Search Documents

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By W. D. Sinclair

"Between 1934 and 1956, nearly 31 million grams of gold were produced in the Matachewan area from deposits on properties belonging to Young-Davidson Mines Limited and Matachewan Consolidated Mines Limited. In 1979, production from these properties was renewed by Pamour Porcupine Mines Limited.Most of the gold produced has come from relatively lowgrade deposits (3.4 gl t or less) that occur in an east-trending belt of dykes and irregular bodies of trachytic syenite. Although small by comparison, these deposits have some of the characteristics of porphyry copper-molybdenum deposits. The mineralized syenite contains up to 5 per cent disseminated pyrite and is highly fractured and cut by quartz and quartzcarbonate veinlets. Gold occurs as native gold along fractures, in quartz veinlets and as minute inclusions in pyrite. Minor chalcopyrite and trace amounts of scheelite, molybdenite and galena are also present. Mineralization was accompanied by potassic alteration, consisting mainly of potassium feldspar.Some gold was also produced from small, but higher-grade, deposits in volcanic rocks. These deposits occur near the syenite-hosted deposits and consist of quartz veins and stringers mineralized .with pyrite and gold. Minor gold is present in some low-grade, porphyry-type copper-molybdenum occurrences and, locally, in large, isolated quartz veins.Lead isotope analyses suggest that the gold deposits were formed at about 2700 Ma and were locally remobilized at approximately 2400 Ma, following the Kenoran orogeny. The deposits appear to be genetically related to felsic magmas emplaced in an epizonal environment and deposited from hydrothermal solutions relatively concentrated in S and K20."

Jan 1, 1982

The U.S. economy showed further strength during the third quarter of 1983, continuing the upward trend discussed in the last two issues of Minerals and Materials. The National Association of Purchasing Management composite index increased to a 10-year high of 67. 1 in July. (A value of 50 or greater indicates expanding industrial activity.) The index, a weighted composite of new orders, production, employment, vendor performance, and inventories, is derived from a survey of purchasing agents for about 250 industrial firms. Investment and Other National Economic Indicators The strong consumer surge of second quarter 1983 was reinforced during the third quarter by the performance of private investment. Because of this, many analysts became more optimistic about the strength of the recovery and its potential for being sustained. Capital investment growth, negative since 1980, was positive for every investment component in the third quarter of 1983. Preliminary estimates indicate a real increase of $1.4 billion (at an annual rate) in private investment expenditures on nonresidential structures, an increase of $4.3 billion (at an annual rate) for producers' durable equipment, and an increase of $4.8 billion (at an annual rate) in real inventory levels. The second quarter 1983 increase in expenditures on producers' durable equipment was the first indicator that investment recovery would occur during the rest of the year (table 1). Corporate profits in total manufacturing increased $6.5 billion from first quarter to second quarter 1983 (table 2).

Jan 1, 1983

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By Hal J. Kelly

A number of problems that developed in processing the halloysitic clays of eastern Washington and northern Idaho were investigated by the Bureau of Mines. The deflocculating effect of tetra sodium pyrophosphate is compared with several other compounds, and on the basis of current theory, the advantage of sodium pyrophosphate as a deflocculating agent is explained. The adsorption of the sodium ion by clay in a clay"-water system was established by a radioactive tracer technique, and the deflocculating action of sodium pyro- phosphate was postulated. The effective dispersion of the halloysitic clays was limited by the occurrence of tightly bound aggregates of small, individual crystals. Disaggregation of the agglomerates was investigated by liquid extrusion and ball milling of dilute slurries and by extrusion of the clay in a plastic state. The greatest increase in the production of small particles was by high? pressure liquid extrusion.

Jan 1, 1963

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By AIME AIME

WTHIN the next month all members of the Institute will be given an opportunity to vote for a new President, two Vice-Presidents, and five Directors. All of the candidates nominated by the official committee are well known to certain groups of the Institute membership but a brief record of their professional lives will be given here for the information of those that will vote. Not since 1927, when Everette DeGolyer guided the destinies of the Institute, has a member of the Petroleum Division been a candidate for President. John Meston Lovejoy has been a Director since 1930, and a Vice-President as well for the last year: In the three years 1932-4 lie was also chairman of the Admissions Committee. Dir. Lovejoy graduated from the Columbia School of Mines in 1911, just before lie was 22 years old, and began his professional career as a copper miner at Chuquicamata. Chile. Silver and gold mining later claimed his % attention, and it was not until 1914 that lie gut into the oil business, as geologist for the Standard Oil Co. of N. Y. This took hint to China and he later worked for the company in Wyoming. In 1917 lie joined the Army where lie rose to be captain of Field Artillery. Upon his return to the United States he went to work for the Amerada Petroleum Co., of which he later became vice-president and general manager, with headquarters in Tulsa. Since coining to New York he has been president of the Petroleum Bond & Share Cu.. and is currently president of the Seaboard Oil Co.

