron oxide Cu-Au±U type. This cluster was formed near surface and is linked with the Rep- Yuruinskiy pluton. It has potential to host new world-class precious metal deposits in northeastern Russia

Jan 1, 2014

By A Kamkar-Rouhani

The paper describes a mineral potential mapping of gold and other base metals in Mahneshan area, Iran, using geographical information system (GIS), in which, the method of weights of evidence is used to combine spatial data obtained from different sources to make prediction for mineral potential. This is a quantitative tool for mineral resource mapping that can be used to delineate and predict favorable areas for further exploration by using the characteristics of known and similar mineral deposits. In accord with the descriptive model for gold and other base metal deposits, the spatial distribution of 20 known mineral occurrences was used. In addition, digital evidential maps were used in this study. The maps include maps of lithological units, faults and first derivative of total aeromagnetic data, remotely-sensing data of alteration and also geochemical evidential maps produced on the basis of the results of chemical analyses of samples taken from the stream sediments in the area, and analysed for Cu, Pb, Zn, Sb, As, Ag, Au, Ba and Hg elements. The binary maps were produced and then combined with the model of weights of evidence using 20 known mineral occurrences to obtain a final map of the favourable areas for further exploration of gold and other base metals in the study area. The final map is a predictive GIS model of the mineral deposits in the area. An interesting matter about the final predictive GIS model is that the faults are mainly located in favorable areas which possesses the most probability of mineralisation. Therefore, the faults in these areas have priority for further exploration of gold and others base metals.

Jan 1, 2005

By Luke Clarkson, David Williams

The intent of this paper is to provide overview context to allow broader understanding of conventional tailings dam failure mechanisms. The research leverages global knowledge, experience, and data collection and interpretation for the safe and controlled management of the geotechnical stability of a tailings storage facility. The motivation for this review is to facilitate transparent access to tailings dam background and understanding. This paper addresses the core understanding of geotechnical failure mechanisms, and how these eventuate to instability and failure of tailings dam structures. This research focuses on foundation failure, internal erosion and piping, overtopping, seepage, seismicity, and slope instability and provides insight into what factors contribute to failure, how failure progresses due to such failure, anticipating and monitoring for the aforementioned failure modes, and designing to mitigate their risk.

Feb 15, 2021

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By E. P. Youngman

The mining law of British North Borneo is entitled " The Mining Ordinance , 1927. 113 The only mining regulation or rule available is " Rules 313 , 114 passed in accordance with article 26 of the ordinance of 1927. Before the passage of this legislation , the country had no specific law governing the granting of mineral rights , although the land law contained provisions relating to mining lands . The land ordinance of 19135 still controls in a few details . All references in this paper , unless otherwise specifically designated , are to the mining ordinance .

Mar 1, 1933

By Branagan D. F

The geology of the area studied is briefly described, together with the prospecting methods used in the search for copper, lead, zinc and uranium ore bodies.Four prospects, Mt. Corella, Yanasinga, Lawlor's and Greenmount, which were diamond-drilled, are described in detail and geochemical results are discussed in relation to the mineralization found. Copper anomalies were found wherever intrusive rocks were mapped, and showed a much closer relation to geology and mineralization than did the predominantly lead and zinc anomalies.Geochemical prospecting aids in the overall mineral search programme because of its speed and economy, as it helps to pinpoint areas worthy of detailed geological examination. Geochemical anomalies are a guide to favourable zones but may not indicate the presence of ore.INTRODUCTIONDuring 1953-55 the National Lead Company of New York carried out a search for minerals in an area south and west of Cloncurry (Fig. 1) in rocks of Precambrian age. After reconnaissance mapping, a number of prospects were chosen for closer examination by detailed geological mapping and geochemical sampling, and from these prospects, five sites were selected for drilling.This paper records the salient features of the exploration programme and discusses the geology and geochemistry of four of the prospects-Mt. Corella, Yanasinga, Lawlor's and Greenmount. Practically all the prospects examined showed high zinc "anomalies" or "dispersion" trains. Greta, Mt. Corella and Lawlor's prospects showed some copper anomalies and, to a lesser extent, lead anomalies. In particular, Greenmount exhibited striking copper anomalies.

