Search Documents

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By M. L. Jeremic

The design of the long-hole sublevel mining method was originally based on the traditional assumption that the principal load was due to the weight of the overlying rock, and that the horizontal stresses are equal to one-third of the vertical stress. However, as mining progressed, the virgin lateral stress was found to be equal to or greater than the vertical stress. The virgin stress in the rock mass is not uniform throughout the folded orebody and adjacent strata. From detailed investigations, three basic patterns of virgin stress in ore panels have been inferred: uniform, bent and twisted. Stresses induced by stoping are up to three times greater than original stresses in the rock mass; they cause heavy ground conditions and make extraction of ore difficult. In the last ten years, the original mining system has been modified several times in order to destress the ground and improve the extraction of ore.

Jan 1, 1978

By D. E. Van Dillen

Three-dimensional structural analyses of three instrumented areas of a deep, longwall coal mine have been performed using the finite element code BMINES. The three Instrumented areas include two single-entry portions and one double-entry portion of the Sunnyside No. 1 Mine, Sunnyside, Utah. The finite element models simulated the sequence of excavation in each test area: the advance of the entry, installation of structural supports, retreat of the longwall, caving behind the longwall, and accumulation and loading of the gob. The structural supports considered in these finite element models include rock bolts, wood cribs, concrete cribs, steel arch sets, and chocks. Mechanical simulation of the geologic environment is achieved through elastic/ perfectly plastic material models employing anisotropy to represent finely layered regions of the medium. The results of these calculations are com-pared with the instrumentation readings from the mine. These measurements include closures, crib loads, rock-bolt forces, and stress growth.

Jan 1, 1978

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Dave Otto, Ron Elliot, Ed Hatch

This paper is a summary of the work carried out by an international team of specialists in the successful explosive compaction of the sand fill core of the Molikpaq offshore oil production structure. The sand fill core is an essential element for the stability of the structure. The sand core must resist liquefaction forces caused by heavy wave action, ice loading, and earthquakes. Explosive compaction methods were used to improve the stability of 220,000 cubic meters of coarse dredged sand placed in the core area. This project was challenging for a number of reasons. It was performed offshore in Russia, seven kilometers off the East Coast of Sakhalin Island. Logistics were a challenge, not just in getting the men and materials to the site, but also working with restricted headroom inside an operating oil drilling platform. This project called for the use of specialty explosives, strict blast vibration controls requiring a complex sequential blast design, and use of custom designed drill rigs. As Russian equivalent explosives were not available, the project involved getting approval for use of North American explosives in Russia, and use of a combined Russian - Canadian blasting crew. The blasting program was carried out successfully, meeting the required densification target _in a safe, effective manner, with no damage to the structure.

Jan 1, 2000

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

By M. B. Shongwe

Pt-based alloys are being developed for high-temperature applications with the aim of replacing some of the currently used Ni-based superalloys (NBSAs) in the highest temperature applications. The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert than nickel and has a higher melting point, they can potentially be used at higher temperatures, up to 1300°C, and in more aggressive environments. Several experimental Pt-based alloys were studied at Mintek, and an optimum composition was found to be Pt84:Ahi:Ru2:Cr3 (at.%). On the basis of hardness and microstructure, a later study identified a new optimum: Ptr8:A111:Ru5:Cr6 (at.%). There are at least two Pt3A1 allotropes, and the high-temperature cubic structure has better properties than the lower temperature tetragonal form, and so needs to be stabilized. This work describes the latest results obtained in transmission electron microscopy (TEM) studies of the quaternary Pt-based superalloys. These results are both interesting and important, because the samples have a higher precipitate density compared to those from earlier work. The precipitate morphology is mainly cubic, with minor areas having irregular-shaped precipitates. The high volume fraction of the precipitates is a major breakthrough, since the objective of this work is to improve the alloys. A prior disadvantage was that the proportion of the precipitates was too low in samples before this work, especially compared with the work from Germany on Pt-Al-Cr-Ni¬-based alloys as well as the NBSAs. TEM -Pt3A1 diffraction patterns were studied, and for each diffraction pattern, many possible lattice point combinations were tried, with the angle between the lattice spots as well as interplanar spacings being calculated for each phase (cubic or tetragonal) to match the measured results. An overall analysis of the diffraction results indicates that the cubic phase fitted the experimental lattice points with much lower errors compared to the tetragonal phase. Thus, with the close match achieved with the cubic structure, the structure of -Pt3A1 precipitates is likely to be cubic. X-ray diffraction has been carried out on selected samples, and the results confirmed the presence of cubic -Pt3A1 and (Pt). Different X¬ray diffractometers were used to further verify the results, and the results were also compared with those from TEM.