Jan 1, 1935

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

When I was first asked to give a paper on work-life balance in the mining industry I was both excited and aware of the incongruity of my position. I have never worked in mining operations nor have I had any experience that approximates the on-site lifestyle. IÆm not really an adventurer or a traveller, I prefer writing and research to hands-on activities and IÆve never worked further than twenty minutes away from home. The perspective I offer is thus largely an objective one. I say largely since I grew up in a family where my parents work arrangements involved long-distance commuting; my dad continues to work FIFO at a coalmine in Blackwater until this day. Perhaps my tortoise-like existence is a rebellion against his flighty movements. The analysis I will be presenting today draws together a variety of sources, from member anecdotes and research on FIFO and work-life balance to the popular philosophy writings of a bald Englishman with a French name. I am speaking of the famous writer, Alain de Botton, whose television show æThe Consolations of PhilosophyÆ you may have seen on the ABC. Work-life balance is a term that gets a lot of mileage in corporate brochures and at breakfast seminars. But like many terms that get bandied around in the human resources circuit, from æteam synergyÆ to æperformance optimisationÆ, I am frequently perplexed as to what it actually means. Corporate websites are at pains to emphasise the high priority that they place on the needs of the whole person. Yet in terms of substantive content, a commitment to work-life balance often seems to translate into little more than the option to take a few morning yoga classes in exchange for working a seventy-hour week. As extended work hours have taken their toll, leading to high attrition of professionals across all industries, employers are increasingly expending resources to discover just what lies behind this buzz word. The challenge for companies is to find meaningful strategies to help employees better integrate different aspects of their lives in a new era of work, as employees are sending the message that they are not willing to play work, social life and leisure off against each other in a zero sum game.

Jan 1, 2005

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By H. Z. Kuyumcu

Associated with the development of a novel microbiological oxidation process for the conditioning of iron hydroxide slurries from ferrous mine waters, there is a realistic chance to make the contained iron available for a material utilization. The transformation of ferrous into ferric compounds is coupled with the precipitation of iron hydroxisulphate mostly in terms of the mineral Schwert-mannite. The further treatment of the iron hydroxisulphate has to be aimed on the processing for product recovery and product refinement. For many potential applications, e.g. in the ceramic industry, the pigment industry or for metallurgical applications, the removal of sulphate is essential. For the dehydration of the iron hydroxisulphate and the sulphate removal, microwave heating technology is a beneficial method. In contrast to conventional thermal heating processes the supply of energy in microwave application takes place directly within the material through the dissipation of electromagnetic energy, i.e. no heating medium is needed. It is a volumetric heating process regardless of the surface of the material. The rapid and targeted energy supply and the good controllability of microwave heating systems are advantages which have led to a wide variety of applications in industrial processes. Among the diverse use for heating of temperature-sensitive, chemical and pharmaceutical products as well as foodstuffs the number of applications also in mineral and solid processing increases. At the Department for Mechanical Process Engineering and Solids Processing of the Technical University Berlin the use of microwave technology for the treatment of iron hydroxisulphates has been investigated systematically within the framework of a cooperative research project. The paper at hand shows results from material conversion tests subject to a variation of the relevant process parameters. The reaction products are characterized and the process is compared with the conventional heating in a rotary kiln.

Jan 1, 2014

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By Malcolm D. Flavel

Much has been said and written about the world's, and particularly the united states of America's, energy crisis. The relative changes between cost components of production have altered because the days of cheap energy have now gone. Decisions that made capital investment reduction attractive to treat large tonnage lower grade ore bodies appear to be no longer valid because average energy costs for comminution that were less than 1 cent per kilowatt hour in 1972, are now more than 3 cents and will shortly become 6 cents according to some projections. Increased capital investment to improve processing energy efficiencies are certainly going to be pursued. Energy today is the largest cost component in the average mineral production facility. It takes more than 12000 kilowatt hours to produce one ton of finished steel and more than 60000 kilowatt hours for each ton of copper and aluminum.

Jan 1, 1980

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997