Jan 1, 1960

By Ycaro Jorge Maia da Costa

O desenvolvimento de estruturas com dimensionamento confiável requer o monitoramento de seus materiais, entretanto alguns processos de fabricação muitas vezes induzem modificações em seu comportamento mecânico. Isso faz com que as estruturas sejam menos confiáveis podendo causar redução da vida útil. Um dos processos onde isso acontece é a soldagem. Seu aporte térmico, modifica a microestrutura do material de tal forma a gerar três regiões mecanicamente distintas na junta soldada: Metal de Solda (MS), Zona Afetada pelo Calor (ZAC) e Metal de Base (MB), fazendo com que haja concentração de tensão na região afetada. Este trabalho se deteve em analisar o comportamento mecânico de uma junta soldada de aço inoxidável AISI 304 em comparação com o mesmo material não-soldado através da identificação dos gradientes de deformação, utilizando da Correlação Digital de Imagens (CDI) aplicada ao ensaio de tração. Os resultados provaram a capacidade da técnica de CDI em identificar campos de deformação mesmo em materiais anisotrópicos, como uma junta soldada.

Aug 17, 2017

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By V. M. S. R. Murthy, Biswaraj Dash, Somnath Chattopadhyaya

Tunnel boring machine (TBM) has been in focus for the last few decades and is currently the most preferred excavation method for metro, hydro and irrigation tunnels. Tunnelling in hard and abrasive rock conditions, in particular, is adversely affected by a very low advance rate coupled with increased TBM disc cutter failures and cutterhead jamming, seeking an in-depth understanding of the design and operational processes of the boring components of the TBM. The cutterhead and disc cutter are the critical boring components of the machine, influencing the boring process significantly. These components directly interact with the rock and hugely influence the machine’s efficiency. This paper encapsulates a review of prior studies related to disc cutter design and the cutterhead design for hard rock TBM tunnelling. A design methodology for designing and selecting a disc cutter and a cutterhead is suggested. The design methodology has been applied for a hard rock tunnelling case, and suitable design specifications for the boring components were arrived at. The disc cutter and cutterhead specifications designed based on the suggested methodology closely match with that of deployed TBM specifications. It may be observed that except for the case of high-strength and high-abrasive rock (greyish quartzite), for the rest of the rocks, the suggested design can meet the desired advance rates.

Jan 31, 2024

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By Alberto Terrones

En un mundo que cada vez se hace más pequeño, los países latinoamericanos deben buscar una alternativa que oriente su desarrollo y estructure sus economías hacia un mercado común. En ese sentido, es necesario conocer la producción minera y metalúrgica de los distintos países de la América Latina, así como examinar algunos de los proyectos mineros y metalúrgicos que se espera desarrollar a corto plazo con el fin de apreciar o valorar sus posibles repercusiones en las economías nacionales o subregionales. Por ello, el presente texto revisa el panorama actual de la industria minera y metalúrgica de América Latina y plantea mejorar la industria a través de establecer contacto directo con todas las instituciones de técpicos mineros y metalurgistas de los países latinoamericanos para intercambio de publicaciones, la estimulación de la organización de reuniones técnicas regionales y el diálogo de los problemas técnicos y económicos que afecten al desarrollo latinoamericano de la industria minero - metalúrgica.

Jul 1, 1967

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

The author summarizes and extends the relevant results of papers previously published by various authors and presents these results in chart form. The charts are used to demonstrate the theory on a hypothetical mine.INTRODUCTIONRecently a series of articles have dealt with leakage in a mine ventilation system and the problem of its reduction.Theories were developed by Peascod and Keane (1955) for the combined effect of flow in the airways and leakage through the porous barrier between the intake and return of an ideal mine. Later Keane and Peascoa. (1956) extended these ideas to the use of an underground booster fan in increasing the face ventilation and showed how to determine the water gauge and location of the most efficient underground fan.These articles were based on the assumption that Atkin:son's formula:P = R Q2 (1)gave the relation between the pressure drop P lb'/sq. ft., the quantity, Q kilocusecs, flowing in the mine airways and the total resistance, R Atkinsons, to air flow offered by the mine roadway. An Atkinson is defined as a resistance such that 1 kilocusec of air flows due to a pressure drop of 1Ib.jsq. ft. However for conditions prevailing in most mines a more :appropriate relation is that postulated by Reynolds and others (Lamb, 1953) :P=R Qn (2)where n has some value slightly less than 2. It should be noted that Atkinsons may not be used as units when n is not equal to 2.

Jan 1, 1958