Jan 1, 2012

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

The Institute has prepared a list of Societies' publications, magazines, . etc., which were duplicates and were discarded at the time of the consolidation of the libraries of the three Founder Societies. These books will be disposed of about March 1, 1916 by the Board of Directors of the Institute through the Library Committee. If, meanwhile, members who have incomplete sets of these books, or for any other reason desire to secure some of them, they are asked to communicate immediately with the Secretary, as this is in unusual opportunity to secure books at a very low price. American Gas Light Journal, viols. 31 to 39. American Institute of Electrical Engineers, Transactions, vols. 5 to 26. American Machinist, vols. 3 to 20, 22 to 29. American Society of Civil Engineers, Transactions, vols. 2 to 10, 21 to 24, 26 to 33, 39 to 49, 52, 55, 58, 74. Index, viols. 1 to 21. American Society of Mechanical Engineers, Transactions, vols. 1 to 28. Index, vols. 1 to 20, vols. 1 to 25.

Jan 1, 1916

By Robert S. Nichols

Fording Coal Limited's mine in the Rocky Mountains near Elkford, B.C. has produced 21.8 million clean tonnes of metallurgical coal from 1971 to 1980, inclusive. This production has come from several pit areas and required the removal of 149.1 million bank cubic meters of waste rock and overburden by truck-shovel and dragline operations. Waste dumps from 30m to 200m in height have been successfully constructed on natural slopes, generally between 10° and 26°. Design considerations for the dumps include foundation and soil conditions, natural slope angles and containment of weak overburden or rehandle materials. Dump control is maintained by monitoring the crest and the face of an active dump area. Crest movement is measured by extensometers locally termed "Spoil Monitors". When crest movement rates progressively increase above normal, dumping operations are temporarily relocated. Some unstable conditions and mass failures have occurred as the result of natural foundation slopes being in excess of 26°, failure of weak water saturated foundation soils or weak material being placed on the dump.

Jan 1, 1983

The Illawarra District, from 50 to 100 miles south of Sydney, is one of the State's important coalfields. It extends from Clifton on the north, to the Shoalhaven river on the south, and from the coast westward beyond the coastal scarp.For descriptive purposes, this area falls naturally into two zones:(a) the coastal belt backed-by the eastern edge of the plateau;(b) the plateau, westerly from the coastal scarp.(a) The Coastal Belt.A triangular shaped area extending from Clifton to the Shoalhaven river, composed for the most part of soft coal measures strata of Permian age, which, on weathering, undermines the massive overlying Mesozoic sandstones and causes the gradual recession of thecliffs.South of Wollongong, upper marine sediments and contemporaneous igneous rocks make their appearance beneath the coal measure beds and occupy the greater portion of the coastal belt.(b) Plateau Area.Extending westerly from the coastal escarpment is a plateau known as the Robertson Tableland, composed of Triassic sandstone and shales dipping gently in a northerly direction, and capped in places by Wianamatta. shales and r.rertiary basalts. This tableland is approximately 2400 feet above sea level in the vicinity of Robertson, and gradually falls to about 750 feet at Waterfall.The plateau area for the most part is highly dissected, rough, steep gorges alternate with sharp ridges.A large part of the northern watershed of the Robertson tableland is a reserve for Sydney water supply, and large dams have been constructed at Cataract, Avon, Burke, and Cordeaux.

Jan 1, 1938

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By J. A. Taylor, R. J. Fowell

Abstract: The amount of published literature pertaining to the field of rock mechanics has increased markedly in recent years. Whilst computer applications aid our understanding of the mechanisms of pillar instability, the applications do not take into account the effect of time; thus the determined pillar factor of safety has limited meaning. A more realistic approach would be to consider pillar stability in terms of time to failure. However such an approach would require a reasonable estimate of the in-situ pillar mass strength and a validated methodology linking the time to failure with in-situ pillar mass strength and the geometric layout of the working. Résumé: Le volume de bibliographie au sujet de la mécanique des roches a augmenté considérablement ces derniêres années. Alors que des modeles informatiques aident a la compréhension des mécanismes d'instabilité de pilliers, ces modèles ne prennent pas en compte les effets du temps; ainsi, la determination du coefficient de surete du pillier a un sens limité. Une approche plus réaliste devrait considérer la stabilité du pillier en fonction du temps de défaillance. Cependant une telle approche exigerait une estimation raisonnable de la resistance du massif rocheux du pillier ainsi qu'une méthodologie qui lie le temps de défaillance avec la résistance in-situ du massif rocheux du pillier et la géometrie de l'excavation souterraine. Zusammenfassung: Die Anzahl der Veröffentlichungen auf dem Gebiet der Felsmechanik ist in jüngster Zeit sehr gestiegen. Computerprogramme sind wertvoll um den Mechanismus der Pfeilerunbeständigkeit zu verstehen, aber sie vernachlässigen den Zeiteffekt. Daher haben die errechneten Sicherheitsfaktoren der Pfeiler nur begrenzte Bedeutung. Eine realistischere Bewertung wäre, die Stabilität der Pfeiler auf Grund der Zeit bis zum Verfall zu beurteilen. So ein Verfahren würde eine Schätzung der in-situ Gebirgsfestigkeit und eine validierte Methologie, die die Zeit zum Verfall in Abhängigkeit der in-situ Pfeilerfestigkeit und der geometrischen Auslage der Grube zusammenbringt, brauchen.

Jan 1, 2003

By Giuseppe Pintaude, Carlos Mauricio Lepienski

The evaluation of the tribological behavior of thermochemically treated surfaces, such as carburising and nitriding, is of uppermost importance for the productive chain of tools, molds and matrices. However, the use of tribological tests for these surfaces should be well selected to avoid erroneous evaluations, in particular considering the effect of the substrate at different levels. In this context, the linear scratch test may be well suited to distinguish the roles of the surface and the substrate. For that purpose, this paper presents a review on the use of this type of test for tribological evaluation in terms of the performance of thermochemically treated surfaces. The approach used is multiscale, considering what types of results are obtained from each load range used and the applications for each one of them.

Nov 22, 2018

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By William M. Gleason

When SME’s 2006 Arizona Conference convened in December at the Hilton El Conquistador Resort in Tucson, AZ, there was considerable excitement among the 387 attendees. There was a noticeable buzz surrounding the progress of Phelps Dodge’s Safford copper mine in southern Arizona, one of the first new major copper mines to be permitted in more than 30 years in the United States. There were also plenty of good feelings about the mining industry in general. Commodity prices remained high and with no signs of a slowdown in the immediate future. Things were good in Arizona. But there were also cautionary tones at the conference and the Mining Foundation of the Southwest banquet that preceded it.

Jan 1, 2007

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

That electricity is an important and valuable agent, the limit of whose capacity for utilisation is as yet unknown, is a truism; although enormous advances have been made, the possible developments are yet greater. Mining, along with other industries, shares already to a large extent in the practical utilisation of this agent. Electrical engineers have been employed for several years past in developing and applying electricity to all classes of machinery, and for every purpose where power is required and in no instance, that the writer is aware of, has its use been curtailed in favour of any other agency now known, while extensions are continually made. The first modern electric motor was shown at the Vienna Exhibition of 1873, and it was used to work a pump through a mile length of cable but it was not before 1878, that an electric motor was put into daily commercial use by Messrs. Chretian and Felix to work a beet sugar hoist. This early plant effected a saving of 40 % as compared with hand work.In 1879, the first Electric Railway was constructed for the Berlin Exhibition, and in the same year, Mr. T. A. Edison was running an experimental line at Menlo Park. The first electric line opened for the public, was constructed by Siemens and Halske, in 1881, at Lichtenfelde, and was 11 miles in length.

By J. P. Harrison, J. A. Hudson

ABSTRACT: Given the current widespread use of numerical models for rock mechanics and rock engineering, and the ‘Technology Road Map’ theme of the Congress, it is timely to consider the key issues in matching numerical models to rock engineering problems. The three main aspects are: a) identifying the mechanisms, variables and parameters that are relevant to a particular rock engineering project; b) establishing the content and mode of operation of a particular code; and c) deciding whether a particular code provides an adequate model for a particular project. We summarise the key issues, highlighting the concept of rock mass domains, validation and the ability to present the results of a modelling exercise. We include three compact numerical modelling case examples to illustrate the points. Finally, we also present a ‘roadmap’ to assist in the process of matching a numerical model to the rock reality. RESUME: Considérant l’utilisation généralisée des modèles numériques en mécanique des roches et en ingénierie au rocher ainsi que le thème du congrès ‘technology road map’, il est opportun d’aborder les problèmes essentiels liés au choix des modèles numériques dans les problèmes ingénierie au rocher. Les trois aspects principaux sont : a) l’identification des mécanismes, variables et paramètres appropriés au projet considéré, b) la définition du contenu et du mode de fonctionnement d’un code numérique donné, et c) la possibilité de décider si un code donné fourni un modèle approprié au projet considéré. Les points clés sont résumés en mettant en évidence les notions de “massif rocheux”, de validation et de capacité à présenter les résultats d’une approche numérique. Nous présentons trois brèves études de cas qui illustrent ces points. Enfin, nous proposons aussi un logigramme pour aider au choix d’un modèle numérique approprié pour représenter la réalité d’un problème au rocher. ZUSAMMENFASSUNG: Im Licht der augenblicklich weitverbreiteten Nutzung von numerischen Modellen in der Felsmechanik and im Felsingenieurbau und unter Beruecksichtigung der Themenstellung des Congresses “Technology Road Map”, erscheint es an der Zeit die Kernprobleme, die sich mit Fragen der Abstimmung der numerischen Modele mit Hinblick auf ihre Anwendbarkeit im Felsingenieurbau beschaeftigen, naeher zu befassen. Die drei wesentlichen Aspekte sind: a) Identifizierung der Mechanismen, Variablen und Parameter, die fuer ein bestimmtes Projekt im Felsingenieurbau von Bedeutung sind; b) die Festlegung des Inhalts und des Modus Operandi eines bestimmten Codes, und c) die Entscheidung darueber ob ein bestimmter Code ein hinreichendes Model fuer ein bestimmtes Projekt ergibt. Wir fassen die wichtigsten Punkte zusammen, heben dabei das Concept der Gesteinsmassen Domaenen (Rock mass domains) hervor, und erarbeiten ihre Beurteilung und die Moeglichkeit diese zu praesentieren in den Ergebnissen einer Model Uebung. Wir schliessen drei Beispiele von numerischen Modellen ein in denen diese Punkte erlauetert werden. Zuletzt schlagen wir eine “Roadmap” vor, um dem Prozess der Abstimmung des numerischen Modells mit der “Felsmechanischen Wirklichkeit” zu unterstuetzen.

Jan 1, 2003

By R. L. Merek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalities coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance.

Jan 1, 1930